One For All urc 9990 mosaic User manual

Universal Touch Screen Remote . . . . . . . . . . . . . P.2

URC-9990

F

D

UK

User guide p.2

Bedienungsanleitung S.44

Mode d’emploi p.86

ONE FOR ALL MOSAIC URC-9990

DD-0201

701571

Table Of Contents

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALLING BATTERIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

LOW-BATTERY INDICATOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

USING THE TOUCH SCREEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

DEVICE SET-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B

Y BRAND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

B

Y SEARCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

B

Y CODE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

D

ELETE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

N

EW CODES (IN CASE OF UPGRADE) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

PERSONALIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

M

ACROS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

M

OVE KEY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

L

EARN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

L

ABEL KEYS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

K

EY MAGIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

V

OLUME LOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

V

IEW/DELETE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

H

OME THEATER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

SYSTEM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

U

PGRADE (ADDING NEW CODES) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

S

OUND ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

L

OCK SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

U

SER RESET. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

L

ANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

A

BOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

CUSTOMER SERVICE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

T

ELEVISION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

V

IDEO RECORDERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135

S

ATELLITE RECEIVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138

C

ABLE CONVERTERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

V

IDEO ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

CD/M

INI DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141

P

HONO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

H

OME AUTOMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

A

MPLIFIERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

A

MP/TUNERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142

C

ASSETTE PLAYERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

L

ASER DISC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

D

AT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

D

VD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

2 www.oneforall.com

www.oneforall.com 3

Introduction

Your ONE FOR ALL MOSAIC is designed to let you use one remote to operate your Video and Audio

equipment; any device designed to be operated by an infrared signal.This also includes those devices

which operate over 100 kHz.You can choose any combination of 15 devices you would like to operate.

The ONE FOR ALL MOSAIC comes available with the world’s largest and most efficient database of

infrared codes for device compatibility.It is further enhanced by ONE FOR ALL’s patented upgrade-

ability. Also,what makes the MOSAIC even more unique is the "Learning" feature which allows you

to customise any of the special functions of your original remote control onto the keypad of your new

ONE FOR ALL.

The following pages explain in simple steps how to customize the ONE FOR ALL MOSAIC to your

home entertainment needs.

Installing Batteries

Your MOSAIC needs 4 new "AA/LR6" alkaline batteries .

1. Remove the battery cover from the back of the ONE

FOR ALL MOSAIC by pressing down on the tab.

2. Match the batteries to the + and – marks inside the

battery case,then insert the batteries.

3. Press the battery cover back in place.

Low-Battery Indicator

Whenever the batteries need replacement,

the MOSAIC will emit a "beep sound" (even if the

sound is turned off).The MOSAIC will indicate this

as well on the top portion of the screen with a

"Battery Low" message.

At this point,only the control functions will work

and all of the MOSAIC’s DEVICE SETUP and PER-

SONALIZATION parameters will be disabled to pre-

vent accidental loss of any entered commands

should the batteries run out.

Simply replace the batteries as soon as possible.

Press any IR key and the MOSAIC will be restored

to its full functionality,complete with your favourite

settings.

Low Battery

Indicator

1 2 3

4 5 6

7 8 9

0

-/--

AV PWR

CBLTV VCR

THEATERSetup

|| Battery Low ||

Using the touch screen

MOSAIC features a Touch Screen that responds to touch

commands,whether you use the supplied Stylus or your

finger tip.Each time you tap on the screen,you’ll see the

LED blink and hear a beep tone,which serve as visual

and audio confirmation of your command.

After 20 seconds of inactivity,MOSAIC will turn off the

LCD screen to conserve battery life.

NOTE: By pressing the ? key you will obtain additional information about

the displayed menu.

1 2 3

4 5 6

7 8 9

0

-/--

AV PWR

CBLTV VCR

THEATERSetup

R

URC - 9990

1 2 3

4 5 6

7 8 9

0

-/--

AV PWR TV/VCR PWR

CBLTV VCR CBLTV VCR

THEATERSetup THEATERSetup

Tap on

Current

active

device

Current

active

device

Tap on scroll arrow

to see other devices.

