Saramonic 10789246 User manual

UHF Wireless

Microphone System

UwMic9

User Manual

Statement

Please read this manual carefully before using and strictly

operate and store in accordance with the instructions. Please

save it for your future reference.

If the user manual can not help you to solve certain problems,

please ask your retailer for help or email us: info@saramonic.

com.

Cautions

1. Do not use the unit under water, don't expose it to rain.

Please store it in a cool, dry place.

2. Please use and store it in normal temperature. Do ot move it

from overheated to supercooled condition frequently as well

as keep away from heat sources such as heater and oven.

3. When using and storing, please pay attention to dust and

moisture.

4. Be careful to violent collision.

5. To avoid acoustical feed-back, do not hold the microphone

close to the loudspeakers.

6. For the best sound pick-up pattern do not hold your hand

against the microphone head.

7. Remove the batteries from the battery compartment when

the device is not used for a long time.

/ 1

CONTENTS

General Introduction.................................................................. 2

Portable Receiver UwMic9-RX9 ............................................... 2

Introduction................................................................................... 2

Product Structure ........................................................................ 2

Attaching Accessories ................................................................ 4

LCD Display Operation Guide ..................................................... 5

Body-pack Transmitter UwMic9-TX9 ....................................... 8

Introduction................................................................................... 8

Product Structure ........................................................................ 8

Attaching Accessories .............................................................. 10

LCD Display Operation Guide ................................................... 11

Hand-held Microphone UwMic9-HU9 ..................................... 14

Introduction.................................................................................14

Product Structure ...................................................................... 14

Setup Guide................................................................................. 15

Plug-on Transmitter UwMic9-TX-XLR9 .................................. 16

Introduction.................................................................................16

Product Structure ...................................................................... 16

Attaching Accessories .............................................................. 18

LCD Display Operation Guide ................................................... 19

Operation Guide ....................................................................... 22

Specification............................................................................. 26

Receiver RX9 ..............................................................................26

Transmitter TX9, HU9 and TX-XLR9 ....................................... 27

Packing list ............................................................................... 28

/ 2

General Introduction

The Saramonic UwMic9 UHF wireless microphone system is

intended for portable wireless operation and can be used in

several environments for applications such as DSLR video, field

recording, broadcast TV, electronic news gathering (ENG), on-

the-spot interviews, and more.

Portable Receiver UwMic9-RX9

Introduction

The Saramonic UwMic9-RX9 is a camera-mountable integrated

wireless receiver. It features a wide switching RF bandwidth, an

easy-to-read LCD display and infrared synchronization between

transmitter and receiver.

Equipped with an auto-scan function, the RX9 can automatically

search for an available transmission frequency.

The selectable output mode allows you to choose the output

signal to be mono or stereo.

Product Structure

①

②

⑤

⑦

③

④

⑥

⑧

⑩ ⑨

⑪

/ 3

①

Antennas

②

Power button

Press to turn on or off the RX9.

③

SET button

Long press the SET button to enter the displayed menu.

Then, short press the SET button to confirm your option or

long press again to exit without saving.

④

POWER indicator

Indicates the battery level as follows:

Green light: Sufficient battery level.

Red light: Low battery level.

⑤

RF indicator and infrared transmitter port

The infrared transmitter port sends the set frequency to a

transmitter.

RF indicator displays the RF input level as follows:

Green light: RF signal is strong.

Red light: RF signal is weak or disconnected.

⑥

+ or – button

Selects functions or values shown on the display.

⑦

LCD display

Display menus, please refer to "LCD Display Operation

Guide" (page 5) for more details.

⑧

Battery compartment

Operates on two AA batteries (not included).

⑨

PHONE jack

It is a 3.5mm diameter and stereo mini headphone jack.

Connect a headphone to monitor the audio output.

Note: Please do not connect a headphone with a mona-

ural mini jack. As this may short-circuit the headphone

jack and distorted sound output.

⑩

OUTPUT jack

Connect the RX9 to a video camera, camcorder, mixer or

amplifier with the supplied output cable.

⑪

Standard cold shoe

/ 4

Attaching Accessories

1

Connect the supplied cable to the output jack.

2

Attach a belt clip. Please Refer to "Attaching Accessories"

(page 10).

3

Attach the shoe mount adapter.

①



Plug the supplied cable into

the OUTPUT jack.

②

For a secure connection, turn

to lock the connector.

①

②

①

③

②

①

Please attach the belt clip

upside-down before attach-

ing the shoe mount adapter.

②

Push the bottom of the belt

clip to make some space

between the belt clip and the

receiver.

③

Align the belt clip with the two

vertical grooves on the shoe

mount adapter and insert the

adapter in the direction of the

arrow.

④

Push the shoe mount adap-

ter in fully until the belt clip

fits into the horizontal groove

on the adapter holds.

/ 5

LCD Display Operation Guide

Home screen. If no operation is performed for 20 seconds on

the other screens, the display will automatically return to the

home screen.

①

Group icon

Indicates the power of group A is turned off.

Indicates the power of group A is turned on.

②

RF level indicator

Indicates the current reception level.

