Page is loading ...
110 Telecom Module
100 Pair Capacity
With Security Panel Loop
C-0441
TM
CHANNEL VISION
© 2003 Channel Vision Technology
234 Fischer Avenue · Costa Mesa, CA 92626
(714) 424-6500 · (800) 840-0288 · (714) 424-6510 fax
www.channelvision.com · email: sales @ channelvision.com
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
CHANNEL VISION
Limited Warranty
Channel Vision Technology will repair or replace any defect in
material or workmanship which occurs during normal use of this
product with new or rebuilt parts, free of charge in the USA, for two
years from the date of original purchase. This is a no hassle warranty
with no mail in warranty card needed. This warranty does not cover
damages in shipment, failures caused by other products not supplied
by Channel Vision Technology, or failures due to accident, misuse,
abuse, or alteration of the equipment. This warranty is extended only
to the original purchaser, and a purchase receipt, invoice, or other
proof of original purchase date will be required before warranty
repairs are provided.
Mail in service can be obtained during the warranty period by calling
(800) 840-0288 toll free. A Return Authorization number must be
obtained in advance and can be marked on the outside of the shipping
carton.
This warranty gives you specific legal rights and you may have other
rights (which vary from state to state). If a problem with this product
develops during or after the warranty period, please contact Channel
Vision Technology, your dealer or any factory-authorized service
center.
500-007 rev B
2
The model C-0441 is a versatile, high capacity phone distribution panel
that mounts a standard 100 pair 110-type cross-connect block on a
structured wire module. A switch based security panel loop is provided
(more reliable than the typical RJ-31x jack).
1) Route first 12 cables
as shown
Wiring the C-0441 for typical telephone use.
(24 telephone drops of 4 lines each.)
2) Remove jacket from far left cable.
(Use sheath cutting tool.)
3
Bed rm #2Bed rm #2
3) Untwist and position wires in slots 1-8 (extreme left).
Follow color code as shown. Note that the
white with color stripe wire is to the left of solid color.
3a) Identify this cable and fill in the
upper left slot on the wiring list card.
4) Repeat for second cable.
Bed rm #2Bed rm #2
OfficeOffice
Bed rm #2Bed rm #2
OfficeOffice
Cat-3 or Cat 5 cables
from phone jacks
around the house.
The wiring list card has two sides.
Use the side with 12 boxes.
Push the wires far into the
block so they will stay in place.
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
4) Repeat for cables 3-12.
5) Use 110 punch-down tool to seat
and trim all wires
Note position of cutter
6) Use 4-pair impact tool to seat
110 blocks. Seat all blocks
on top two rows.
Start with 8-pin (4-pair)
110 blocks at far left.
Note that some connectors have
10 pins (5 pair). Note the
sequence of connectors.
Note color codes.
7) Wire the bottom two rows in the
same fashion. Slide wiring lists
into holders and snap into the frame.
You will now have up to 24 phone drops,
ready to cross-connect.
Bed rm #3Bed rm #3
OfficeOffice
Kitchen northKitchen north
Bed rm #2Bed rm #2
Kitchen EastKitchen East
Entry Entry
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Master deskMaster desk
Master bdrm TVMaster bdrm TV
Master bathMaster bath
Slide into plastic holder
Snap plastic holder between rows.
4
5
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
Sequence of connectors
8-pin 10-pin8-pin 8-pin 8-pin 8-pin
Caution: it is easy to place the
connectors upside down. Use
care when seating connectors.
2
The model C-0441 is a versatile, high capacity phone distribution panel
that mounts a standard 100 pair 110-type cross-connect block on a
structured wire module. A switch based security panel loop is provided
(more reliable than the typical RJ-31x jack).
1) Route first 12 cables
as shown
Wiring the C-0441 for typical telephone use.
(24 telephone drops of 4 lines each.)
2) Remove jacket from far left cable.
(Use sheath cutting tool.)
3
Bed rm #2Bed rm #2
3) Untwist and position wires in slots 1-8 (extreme left).