Remote Control

Keys for active

device

Tap on pages

to see more

Remote Control

Keys.

Phono Jack

(for future

computer

connection)

Stylus

and

Housing

IR Signal

Emitters

Piezo Speaker

(for Audio

Confirmation)

Contrast

Control

(for

Touch Screen)

Battery

Cover

Tab

(to release

Battery Cover)

IR Learning

Eye

R

URC - 9990

LED

(for Visual Confirmation)

VOLUME

Up/Down

MUTE

On/Off

Touch Screen

(Soft Keys)

(Hard Keys)

BACKLIGHT

On/Off

CHANNEL

Up/Down

4 www.oneforall.com

Device Setup

BY BRAND

The easiest way to add devices to MOSAIC is to perform a setup by manufacturer brand.With this

method you select a device to add,select the brand you own,and MOSAIC automatically finds the

correct manufacturer’s code to correctly control the device.

Example:to Set-Up your Video Recorder (brand:Nokia):

NOTE: To return to a previous menu,tap on the ESC key.To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds. For help,tap the ? key.

1 2 3

4 5 6

7 8 9

0

-/--

AV PWR

THEATERSetup

Tap on

CBL

VCR

DEVICE SETUP

PERSONALIZATION

SYSTEM

SETUP

Welcome to Setup!

What would you like to configure?

Esc ?

Tap on

BY BRAND

BY SEARCH

BY CODE

DELETE

DEVICE SETUP

Welcome to Device Setup!

What method

would you like to use?

Esc ?

Tap on

CBL SATTV

DVD LDVCR

AMP CDTUN

DAT PHOTAPE

HOMEV.ACC

BRAND SET

Select the device.

Esc

Tap on

OTHER

A-E F-M N-R S-ZA-E

ASAAdventura

AVP

Adelsound

Adventura

Adyson

Aiwa

Akai

Akiba

Akura

Alba

BRAND SET

VCR

Use the letters or the bar

to scroll to your brand.

Esc OK

Scroll

Bars

Alphabet Keys

OTHER

A-E F-M

S-Z

F-MN-R

NEC

Neckermann

Nesco

Nikkia

Nokia

Nordmende

Oceanic

Okano

Olympus

Optimus

BRAND SET

VCR

Use the letters or the bar

to scroll to your brand.

Esc OK

First,

tap on

brand

Then, tap on

www.oneforall.com 5

• To relabel the device key,tap on the YES key and you will see the LABEL Menu (see explanation

on page 25 step 6).

• To keep the label the same,tap on the NO key.

You will see a confirmation screen that says the key has been successfully programmed.To

program another device,tap on the ESC key.To return to the Device Screen,press on ESC or

MUTE for at least 2 seconds.

To test remote control of the newly-added device,tap on its key on the Device Selection Strip.Try

using the Hard Keys to adjust volume and change channels.Try tapping on the Page Arrows to access

other remote control functions and then try tapping on the soft keys on each page to test them.

NOTE: Remember to press the correct device key before operating your device.Only one device

(CD, amplifier, cassette,etc.) can be assigned to a device key. If your original remote operates

more than one device (for example,a receiver, CD player and cassette player in one remote),

you need to set up each device separately.

6 www.oneforall.com

Test

1

PWR

VCR 1

VCR 2

VCR 3

VCR 4

VCR 5

VCR 6

BRAND SET

Nokia

Your brand has multiple

types; use the scroll bars

to try each one in turn.

Esc OK

ADD

REPLACE

BRAND SET

Would you like to

ADD the device or REPLACE

it with an existing one?

Esc ?

Tap on

if 1

st

VCR

Tap on

if 2

nd

VCR

Press OK to confirm.

BRAND SET

Esc OK

CBL VCR VCR

Tap on

Relabel the device?

BRAND SET

CBL VCR VCR

YES NO

SETUP BY SEARCH

As an alternative method,you can use MOSAIC’s search program to find the correct manufacturer’s

codes to set up your entertainment devices.With this method you first select a device you want to

add,then you perform a code test,advancing through one or more types,to find the one that works.