③

Battery level indicator

Displays the battery level. Please replace both batteries

immediately when the indicator starts flashing.

④

Name of the channel group

⑤

Current channel

Displays the current channel number.

⑥

Audio input level meter

Displays the audio input level.

2

Power key. Long press the SET button to unlocked or locked

the power key. Lock the power key to prevent the receiver being

turned off unwittingly while using.

• Unlocked: Long press the power key to turn the receiver on

or off (System default).

• Locked: The receiver will not be turned off even after

pressing the power key.

① ② ② ③

④

⑤

⑥

①

1

/ 6

Note: If the batteries are removed and reinserted while the

power key is set to Locked, the lock state of the Power key

will not be changed. You can turn on the receiver by long

pressing the power button.

3

Output mode. The output mode can be selected to mono or

stereo. When the output mode is mono, the audio from left and

right channel will be mixed. When it is stereo, the left (Group

B) and right (Group A) audio channel output will be separated.

System default is mono.

4

9

Power of the Group. When you only use one group signal, please

turn off the other group to save battery. To save battery, system

default of the Group B is power off while the Group A is power

on.

When operating two transmitters simultaneously, please set

each transmitter to a different group to prevent interference or

noise.

5

10

Select channel. Details of operation, please refer to "Manually

setting the receiver channel" (page 24).

/ 7

6

11

Set output volume. Set the volume of output audio within the

range 0 to 30. The setting is retained even after the power is

turned off. Default is 30.

7

12

Auto scan function. Automatically scan an available and clear

channel. Details of operation, please refer to "Using the auto

scan function" (page 23).

8

Group

Matc h with TX

ettings

13

Group

Matc h with TX

ettings

Infrared matching function. Match the receiver and transmitter

via infrared. Details of operation, please refer to "Match the

channel of receiver and transmitter" (page 24).

14

Set backlight. Set the backgroud LED light to ON or Delay 60 /30

/10 seconds or OFF. Default is "Delay 10s."

15

Restore settings. Confirm it then the parameters of RX9 are

restored to their factory default settings.

/ 8

①

⑦

⑧

⑨

②

③

⑤

④

⑥

16

Version of the UwMic-RX9.

17

Serial Number.

Body-pack Transmitter UwMic9-TX9

Introduction

This transmitter is a compact transmitter that employs a

crystal-controlled PLL synthesizer. It is equipped with a muting

function and a locking-type microphone input connector. The RF

power output can be switched among high, middle and low.

Product Structure

/ 9

①

Antenna

②

AUDIO indicator / IR (infrared detector)

AUDIO indicator: Indicates the audio input level.

IR (infrared detector): Receives the frequency from the receiver.

Solid Green: Audio input level is appropriate.

Flashing Red: Audio is muted (i.e., disabled).

For details on setting the mute function, please refer to "Set

Mute key" (page 12).

③

POWER indicator

Indicates the battery level as follows:

Solid Green: Sufficient battery level.

Solid Red: Low battery.

④

Audio input connector (3.5mm locking-type plug)

Connect to the supplied lavalier microphone.

⑤

+ or – button

Selects functions or values shown on the display.

⑥

Battery compartment

Accepts two AA batteries (alkaline, nickel metal hydride,

or lithium batteries).

⑦

Power / Mute button

Function Operation

Power ON Press button for one second or longer

Power OFF Press button until it turns off

Mute ON

Short press button

Mute OFF

⑧

SET button

Long press the SET button to enter the displayed menu.

Then, short press the SET button to confirm your option or

long press again to exit without saving.

⑨

LCD display

Display menus, please refer to "LCD Display Operation

Guide" (page 11) for more details.

/ 10

2

Connect the mcirophone.

For a secure connection, turn

to lock the connector.

Note: Please turn off the

transmitter before attaching

or removing the microphone.

1

Attach a belt clip.

Insert one end of the belt clip

into one of two holes on either

side of the transmitter, and

then insert the other end into

the hole on the other side.

Attaching Accessories

/ 11

LCD Display Operation Guide

Home screen. If no operatIon is performed for 20 seconds on

the other screens, the display will automatically return to the

home screen.

①

RF transmission power indicator

Indicates the current transmission power level.

For details on setting the level, please see "Select RF power

level" (page 12).

②

Channel group indicator

Indicates the channel group.

③

Mute indicator

Mute OFF Mute ON

④

Battery level indicator

Displays the battery level. Please replace both batteries

immediately when the indicator starts flashing.

⑤

Name of the channel group

⑥

Channel and frequency

Indicate the current channel and frequency.

⑦

The status of Power / Mute button.

1

2

⑤

⑦

⑥

①

① ② ③ ④

①

Menu display section. Displays various functions. Press the

+ or - button to switch functions.

Set Power key. Select Unlocked or Locked.

Set "Locked" to lock the power button to prevent the unit

being turned off or muted unwittingly while using. Default is

"Unlocked."

/ 12

3

Select Channel. Long press the SET button to enter the menu.

Use the "+" and "-" to select the channel you need and shot press

the SET button to confirm.

