45-05311
FORM NO. 45725 (01/24/19)
...................................................................5
ENGLISH ............................................................7
DEUTSCH ..........................................................8
FRANÇAIS .........................................................9
ITALIANO .........................................................10
NEDERLANDS ................................................. 11
ESPAÑOL ........................................................12
PORTUGUÊS ...................................................13
ΕΛΛΗΝΙΚΆ .......................................................14
DANSK ............................................................. 15
NORSK .............................................................16
SVENSKA ........................................................17
SUOMI .............................................................. 18
POLSKI ............................................................19
ČEŠTINA ..........................................................20
MAGYAR ..........................................................21
РУССКИЙ ........................................................22
SLOVENSKO ...................................................23
the fastest way to purchase parts
www.speedepart.com
Page is loading ...
3
REF QTY PART NO DESCRIPTION
1 4 49449 1" Plug
2 1 47141 1/4" Nylon Wing Nut
3 1 69009 Handle
4 8 47189 1/4" Nylock Hex Nut
5 1 45360 Control Cable
6 1 45165 Carriage Bolt
7 6 43648 1/4 X 1-1/2" Hex Bolt
8 2 43088 Small Washer
9 1 48934 Hairpin Agitator
10 1 47994BLK Hopper
11 1 28464 Lower Handle Tube
12 1 45505 Flow Slide
13 1 45504 Impeller
14 2 44101 3/32" Cotter Pin
REF QTY PART NO DESCRIPTION
15 4 R19171616 Large Washer
16 1 24116 Drive Wheel Plate
17 1 48865 Drive Wheel
18 2 45705 Spacer
19 2 47963 Flange Bearing
20 2 46699 1/4 X 2" Hex Bolt
21 1 43501 9/64" Cotter Pin
22 1 46503 Wheel
23 1 68491 Frame Assembly
24 1 28379 1/2" Axle
25 1 69209 Gearbox Assembly
26 1 28463 Stand Tube
1 45725 Owner's Manual
45-05311
MADE IN
USA
WITH GLOBAL COMPONENTS
Customer Care
M-F 7:00 a.m. - 5:00 p.m. CST
800-448-9282
www.agri-fab.com
THANK YOU
FOR YOUR PURCHASE!
Without your product review, we don’t exist.
If you are happy with our quality products & service,
please take just a moment to leave positive feedback and
a short review of our product on our website or your retailer’s website.
Not totally satised?
If you have any issues, don’t hesitate to contact us.
We make mistakes sometimes, but please give us the chance
to make it right before leaving negative feedback against our product.
Page is loading ...
Page is loading ...
Page is loading ...
7
ENGLISH
SAFETY INFORMATION
1. Read the information on the chemical package for
instructions and cautions on handling and applying.
2. Wear eye and hand protection when handling and
when applying lawn or garden chemicals.
3. Never allow children to operate the vehicle.
OPERATION
Do not use powdered lawn chemicals. They do not give a
satisfactory or consistent broadcast pattern.
1. Estimate the size of the area to be covered and
calculate the amount of material required.
2. Set the adjustable stop according to the ow setting
recommended in the application chart on this page.
Also refer to the instructions on the packaging for the
material to be spread.
3. The application chart is calculated for light to heavy
coverage at a vehicle speed of 3 mph, or 100 ft. in 23
seconds. Do not exceed 6 mph.
4. Make sure the control lever is in the "OFF" position.
5. Fill the hopper, breaking up any lumpy fertilizer.
6. Start the spreader in motion and then pull the control
lever forward against the adjustable stop to the "ON"
position.
7. Always move the control lever to the "OFF" position
before turning or stopping.
8. To ensure uniform coverage, make each pass so that
the broadcast pattern slightly overlaps the pattern
from the previous pass. The approximate broadcast
widths for different materials are shown in the
application chart on this page.
9. For rectangular areas, make two passes across
the short ends to create turning areas. For non-
rectangular areas, make two passes around the
entire border.
10. When broadcasting weed control fertilizers, make sure the
broadcast pattern does not hit evergreen trees, owers or
shrubs.
TYPE MATERIAL FLOW SETTING SPREAD WIDTH
FERTILIZER
Granular 3 - 5 2,4 m - 3 m
Pelleted 3 - 5 3 m - 3,6 m
GRASS SEED
Fine 3 - 4 1,8 m - 2,1 m
Coarse 4 - 5 2,4 m - 2,7 m
ICE MELTER 6 - 8 3 m - 3,6 m
APPLICATION CHART
WARNING: Over-inated tires can explode,
causing serious injury. To avoid injury, NEVER
inate tires beyond the maximum pressure
printed on the sidewall of the tire. ALWAYS
use a hand pump to safely inate tires.
MAINTENANCE
1. Oil the free spinning wheel once a year or more often
as needed.
2. Oil the nylon bushings in the frame tube once a year or
more often as needed.
3. Apply a light coating of grease to the gears as needed.
4. Before each use make a thorough visual check of
the spreader for any bolts and nuts which may have
loosened. Retighten any loose bolts and nuts.
5. Make sure the tires are adequately inated. Do not
inate beyond the maximum pressure printed on the
tire.
STORING
1. Empty the spreader after each use, storing left over
material in its original bag.
2. Rinse the inside of the hopper and the exterior of the
spreader and dry off before storing.
3. Store in a clean, dry area.
IMPORTANT: Minor setting adjustments may be necessary
to compensate for humidity and moisture content of the
material.
69115
Deflector Kit
69128
Plastic Grate
40883
Cover
OPTIONAL ACCESSORIES
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
© 2019 Agri-Fab, Inc. Printed In USA
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab, Inc.
809 South Hamilton
Sullivan, IL. 61951
217-728-8388
www.agri-fab.com
/