Example: to use the search method for your television:

Tap on the OK key to confirm your choice.MOSAIC will ask if you want to relabel the newly-added

device.

• To relabel it,tap on the YES key and you will see the LABEL Menu (see explanation on page 25

step 6).

• To keep the label the same,tap on the NO key.

You will see a confirmation screen that says the key has been successfully programmed.To

program another device,tap on the ESC key.To return to the Device Screen,press on ESC or

MUTE for at least 2 seconds.

To test remote control of the newly-added device,tap on its key on the Device Selection Strip.Try

using the Hard Keys to adjust volume and change channels.Try tapping on the Page Arrows to access

other remote control functions and then try tapping on the soft keys on each page to test them.

www.oneforall.com 7

CBL SATTV

DVD LDVCR

AMP CDTUN

DAT PHOTAPE

HOMEV.ACC

SEARCH

Select the device.

Esc

Tap on

BY BRAND

BY SEARCH

BY CODE

DELETE

DEVICE SETUP

Welcome to Device Setup!

What method

would you like to use?

Esc ?

Tap on

ADD

REPLACE

SEARCH

Would you like to

ADD the device or REPLACE

it with an existing one?

Esc ?

Tap on

if 1

st

TV

Tap on

if 2

nd

TV

PREV NEXT

Test

1

PWR

SEARCH

Use the test keys to find

your device type.

Press OK to save.

Esc OK

TV

First, tap on

To check

previous code,

tap on

If device does not

respond, tap and

repeat test.

SETUP BY CODE

Find the code for your device in the Set-Up Code section (starting on page 128).Codes are listed by

device type and brand name.The most popular code is listed first.Make sure your device is switched

on (not in standby).Newly captured Manufacturer’s codes are available for customer access on our

web site www.oneforall.com.

1. Tap on Setup key (upper left corner).

2. Tap on DEVICE SETUP.

NOTE: To return to a previous menu,tap on the ESC key.To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help, tap the ? key.

3. Tap on the OK key to confirm your choice.MOSAIC will ask if you want to relabel the newly-added

device.

• To relabel it,tap on the YES key and you will see the LABEL Menu (see explanation on page 25 step 6).

• To keep the label the same,tap on the NO key.

You will see a confirmation screen that says the key has been successfully programmed.To

program another device,tap on the ESC key.To return to the Device Screen,press on ESC or

MUTE for at least 2 seconds.

To test remote control of the newly-added device,tap on its key on the Device Selection Strip.Try

using the Hard Keys to adjust volume and change channels.Try tapping on the Page Arrows to access

other remote control functions and then try tapping on the soft keys on each page to test them.

CLEAR

CODE SETUP

Device Code

1234

Enter the 4 digit code,

press OK to save.

Esc OK

1 2 3

4 5 6

7 8 9

0

Then tap on

First,

enter

code.

page 128-143

CLEAR

CODE SETUP

Device Code

_

Enter the 4 digit code,

press OK to save.

Esc OK

1 2 3

4 5 6

7 8 9

0

ADD

REPLACE

CODE SETUP

Would you like to

ADD the device or REPLACE

it with an existing one?

Esc ?

Tap on

if 1

st

TV

Tap on

if 2

nd

TV

CBL SATTV

DVD LDVCR

AMP CDTUN

DAT PHOTAPE

HOMEV.ACC

CODE SETUP

Select the device.

Esc

Tap on

BY BRAND

BY SEARCH

BY CODE

DELETE

DEVICE SETUP

Welcome to Device Setup!

What method

would you like to use?

Esc ?

Tap on

8 www.oneforall.com

DELETING A DEVICE

If you no longer use a certain device or it has been incorrectly added to the Device Selection Strip, use

the following procedure to delete it from MOSAIC’s memory.

1. Tap on Setup key (upper left corner).

2. Tap on DEVICE SETUP.

NOTE: To return to a previous menu,tap on the ESC key.To return to last-displayed Device

Screen, press and hold down ESC for at least 2 seconds.For help, tap the ? key.

