Agri-Fab 45-03882 User manual

Category
Spreader
Type
User manual

This manual is also suitable for

3
MAINTENANCE
1. Oil the free spinning wheel once a year or more often
as needed.
2. Oil the nylon bushings in the frame tube and the
cross brace once a year or more often as needed.
3. Apply a light coating of grease to the gears as
needed.
4. Before each use make a thorough visual check of
the spreader for any bolts and nuts which may have
loosened. Retighten any loose bolts and nuts.
5. Make sure the tires are adequately inated. Do not
inate beyond the maximum pressure printed on the
tire.
ENGLISH
SAFETY INFORMATION
1. Read the information on the chemical package for
instructions and cautions on handling and applying.
2. Wear eye and hand protection when handling and
when applying lawn or garden chemicals.
3. Never allow children to operate the vehicle or
spreader.
OPERATION
Do not use powdered lawn chemicals. They do not give a
satisfactory or consistent broadcast pattern.
1. Estimate the size of the area to be covered and
calculate the amount of material required.
2. Set the adjustable stop according to the ow setting
recommended in the application chart on this page.
Also refer to the instructions on the packaging for the
material to be spread.
3. Make sure the control lever is in the "OFF" position.
4. Fill the hopper, breaking up any lumpy fertilizer.
5. Start the spreader in motion and then pull the control
lever forward against the adjustable stop to the "ON"
position.
6. Always move the control lever to the "OFF" position
before turning or stopping.
7. To ensure uniform coverage, make each pass so that
the broadcast pattern slightly overlaps the pattern
from the previous pass. The approximate broadcast
widths for different materials are shown in the
application chart on this page.
8. For rectangular areas, make two passes across
the short ends to create turning areas. For non-
rectangular areas, make two passes around the
entire border.
9. When broadcasting weed control fertilizers, make
sure the broadcast pattern does not hit evergreen
trees, owers or shrubs.
STORING
1. Empty the spreader after each use, storing left over
material in its original bag.
2. Rinse the inside of the hopper and the exterior of the
spreader and dry off before storing.
3. Store in a clean, dry area.
TYPE MATERIAL FLOW SETTING SPREAD
WIDTH
FERTILIZER
Granular 3 - 5 2,4 m - 3 m
Pelleted 3 - 5 3 m - 3,6 m
GRASS SEED
Fine 3 - 4 1,8 m - 2,1 m
Coarse 4 - 5 2,4 m - 2,7 m
ICE MELTER 6 - 8 3 m - 3,6 m
APPLICATION CHART
IMPORTANT: Minor setting adjustments may be necessary to
compensate for humidity and moisture content of the material.
ADJUSTABLE STOP
CONTROL LEVER
WING NUT
TYPE MATERIAL FLOW SETTING SPREAD
WIDTH
FERTILIZER
Granular 3 - 5 8' - 10'
Pelleted 3 - 5 10' - 12'
GRASS SEED
Fine 3 - 4 6' - 7'
Coarse 4 - 5 8' - 9'
ICE MELTER 6 - 8 10' - 12'
21
45-03882-KD
the fastest way to purchase parts
www.speedepart.com
1
2
3
4
5
6
8
16
11
12
13
7
2
7
8
7
10
9
15
17
14
18
18
19
20
21
22
REF PART NO. QTY DESCRIPTION
1 47994BLK 1
Hopper
2 44663 2
Hub Cap
3 47983 1
Flow Slide
4 43343 1
Hairpin Agitator
5 43088 2
Washer, 1/4 Std
6 43648 2
Hex Bolt, 1/4-20 x 1-1/2"
7 45165 3
Carriage Bolt 1/4-20 x 2"
8 47141 3
Wing Nut, Nylon 1/4-20
9 49447 1
Control Cable Assembly
(includes items 7 & 8)
10 46503 1
Wheel & Tire Assembly
11 48865 1
Wheel & Tire Assembly /w Drive
12 40904 1 Gearbox Assembly
REF PART NO. QTY DESCRIPTION
13 47124 1
Impeller
14 40903 1
Axle
15 47851 2
Plastic Spacer
16 47985 1
Handle Tube
17 47963 2
Hex Flange Bearing
18 47189 6
Nut, Nylock 1/4"
19 46699 4
Hex Bolt, 1/4-20 x 2"
20 28106 1
Leg Tube
21 49085 1
Frame Tube
22 43501 1
Cotter Pin, 9/64" x 1-1/2"
28075 1
Owner's Manual
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
© 2005 Agri-Fab, Inc.
1 / 1

Agri-Fab 45-03882 User manual

Category
Spreader
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document