Agri-Fab 45-03201 User manual

Type
User manual

This manual is also suitable for

PRINTED IN U.S.A. FORM NO. 40636 (REV. 3/11/08)
42" LAWNSWEEPER
BARREDORA DE CESPED DE 106 cm
BALAYEUSE DE PELOUSE 106 cm
OWNERS MANUAL
MANUAL DEL USUARIO
NOTICE D’UTILISATION
CAUTION:
Read Rules for
Safe Operation
and Instructions
Carefully
Model No.
Modelo No.
Modèle No.
45-03201
45-03201-062
ATTENTION:
Lire et suivre attentivement
les instructions et
consignes de sécurité de
cette notice.
PRECAUCION:
Lea cuidadosamente
los Procedimientos e
Instrucciones para la
Operación Segura de la
Máquina.
• Safety
• Assembly
• Operation
• Maintenance
• Parts
• Seguridad
• Montaje
• Operación
• Mantenimiento
• PiezasdeRepuesto
• Sécurité
• Assemblage
• Fonctionnement
• Maintenance
• PiècesdeRechange
Aerosmith Rocks
the fastest way to purchase parts
www.speedepart.com
2
1. SweeperHousingAssembly
2. BagArmTube(2)
3. HitchTube,L.H.
4. HitchBracket
5. HitchBracket(Straight)
6. HeightAdjustmentStrap
7. HeightAdjustmentHandle
8. HitchTube,R.H.
9. BrushAssembly(2)
10. UpperHopperSideTube(2)
11. RearHopperTube(2)
12. LowerHopperSideTube(2)
13. Hopper Support Rod (2)
14. Bag Frame Strap
15. Hopper Bag
16. Rope
1
2
3
4
5
6
7
8
2
16
15
10
10
12
13
11
11
12
14
9
1. ConjuntodeCarcazadelaBarredora
2. BrazodelTubodelaBolsa(2)
3. TubodeEnganche(ManoIzquierda)
4. MénsuladeEnganche
5. MénsuladeEnganche(Recta)
6. BarradeAjustedeAltura
7. ManijadeAjustedeAltura
8. TubodeEnganche(ManoDerecha)
9. ConjuntodeCepillo(2)
10. TuboLateraldelaParteSuperiorde
la Tolva (2)
11. TubodelaPartePosteriordelaTolva(2)
12. TuboLateraldelaParteInferiorde
la Tolva (2)
13. Barra de Soporte de la Tolva (2)
14. Varilla del Marco de la Bolsa
15. Bolsa de la Tolva
16. Cuerda
1. Bâtidelabalayeuse
2. Tubedubrasdusac(2)
3. Tubed‘attelage,côtédroit
4. Support de l’attelage
5. Supportdel’attelage,droit
6. Étrierderéglagedelahauteur
7. Manchederéglagedelahauteur
8. Tubed’attelage,côtédroit.
9 Brosses (2)
10. Tubelatéralsupérieurdela
trémie (2)
11. Tubearrièredelatrémie(2)
12. Tubelatéralinférieurdela
trémie (2)
13. Tiges de support de la trémie (2)
14. Bride du cadre du sac
15. Sacderécupérationdesdébris
16. Cordage
FRANÇAIS
ESPAÑOL
ENGLISH
CARTON CONTENTS (Loose Parts in Carton)
CONTENIDO DE LA CAJA(PartesSueltasenlaCaja)
CONTENU DU CARTON(PiècesenVracDansleCarton)
3
REF QTY DESCRIPTION
A 2 HexBolt,5/16x2-1/2"Lg.
B 2 HexBolt,5/16x2"Lg.
C 4 CarriageBolt,5/16"x1-1/2"
D 1 HexBolt,5/16x1-1/4"Lg.