3. Tap on the DELETE key.You will see the DELETE DEVICE Menu which shows the current

Device Selection Strip.

4. Using the Device Selection Strip,tap the device key you want to delete.If needed,tap the

left/right scroll arrows to display other device choices.When you have selected a device,it will

become highlighted as YES and NO keys appear.

• To delete the selected device,tap on the YES key.You will see a confirmation screen that says

the key has been successfully deleted.To delete another device,tap on the ESC key to return to

the DELETE DEVICE Menu,or press down on ESC or MUTE for at least 2 seconds to return to

the last-displayed Device Screen.

• To cancel deleting the selected device,tap on the NO key.MOSAIC will return to the Device

Selection Strip with no devices selected to start the process over.If you’re done,tap on the ESC

to return to the DEVICE SETUP Menu,or press down on ESC or MUTE for at least 2 seconds

to return to the last-displayed Device Screen.

Which device would you

like to delete?

DELETE DEVICE

Esc OK

CBLTV VCR

BY BRAND

BY SEARCH

BY CODE

DELETE

DEVICE SETUP

Welcome to Device Setup!

What method

would you like to use?

Esc ?

Tap on

www.oneforall.com 9

NEW CODES

NOTE: This section only applies after you have performed a download of new device codes

(see SYSTEM – UPGRADE on page 36).

NOTE: Make sure the device you want to add is turned on (not in standby).

After downloading,MOSAIC will store the new device codes in memory.An additional soft key,

labelled NEW CODES,will appear on the DEVICE SETUP Menu which you will use to find a working

code for a selected device.

1. Tap on Setup key (upper left corner).

2. Tap on DEVICE SETUP.

3. Tap on the NEW CODES key.You will see the UPGRADE Test Menu.

NOTE: To return to a previous menu,tap on the ESC key.To return to last-displayed Device

Screen, press and hold down ESC for at least 2 seconds. For help,tap the ? key.

4. Tap on the first code in the list (e.g.,TV 1),aim MOSAIC at the desired device (e.g.,television),

and tap on the PWR key. The device should turn off.If it does not respond,tap on the next code

in the list (e.g.,TV 2),then tap on the PWR key again.If the device still does not respond,repeat

this process by testing each code until you find one that works.

NOTE: Depending on your download, the code list may include more than one device type.

5. To save a code that works,tap on the OK key.You will see the UPGRADE ADD/REPLACE menu

that lists two choices.

Test

1

PWR

TV1VCR 2

TV2

TV3

TV4

TV5

VCR1

VCR2

VCR3

VCR4

VCR5

UPGRADE

Use the scroll bar to try

each one in turn.

Esc OK

Tap on

BY BRAND

BY SEARCH

BY CODE

DELETE

NEW CODES

DEVICE SETUP

Welcome to Device Setup!

What method

would you like to use?

Esc ?

Tap on

10 www.oneforall.com

• Use the ADD key when setting up a new device (e.g.,a DVD player) that is not currently on

the Device Selection Strip (if needed,refer to USING THE TOUCH SCREEN – on page 4).The

remaining instructions assume you will be adding a new device.

• Use the REPLACE key when replacing a device (e.g.,a TV set) that is currently on the

Device Selection Strip.

6. Tap on the ADD key to add the device to MOSAIC’s memory.You will see the default device label

being added to the Device Selection Strip.

NOTE: If you tap on the REPLACE key instead,MOSAIC will ask you to select the device to be

replaced and,after your selection,if you want to relabel it.However, if the device to be

replaced has programmed keys,MOSAIC will first ask if you want to keep or clear the settings.

7. Tap on the OK key to confirm your choice.MOSAIC will ask if you want to relabel the newly-

added device.

• To relabel it,tap on the YES key and you will see the LABEL Menu (see explanation

on page 25 step 6).

• To keep the label the same,tap on the NO key.

8. You will see a confirmation screen that says the key has been successfully programmed.To pro-

gram a function of the same type,tap on the ESC key. To return to the Device Screen,press on

ESC or MUTE for at least 2 seconds.