Follow color code as shown. Note that the
white with color stripe wire is to the left of solid color.
3a) Identify this cable and fill in the
upper left slot on the wiring list card.
4) Repeat for second cable.
Bed rm #2Bed rm #2
OfficeOffice
Bed rm #2Bed rm #2
OfficeOffice
Cat-3 or Cat 5 cables
from phone jacks
around the house.
The wiring list card has two sides.
Use the side with 12 boxes.
Push the wires far into the
block so they will stay in place.
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
4) Repeat for cables 3-12.
5) Use 110 punch-down tool to seat
and trim all wires
Note position of cutter
6) Use 4-pair impact tool to seat
110 blocks. Seat all blocks
on top two rows.
Start with 8-pin (4-pair)
110 blocks at far left.
Note that some connectors have
10 pins (5 pair). Note the
sequence of connectors.
Note color codes.
7) Wire the bottom two rows in the
same fashion. Slide wiring lists
into holders and snap into the frame.
You will now have up to 24 phone drops,
ready to cross-connect.
Bed rm #3Bed rm #3
OfficeOffice
Kitchen northKitchen north
Bed rm #2Bed rm #2
Kitchen EastKitchen East
Entry Entry
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Master deskMaster desk
Master bdrm TVMaster bdrm TV
Master bathMaster bath
Slide into plastic holder
Snap plastic holder between rows.
4
5
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
Sequence of connectors
8-pin 10-pin8-pin 8-pin 8-pin 8-pin
Caution: it is easy to place the
connectors upside down. Use
care when seating connectors.
7) Cross-connect 4 phone lines to all phone jacks.
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
From Teleco
To security panel
Blue/white = to panel TIP
Blue = to panel RING
Orange/white = from panel TIP
Orange = from panel RING
Snake wires back and forth to connect all phones to lines 1-4. Cross-connect wire
can be purchased at electrical supply houses or make by stripping back a length of
category cable.
NOTE: When you punch the wires down, remember to use the non-cutting
blade on 110 punch-down tool.
8) Connect to Security panel. Connect to Telco last.
In the normal position, the switch
will route line 1 to the security
panel. In alarm mode, the panel
will “seize” line one, disconnect
it from the rest of the house
and dial the alarm central
station using line.
If no security panel is used,
the switch should be
moved to the bypass
position.
6
7
Bed rm #3Bed rm #3
OfficeOffice
Kitchen northKitchen north
Bed rm #2Bed rm #2
Kitchen EastKitchen East
Entry Entry
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Master deskMaster desk
Master bdrm TVMaster bdrm TV
Master bathMaster bath
Bed rm #3 NoBed rm #3 No
Bed rm #3 SoBed rm #3 So
BasementBasement
Garage #1Garage #1
Lndry rmLndry rm
Garage #2Garage #2
Bed rm #4Bed rm #4
Bed rm #5Bed rm #5
Bed rm #6Bed rm #6
Media ctr #1Media ctr #1
Media ctr #2Media ctr #2
Liv rmLiv rm
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
Note slack in wire (service loop)
allows for changes in future.
Completely
wired panel
Bed rm #3Bed rm #3
OfficeOffice
Kitchen northKitchen north
Bed rm #2Bed rm #2
Kitchen EastKitchen East
Entry Entry
Back porch #1Back porch #1 Master bed rtMaster bed rtMaster bed leftMaster bed left
Master deskMaster desk
Master bdrm TVMaster bdrm TV
Master bathMaster bath
Bed rm #3 NoBed rm #3 No
Bed rm #3 SoBed rm #3 So
BasementBasement
Garage #1Garage #1
Lndry rmLndry rm
Garage #2Garage #2
Bed rm #4Bed rm #4
Bed rm #5Bed rm #5
Bed rm #6Bed rm #6
Media ctr #1Media ctr #1
Media ctr #2Media ctr #2
Liv rmLiv rm
C-0441
CHANNELVISION
Central
TM
From Telco
To System
To Alarm Panel
T
R
In
Out
Alarm Bypass
T
R
/