E 2 HexBolt,5/16"x1"
F 1 CarriageBolt,5/16"x1"
G 4 HexBolt,1/4"x1"
I 4 NylockNut,1/4"
J 11 NylockNut,5/16"
K 4 FlatWasher,5/16"
L 1 StarWasher
M 1 HairCotterPin,1/8"
N 8 HairCotterPin,3/32"
A B C
D
F G
I
J
M
N
K
Y
Z
L
Q
TS U
SHOWN FULL SIZE
NOT SHOWN FULL SIZE
P
O
E
R
V W X
ENGLISH
REF QTY DESCRIPTION
O 2 ClevisPin,3/8"x1/2"
P 2 ClevisPin,1/4"x1-1/8"
Q 2 ClevisPin,1/4"x1-3/4"
R 2 ClevisPin,3/8"x3"
S 1 PivotBushing
T 1 SpacerBushing
U 2 HitchSpacer,3/4"
V 2 Vinyl Cap
W 1 Grip
X 1 Knob,Plastic
Y 1 HitchPin
Z 4 Plastic Plug
4
6. Vehicle braking and stability may be affected with
theattachmentofthissweeper.Donotllsweeperto
maximumcapacitywithoutcheckingthecapabilityofthe
towingvehicletosafelypullandstopwiththesweeper
attached.Stay off of steep slopes.
7. Stopandinspectvehicleandsweeperfordamageafter
strikinganobject.Repairanydamagebeforecontinuing
operation.
8. Keep sweeper away from re. Excessive heat can
damagethebrushesandhopperbagandcouldcause
thebaganditscontentstoburn.
9. Beforestoringthesweeper,alwaysemptythehopper
bagtoavoidspontaneouscombustion.
10. Follow maintenance and lubrication instructions as
outlinedinthemaintenancesectionofthismanual.
1. Readthevehicle and sweeper ownersmanualsand
knowhowtooperateyourvehicleandsweeperbefore
usingthissweeperattachment.Alwaysinstructother
usersbeforetheyoperatethesweeper.
2. Donotpermitchildrentooperatesweeper.
3. Do not permit anyone to ride on sweeper.
4. Neverattachthehopperropetoanypartofyourbody
orclothing!Neverholdontotheropewhiletowingthe
sweeper!Attachtheropetothetowingvehicletokeep
itawayfromwheelsandrotatingparts.
5. Operate the sweeper at reduced speed on rough
terrain,nearditchesandonhillsidestopreventlossof
control.
Remember,anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperate
theequipment.Exercisecautionatalltimeswhenusingpowerequipment.
Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans–Attention!!
Become alert!! Your safety is involved.
SAFETY RULES
ENGLISH
5
TOOLS REQUIRED FOR ASSEMBLY
(2) 7/16"OpenEndorBoxEndWrenches
(2) 1/2"OpenEndorBoxEndWrenches
ASSEMBLY
Allloosepartsareshownonpage2.Fastenersintheparts
bagareshownfullsizeonpage3.
Removethehardwarepackandallloosepartsfromthe
cartonandverifythatallthepartsandfastenersshownon
pages 2 and 3 are included.
ASSEMBLY OF SWEEPER
Note: Righthand(R.H.)andlefthand(L.H.)aredetermined
fromtheoperator'spositionwhileseatedonthetractor.
ENGLISH
1. (Figure 1)Eachbrushassemblyhasonebrushretainer
markedwitheitherredorblackink.Layoutthebrush
assembliesasshownsothatthebrushretainersmarked
withinkareinthemiddlewiththeredoneontheright
andtheblackoneontheleft.
OVERLAP BRISTLES
BRUSH RETAINER
MARKED BLACK
BRUSH RETAINER
MARKED RED
1
IMPORTANT:Theoverlapbristlesatthebottomofeachbrush
helpsupportthebacksideofthebrushforbettersweeper
performance.Besurethesweeperisturnedasshownin
gures2and3tocorrectlyassemblethebrushes.
2. (Figure 2) Attach the brush assembly with the red
brushretainertotherightendofthebrushshaftusing
two1/4"x1"hexbolts(G)and1/4"nylocknuts(I).The
brushretainermarkedwithredinkmustbeplacedto
themiddleofthesweeper.
BRUSH RETAINER
MARKED RED
OVERLAP
BRISTLES
1/4" x 1"
HEX BOLT (G)
1/4" NYLOCK NUT (I)
BRUSH RETAINER
MARKED RED
2
6
5/16" x 1-1/2"
CARRIAGE BOLT (C)
5/16" NYLOCK NUT (J)
5. Cutofftheplastictiethatholdstheheightadjustment
tubeinplace.
6. (Figure 4)AssembletheR.H.hitchtubetothesweeper
housingusingtwo5/16"x1-1/2"carriagebolts(C),and
two5/16"nylocknuts(J).Do not tighten yet. Repeat
fortheL.H.hitchtube.