9. To test remote control of the newly-added device,tap on its key on the Device Selection Strip.Try

using the Hard Keys to adjust volume and change channels.Try tapping on the Page Arrows to

access other remote control functions and then try tapping on the soft keys on each page to test

them.

10. If desired,repeat all steps to add other devices that appeared in the new codes list of step 3.

Test

1

PWR

TV1VCR 2

TV2

TV3

TV4

TV5

VCR1

VCR2

VCR3

VCR4

VCR5

UPGRADE

Use the scroll bar to try

each one in turn.

Esc OK

Tap on

ADD

REPLACE

UPGRADE

Would you like to

ADD the device or REPLACE

it with an existing one?

Esc ?

www.oneforall.com 11

Personalization

MACROS

MOSAIC includes a powerful Macro feature that memorizes and plays back a series of key strokes at

any time with the tap of one key.Up to 21 macros can be defined,each containing a maximum of 32

keystrokes.Once defined,a macro must be placed on a Device Screen to be used.MOSAIC allows

placement of up to four “global”macro keys across the top of every Device Screen.Also,you may place

additional macros in specific Device Screens using empty locations or by overriding existing key func-

tions.

ADDING A MACRO

As an instruction aid,we’ll create an example “Power On”macro that turns on the Cable Box and TV

power and then tunes in a favorite channel in this exact order:

1. Select the Cable Box and power it on.

2. Add a 2-second delay.

3. On the Cable Box,select channel 28.

4. Select the TV and power it on.

6. Add a 1-second delay.

7. On the TV,select channel 3 to view the modulated signal from the Cable Box.

Each command counts as one macro keystroke,except when selecting a device key which counts as

two.In this example,the total keystroke count is eleven.

NOTE:Adding delays allow devices to power up to their full operating state. In most cases,1 to

2 seconds is sufficient,but MOSAIC will accept up to 8 seconds and only count it as one key-

stroke.

12 www.oneforall.com

1. Tap on Setup key (upper left corner).

2. Tap on PERSONALIZATION.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

3. Tap on the MACROS key.You will see the MACROS Menu.

4. Tap on the ADD key.You will see the ADD MACROS Menu.

5. Tap on an open Macro key (i.e.,a macro key that is not labelled).You will see the ADD MACROS

Screen (as shown below) which looks similar to a Device Screen.

6. At this point,we’ll record the example keystrokes listed on page 12.But first make sure the Cable

Box and TV are turned off (in standby).

a. Tap on the CBL key on the Device Selection Strip.

b. Tap on the PWR key.

c. Tap on the DELAY key twice for 2-second delay.

NOTE: Each DELAY keystroke is equal to 1 second.

d. Tap on the 2 key followed by the 8 key to enter channel 28.

e. Tap on the TV key on the Device Selection Strip.

f. Tap on the PWR key.

g. Tap on the DELAY key once for 1-second delay.

h. Tap on the 0 key followed by the 3 key to enter channel 3.

i. Aim MOSAIC at the Cable Box/TV and tap on the TEST key.You should see the LED blink as

commands are sent to power on the Cable Box and tune it to channel 28,followed by TV power

on and tuning it to channel 3.If the macro did not work correctly,tap on the CLEAR key and

repeat steps 6a through 6i.

ADD MACROS

Select a Macro key.

Esc

Tap on

an open

key

ADD

VIEW

COPY

DELETE

DELETE ALL

MACROS

Program a sequence of

keystrokes onto one key.

Esc ?

Tap on

1 2 3

4 5 6

7 8 9

0

-/--

AV PWR

ADD MACROS

Begin recording the

keystrokes.

Esc

CBLTV VCR

www.oneforall.com 13

7. To save the macro,tap on the OK key.You will see the ADD MACROS Screen (as shown below).

8. To label the saved macro,tap on the YES key.You will see the ADD MACROS Label Screen.

Follow the procedure that is similar to the one starting with step 3 on page 25 to label the macro

as TV On and tap the OK key when you’re done.

NOTE: If you tap on the NO key, the macro will be labelled using the default labeling system

which labels macros in ascending numerical order (e.g., M1,M2, M3, etc.).