4

Select Group. You can choose "A" or "B" channel group. Each

group has 96 channels. Default is 'Group A."

5

Select RF power level. You can set the transmitted RF power to

High, Middle or Low. Default is "High."

6

Set Mute key. If you want to mute the audio, please select

"Enable" first and then short press the power button. Default is

"Enable."

/ 13

7

IR Match. Set to match with the receiver. The screen will display

"Matching" when in process. After successful matching, it will

indicate "Sync finished."

8

Set Backlight. Select ON, OFF or Delay 10 / 30 /60 seconds.

Default is "Delay 10s."

9

Restore default setting.

10

Version of the UwMic9-TX9.

11

Serial Number.

/ 14

②

Power / Mute button

Power: Long press to turn on/off the HU9.

Mute: Short press the button while transmitting, the audio will

be muted. Press it again to restore the audio output.

Note: In muting, the audio signal is not output but an RF

signal is still transmitted.

③



Antenna

⑤

①

LCD screen

A. Channel Groups.

Two channel groups: A and B.

Each group has 96 channels.

B. Channel number.

C. Battery level indicator.

D. MUTE. Audio is muted.

This LCD display indicates it is

operating on channel 96 of group A.

①

②

③

④

A B

C D

Hand-held Microphone UwMic9-HU9

Introduction

Saramonic HU9 is a handheld wireless UHF microphone

transmitter features a compact metallic body, an easy-to-read

LCD display, a RF power switch and a PLL synthesizer. The

broadcast quality microphone will capture crystal clear and rich

sound. It has a built-in antenna, a muting function and power lock

function. The channel of HU9 is synced up with the receiver via

infrared.

Product Structure

/ 15

④



Operation panel

ON

OFF

HIGH

LOW

LOCK

UHF

RF

B

A

C

A. Infrared detector. Receives

the frequency set on the

receiver.

B. Lock switch. Set to ON will

lock the power button. It will

prevent the power being

turned off inadvertently

during transmission.

Note: The lock switch will

not lock the mute function.

C. RF power. Set the transmit

output level to HIGH or LOW.

⑤



Battery compartment

Operates on two AA batteries (not included).

You could use alkaline, lithium or nickel metal hydride batteries.

Setup Guide

1

Install the batteries. Refer to "UwMic9-HU9" (page 22).

2

(Option) Set the lock switch to ON or OFF.

3

(Option) Set the RF power to HIGH or LOW. The transmit

power level varies depending on the model.

4

Press the power button to turn on the HU9.

5

Turn on the receiver UwMic9-RX9 and sync with the

transmitter HU9. Details of operation, please refer to "For

HU9" (page 25).

6

When sync successfully, the screen of HU9 will show the

group and channel same as the receiver.

7

Close the grip in the direction of the arrows.

8

Now it is ready to use.

/ 16

①

XLR audio input jack

Connects to an XLR microphone or audio devices with line

output.

②

+48V power indicator

Lights up when the +48V phantom power is on.

③

POWER indicator

Indicates the battery level as follows:

Solid Green: Sufficient battery level.

Solid Red: Low battery.

Plug-on Transmitter UwMic9-TX-XLR9

Introduction

The Saramonic TX-XLR9 is a compact XLR plug-on type

transmitter features a wide switching RF bandwidth, an easy-

to-read LCD display, +48V phantom power and mute function. It

is suitable for portable wireless operation and can be used in

a wide range of applications such as DSLR video, broadcast TV,

ENG and more.

Product Structure

⑧

⑨

②

③

①

⑦

⑥

④

⑤

/ 17

④

AUDIO indicator / IR (infrared detector)

AUDIO indicator: Indicates the audio input level.

IR (infrared detector): Gets the frequency from the receiver.

Solid Green: Audio input level is appropriate.

Flashing Red: Audio is muted (i.e., disabled). For details on

setting the mute function, please refer to "Set Mute key"

(page 20).

⑤

LCD screen

Displays menus, please refer to "LCD Display Operation

Guide" (page 19) for more details.

⑥

Power / Mute button

Turns the power or mute function to on or off.

Function Operation

Power ON Press the button for one second or longer

Power OFF Press the button until it turns off

Mute ON

Short press the button

Mute OFF

⑦

SET button

Long press the SET button to enter the displayed menu.

Then short press the SET button to confirm your option or

long press again to exit without saving.

⑧

+ or – button

Selects functions or values shown on the display.

⑨

Battery Compartment

Operates on two AA batteries (alkaline, nickel metal hydride,

or lithium batteries). For details on how to insert batteries,

please refer to "Install the batteries" (page 22).

/ 18

2

Disconnect a microphone or XLR cable.

Press the release button and pull the microphone or XLR cable

out carefully in the direction of arrow.

Note: Please turn off the transmitter before attaching or

removing the microphone.

1

Attach a microphone or XLR cable.

Push the microphone or cable connector into the XLR audio

input jack of the TX-XLR9 until it clicks into place.

Attaching Accessories

Microphone or XLR cable

Release button

Page is loading ...

Saramonic 10789246 User manual

Saramonic 10789246 User manual

Related papers

Other documents