7. (Figure 5)Fastenthehitchtubestogetherusingtwo
5/16"x2-1/2"hexbolts(A)and5/16"nylocknuts(J).
Do not tighten yet.
5
5/16" x 2-1/2"
HEX BOLT (A)
5/16"
NYLOCK NUT (J)
3. (Figure 3)Attachthebrushassemblywiththeblack
brushretainertotheleftendofthebrushshaftusing
two1/4"x1"hexbolts(G)and1/4"nylocknuts(I).The
brushretainermarkedwithblackinkmustbeplacedto
themiddleofthesweeper.
4. (Figure 3)Turna wheel to rotatethe brushes. (The
wheelsdrivethe brushesin one direction only.)The
overlapbristlesshouldbeonthebacksideofthebrush
as it rotates.
3
ENGLISH
4
7
11. (Figure 8) Assemble the height adjustment handle
totheinsideofthebracketontheendoftheheight
adjustmenttube.Usetwo5/16"x1"hexbolts(E),5/16"
atwashers(K)and5/16"nylocknuts(J).Tighten.
12. (Figure 8) Assemble the grip (W) onto the height
adjustmenthandle.
13. (Figure 9)Assembleontoa5/16"x1-1/4"hexbolt
(D)intheorderlisted,a5/16"atwasher(K),thepivot
bushing(S),theheightadjustmentstrapandthespacer
bushing(T).Inserttheboltthroughtheupperpartof
thedoubleholeintheendofthesweeperhousingand
secureitwitha5/16"nylocknut(J).Tighten.
If your tractor hitch has 10" to 13" ground clearance refer
to gure 6. If your tractor hitch has 8" to 10" ground
clearance refer to gure 7.
8. (Figure 6 or 7)Assemblethehitchbracketstothehitch
tubesusingtwo5/16"x2"hexbolts(B)and5/16"nylock
nuts(J).Theboltsshouldstraddlethefronthitchtube
bolt.Do not tighten yet.
9. Atthistimetightenthefourboltsfasteningthehitch
tubestothesweeperhousing.Next,tightenthetwobolts
fasteningtheendsofthehitchtubestogether.Finally,
tightenthetwoboltsfasteningthehitchbracketstothe
hitchtubes.
10. (Figure 6 or 7)Assemblethehitchpin(Y),two3/4"hitch
spacers(U)andthe1/8"haircotterpin(M)tothehitch
brackets.
6
5/16" x 2"
HEX BOLT (B)
5/16" NYLOCK
NUT (J)
3/4" SPACER (U)
HITCH BRACKET
HITCH BRACKET
(STRAIGHT)
1/8" HAIR
COTTER PIN (M)
HITCH PIN (Y)
5/16" NYLOCK NUT (J)
HEIGHT
ADJUSTMENT
HANDLE
GRIP (W)
5/16" FLAT WASHER (K)
5/16" x 1" HEX BOLT (E)
8
9
7
5/16" x 2"
HEX BOLT (B)
5/16" NYLOCK
NUT (J)
3/4" SPACER (U)
HITCH PIN (Y)
HITCH BRACKET
(STRAIGHT)
1/8" HAIR
COTTER PIN (M)
HITCH BRACKET
ENGLISH
PIVOT BUSHING (S)
5/16" NYLOCK NUT (J)
SPACER BUSHING (T)
5/16" FLAT WASHER (K)
5/16" x 1-1/4"
HEX BOLT (D)
HEIGHT ADJUSTMENT
STRAP
8
14. (Figure 10) Place the star washer (L) between the
heightadjustmenthandleandtheheightadjustmenet
strap. Insertthe 5/16"x 1" carriage bolt (F) through
theheightadjustmenthandle,thestarwasherandthe
heightadjustmentstrap.Assemblea5/16"atwasher
(K)andtheplasticknob(X)ontotheendofthebolt.
ASSEMBLY OF HOPPER BAG
1. (Figure 11)Turnarearhoppertubesothatthebrace
holesinthemiddleofthetubeface down.Slidethe
tubethroughthetwoloopssewntothetoprearseam
insidethehopperbag.
2. (Figure 12) Insert the two upper hopper side tubes
throughthestitchedapsoneachsideofthehopper
bag.
3. (Figure 12)Assembletheendsoftherearhoppertube
ontotheendsoftheupperhoppersidetubes.Fasten
togetherusingplasticplugs(Z).