9. MOSAIC will ask you where you want to copy the macro.

• To have it appear on all Device Screens,tap on the ALL DEVICES key. You will see a row of up to

four empty keys appear which correspond to the space directly below Device Selection Strip. Ta p

on any empty key to assign it or tap on an existing one to override it.MOSAIC will display a con-

firmation screen.

• To have it appear on a specific Device Screen,tap on the SPECIFIC DEVICE key.You will see the

last-displayed Device Screen.Using the Device Selection Strip, tap on the desired device key.If need-

ed, tap on left/right scroll arrows to view other device choices. The Device Screen will display all

keys on all pages for the selected device.Tap on any empty key.MOSAIC will display a confirma-

tion screen.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

10. Repeat steps 1 through 9 for each new macro you want to create.

1 2 3

4 5 6

7 8 9

0

-/--

AV PWR

DELAY TEST CLEAR

ADD MACROS

Press TEST to check

the macro, OK to save

or CLEAR to start over.

Esc

OK

CBLTV VCR

T

YES NO

ADD MACROS

Relabel the key?

14 www.oneforall.com

VIEWING MACROS

To see what commands are stored in a macro,perform the following steps:

1. On the Device Screen in the upper left corner,tap on Setup.You will see the main SETUP Menu

that greets you and asks,“What would you like to configure?”

2. Tap on the PERSONALIZATION key.You will see the PERSONALIZATION Menu.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

3. Tap on the MACROS key.You will see the main MACROS Menu.

4. Tap on the VIEW key.You will see the VIEW MACROS Menu.

5. Tap on any displayed Macro key (e.g.,M1, M2,etc.).You will see the commands that make up

the selected macro.To return to previous menu,tap on the

ESC key. To return to the Device

Screen,press down on

ESC or MUTE for at least 2 seconds.

ADD

VIEW

COPY

DELETE

DELETE ALL

MACROS

Program a sequence of

keystrokes onto one key.

Esc ?

Tap on

M 1 M 2 M 3

VIEW MACROS

Select a Macro key.

Esc

www.oneforall.com 15

COPYING MACROS

To copy a macro,perform the following steps:

1. On the Device Screen in the upper left corner,tap on Setup.You will see the main SETUP Menu

that greets you and asks,“What would you like to configure?”

2. Tap on the PERSONALIZATION key.You will see the PERSONALIZATION Menu.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

3. Tap on the MACROS key.You will see the main MACROS Menu.

4. Tap on the COPY key.You will see the COPY MACROS Menu.

5. Tap on the macro key you want to copy.MOSAIC will ask you where you want to copy the macro.

• To have it appear on all Device Screens,tap on the ALL DEVICES key. You will see a row of up

to four empty keys appear which correspond to the space directly below Device Selection Strip.

Tap on any empty key to assign it or tap on an existing one to override it.MOSAIC will display a

confirmation screen.

• To have it appear on a specific Device Screen,tap on the SPECIFIC DEVICE key.You will see the

last-displayed Device Screen.Using the Device Selection Strip, tap the desired device key.If needed,

tap the left/right scroll arrows to view other device choices.The Device Screen will display all keys

on all pages for the selected device.Tap on any empty key and MOSAIC will display a confirma-

tion screen.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

ADD

VIEW

COPY

DELETE

DELETE ALL

MACROS

Program a sequence of

keystrokes onto one key.

Esc ?

Tap on

M 1 M 2 M 3

COPY MACROS

Select a Macro key.

Esc

16 www.oneforall.com

DELETING A MACRO

To delete a single macro,perform the following steps:

1. On the Device Screen in the upper left corner,tap on Setup.You will see the main SETUP Menu

that greets you and asks,“What would you like to configure?”

2. Tap on the PERSONALIZATION key.You will see the PERSONALIZATION Menu.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

3. Tap on the MACROS key.You will see the main MACROS Menu.

4. Tap on the DELETE key.You will see the DELETE MACROS Menu.

5. Tap on the Macro key you want to delete.You will see a confirmation screen that says the macro

key has been successfully deleted from all device screens and the main MACROS Menu.

