Acuity Brands Lighting HYDREL Installation guide

Brand: Acuity Brands Lighting

Model: HYDREL

Type: Installation guide

7/29/14

INS-RHYTHM

9144 Deering Avenue | Chatsworth, CA 91311 | www.hydrel.com

Phone: 866.533.9901 | Fax: 866.533.5291

Installation should be performed by a qualiﬁed

electrician in accordance with the National Electrical Code

and relevant local codes.

iNSTALLATiON iNSTRUCTiONS

RHYTHM SERiES

1) Attach Mounting Plate Assemblies (A) to mounting surface using qty two (2) each ¼-20x1” socket head cap screw

fasteners (B) provided and appropriate surface anchors (not provided).

a. Mounting Plate Assemblies (A) should be spaced no further apart than 4” less than the ﬁxture overall length.

b. Two (2) Mounting Plate Assemblies (A) are required for RHY2, RHY3, & RHY4

c. All customer supplied mounting anchors must be suitable for use in the mounting surface material, capable of

supporting ﬁxture weight and meet all applicable building code requirements.

2) Loosen ﬁxture Track Screws (D) located on Fixture Assembly (C) ¼ - ½ turn so that Fixture Mount Slide (E) moves

freely along Fixture track.

3) Slide Fixture Mount Slide (E) along ﬁxture length until openings align with Mounting Plate Assembly rods.

4) Attach Fixture Mount Slide (E) to Mounting Plate Assembly rod and tighten qty two (2) each 10-32 set screws (F)

on each Mounting Plate Assembly (A).

5) Re-tighten Track Screws (D).

6) Rotate ﬁxture to aim as required and tighten qty. two (2) each ¼-20 Slide Screws (G) on each Fixture Mount Slide (E).

MOUNTiNG ARMS

Mount Plate Assembly

¼-20x1” socket head cap fastener

Fixture

Track Screws

Fixture Mount Slide

10-32 Set Screws

¼-20 Slide Screws

WARNiNG: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, INJURY OR SIGNIFICANT PROPERTY DAMAGE

For your protection, read and follow these warnings and instructions carefully before installing this ﬁxture. These instructions do not attempt to cover all installation

situations. If you do not understand these instructions or additional information is required, contact Hydrel Lighting or your local Hydrel Lighting distributor.

DISCONTINUED

7/29/14

INS-RHYTHM

9144 Deering Avenue | Chatsworth, CA 91311 | www.hydrel.com

Phone: 866.533.9901 | Fax: 866.533.5291

Installation should be performed by a qualiﬁed

electrician in accordance with the National Electrical Code

and relevant local codes.

iNSTALLATiON iNSTRUCTiONS

RHYTHM SERiES

1) Attach Mounting Plate Assemblies (A) to mounting surface using qty two (2) each ¼-20x1” socket head cap screw

fasteners (B) provided and appropriate surface anchors (not provided).

a. Mounting Plate Assemblies (A) should be spaced no further apart than 4” less than the ﬁxture overall length.

b. Two (2) Mounting Plate Assemblies (A) are required for RHY2, RHY3, & RHY4

c. All customer supplied mounting anchors must be suitable for use in the mounting surface material, capable of

supporting ﬁxture weight and meet all applicable building code requirements.

2) Loosen ﬁxture Track Screws (D) located on Fixture Assembly (C) ¼ - ½ turn so that Fixture Mount Slide (E) moves

freely along Fixture track.

3) Slide Fixture Mount Slide (E) along ﬁxture length until openings align with Mounting Plate Assembly rods.

4) Attach Fixture Mount Slide (E) to Mounting Plate Assembly rod and tighten qty two (2) each 10-32 set screws (F)

on each Mounting Plate Assembly (A).

5) Re-tighten Track Screws (D).

6) Rotate ﬁxture to aim as required and tighten qty. two (2) each ¼-20 Slide Screws (G) on each Fixture Mount Slide (E).

EXTENDED ARMS & STRUTS

WARNiNG: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, INJURY OR SIGNIFICANT PROPERTY DAMAGE

For your protection, read and follow these warnings and instructions carefully before installing this ﬁxture. These instructions do not attempt to cover all installation

situations. If you do not understand these instructions or additional information is required, contact Hydrel Lighting or your local Hydrel Lighting distributor.

Mount Plate Assembly

¼-20x1” socket head cap fastener

Fixture

Track Screws

Fixture Mount Slide

10-32 Set Screws

¼-20 Slide Screws

DISCONTINUED

Installation should be performed by a qualiﬁed

electrician in accordance with the National Electrical Code

and relevant local codes.

iNSTALLATiON iNSTRUCTiONS

RHYTHM SERiES

7/29/14

INS-RHYTHM

9144 Deering Avenue | Chatsworth, CA 91311 | www.hydrel.com

Phone: 866.533.9901 | Fax: 866.533.5291

Fixture to SSBR Surface Box Connection

1) Route ﬁxture cord along ﬁxture and Mounting Plate Rod (H) and secure with provided Wire Keepers (I) (J).

2) Trim excess cord at SSBR, strip back jacket approximately 4”, and slide through ½” Cord Seal (K) provided.

a. Note: ½” Cord Seal (K) may be utilized on either side of SSBR as required by installation.

3) Make electrical load connections as indicated on the labeled conductors and per all NEC and local code

requirements.

SSBR

Mounting Plate Rod

Wire Keepers

Cord Seal

WARNiNG: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, INJURY OR SIGNIFICANT PROPERTY DAMAGE

For your protection, read and follow these warnings and instructions carefully before installing this ﬁxture. These instructions do not attempt to cover all installation

situations. If you do not understand these instructions or additional information is required, contact Hydrel Lighting or your local Hydrel Lighting distributor.

DISCONTINUED

Installation should be performed by a qualiﬁed

electrician in accordance with the National Electrical Code

and relevant local codes.

iNSTALLATiON iNSTRUCTiONS

RHYTHM SERiES

7/29/14

INS-RHYTHM

9144 Deering Avenue | Chatsworth, CA 91311 | www.hydrel.com

Phone: 866.533.9901 | Fax: 866.533.5291

6“ Min

Above Grade

6“ Min

Concrete Pedestal

(2 Places - RHY 2, 3, 4)

Location M

Fixture to BPCA/BPCB Polymeric Ground Box Connection

1) Route ﬁxture cord along ﬁxture and secure with provided Wire Keepers (I).

2) Trim excess cord at BPCA/BPCB, strip back jacket approximately 4”, and slide through ½” Cord Seal (K) provided.

a. Note: BPCA/BPCB must be ordered with ½” NPT at location “M” for use with Rhythm Fixtures.

3) Make electrical load connections as indicated on the labeled conductors and per all NEC and local code

requirements.

BPCA/BPCB

Wire Keepers

Cord Seal

WARNiNG: FAILURE TO FOLLOW THESE INSTRUCTIONS AND WARNINGS MAY RESULT IN DEATH, INJURY OR SIGNIFICANT PROPERTY DAMAGE

For your protection, read and follow these warnings and instructions carefully before installing this ﬁxture. These instructions do not attempt to cover all installation

situations. If you do not understand these instructions or additional information is required, contact Hydrel Lighting or your local Hydrel Lighting distributor.

DISCONTINUED