NOTE: Use VIEW/DELETE (see PERSONALIZATION – VIEW/DELETE on page 32) to delete

macros from Device Screens but keep them intact on the main MACROS Menu for future copy-

ing.

To delete another macro key, tap on the ESC key to return to the DELETE MACROS Menu, or press

down on

ESC or MUTE for at least 2 seconds to return to the last-displayed Device Screen.

ADD

VIEW

COPY

DELETE

DELETE ALL

MACROS

Program a sequence of

keystrokes onto one key.

Esc ?

Tap on

M 1 M 2 M 3

DELETE MACROS

Select a Macro key.

Esc

www.oneforall.com 17

DELETING ALL MACROS

To delete all macros,perform the following steps:

1. On the Device Screen in the upper left corner,tap on Setup.You will see the main SETUP Menu

that greets you and asks,“What would you like to configure?”

2. Tap on the PERSONALIZATION key.You will see the PERSONALIZATION Menu.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

3. Tap on the MACROS key.You will see the main MACROS Menu.

4. Tap on the DELETE ALL key.MOSAIC will ask you to confirm your choice.

• To delete all macros,tap on the YES key.You will see a confirmation screen that says all macros

have been successfully deleted on all device screens and the main MACROS Menu.Tap on the

ESC key to return to the DELETE MACROS Menu.

NOTE: Use VIEW/DELETE (see Personalization - View/Delete on page 32) to delete macros

from Device Screens but keep them intact on the main MACROS Menu for future copying.

• To cancel deletion of all macros,tap on the NO key.MOSAIC will return to the main MACROS

Screen.If you want to delete a single macro,see the previous section,Deleting A Macro on page

17,or see View/Delete on page 32.

NOTE: To return to a previous menu,tap on the ESC key.To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help, tap the ? key.

ADD

VIEW

COPY

DELETE

DELETE ALL

MACROS

Program a sequence of

keystrokes onto one key.

Esc ?

Tap on

YES NO

MACROS

Are you sure you want to

DELETE ALL?

18 www.oneforall.com

MOVE KEY

MOSAIC also includes our patented Key Mover feature that allows keys to be copied from one device to

another,or to a different position in the same device mode.However,there are some considerations:

• A moved key is actually a copy of the original key.The original key cannot be deleted.

• A moved key will always be rectangular,even though the original version may be a different

shape.

• A moved key retains the original label,but it can be relabelled.

• The Key Mover feature only works on IR function keys.

Example: we’ll create an example that copies the AV key from TV Device Screen

and adds it to the CBL Device Screen.

1. On the Device Screen in the upper left corner,tap on Setup.You will see the main SETUP Menu

that greets you and asks,“What would you like to configure?”

2. Tap on the PERSONALIZATION key.You will see the PERSONALIZATION Menu.

NOTE: To return to a previous menu,tap on the ESC key. To return to last-displayed Device

Screen, press down on ESC or MUTE for at least 2 seconds.For help,tap the ? key.

3. Tap on the MOVE KEY key.You will see the MOVE KEY Menu.

4. Tap on the MOVE key.You will see the Device Selection Strip and MOSAIC asks you to choose a

device from which to move a key.

5. Tap on a desired device key.For our example,tap on the TV key.MOSAIC will ask you to choose

a key to be moved.

6. Tap on the key you want moved.If needed,tap on the Page Arrow keys to view other pages for the

selected device.For our example,tap on the AV key.Again you will see the Device Selection Strip,

but this time MOSAIC asks you to choose a device where the key will be moved to.

7. Tap on a desired device key.For our example,tap on the CBL key.MOSAIC will ask you to

choose a key.

MOVE

DELETE ALL

MOVE KEY

Select the below functions

to rearrange keys within

or across devices.

Esc ?

Tap on

From which device?

MOVE KEY

Esc

CBLTV VCR

www.oneforall.com 19

Page is loading ...

One For All urc 9990 mosaic User manual

This manual is also suitable for

One For All urc 9990 mosaic User manual

Related papers

Other documents