UPPER HOPPER
SIDE TUBE
PLASTIC PLUG (Z)
REAR HOPPER TUBE
(brace holes on bottom)
INNER BAG LOOPS
10
11
12
ENGLISH
5/16" FLAT
WASHER (K)
5/16" x 1"
CARRIAGE BOLT (F)
PLASTIC KNOB (X)
STAR WASHER (L)
(between strap and handle)
9
7. (Figure 15)Insertthebagframestrapintothestitched
sleevealongthefrontedgeofthebagbottom.
8. (Figure 15)Assemblethebagframestraptothelower
hoppersidetubesusingtwo1/4"x1-1/8"clevispins
(P)and3/32"haircotterpins(N).
SNAP
FLAP
9. (Figure 16)Securethebagcornersaroundthelower
hoppersidetubesbysnappingthebagapstothebag
bottomonbothsides.
4. (Figure 13)Turnthesecondrearhoppertubesothatthe
braceholesinthemiddleofthetubeface up.Assemble
theendsoftherearhoppertubeontotheendsofthe
lowerhoppersidetubes.Fastentogetherusingplastic
plugs (Z).
5. (Figure 14)Placetheassembledlowerhoppertubes
intothebottomofthehopperbag
6. (Figure 14)Attachtheendsofthelowerhopperside
tubestotheinsideoftheupperhoppersidetubesusing
two3/8"x1/2"clevispins(O)insertedfromtheinside,
andtwo3/32"haircotterpins(N).
LOWER
HOPPER
SIDE TUBE
PLASTIC PLUG (Z)
REAR HOPPER TUBE
(brace holes on top)
13
14
LOWER HOPPER
SIDE TUBE
HOPPER BAG
BOTTOM
UPPER HOPPER
SIDE TUBE
3/8" x 1/2"
CLEVIS PIN (O)
3/32" HAIR
COTTER PIN (N)
15
1/4" x 1-1/8"
CLEVIS PIN (P)
3/32" HAIR
COTTER PIN (N)
BAG FRAME STRAP
16
ENGLISH
10
IMPORTANT: Do notoverbendthesupportrodsduring
thefollowingstep.Overbendingwillcausethesteelrods
to loose supporting tension.
10. (Figure 17)Tipthehopperontoit'sbacktoassemble
thetwohoppersupportrods.Placetheendsofeach
rodintotheupperandlowerrearhoppertubes,bending
therodjustenoughtotintotheholesinthetubes.
11. (Figure 18)Inserta3/8"x3"clevispin(R)through
thelowerholeineachupperhoppersidetube.Next
assemble a bag arm tube onto each clevis pin and
secureitwitha3/32"haircotterpin(N).
12. (Figure 18)Assembleavinylcap(V)ontotheendof
eachbagarmtube.

SUPPORT
RODS
13. (Figure 19)Securetheropetothetopcenterofthe
hopperbagframe.
14. (Figure 20)Toassemblethehopperbagtothesweeper,
slidetheendsofthebagarmtubesintotheendsofthe
sweeper'shitchtubesandsecurewithtwo1/4"x1-3/4"
clevispins(Q)and3/32"haircotterpins(N).
17
18
19
20
LOWER HOLE
3/32" HAIR
COTTER PIN (N)
3/8" x 3"
CLEVIS PIN (R)
BAG ARM TUBE
VINYL CAP (V)
BAG ARM TUBE
1/4" x 1-3/4"
CLEVIS PIN (Q)
3/32" HAIR
COTTER PIN (N)
ENGLISH
11
ATTACHING SWEEPER HITCH TO TRACTOR
(Figures 21, 22, 23)
1. Placethetractorandsweeperonaatlevelsurface.
2. Setthesweeperheightadjustmenthandletoaboutthe
middleofitsadjustmentrange.
3. Attachthesweeperhitchbracketstothetractorhitch,
arrangingthe3/4"spacerssothatthebottomofthe
sweeperbagisapproximatelyleveland5"to7"above
theground.Seegure22fortractorhitchesthatare
10"to13"abovetheground.Seegure23fortractor
hitchesthatare8"to10"abovetheground.
IMPORTANT: Forbestperformance,thebottomofthe
sweeperbagshouldbeapproximatelyleveland5"to7"off
thegroundasshowningure21.
Tractor hitches with 8" to 10" ground clearance.
21
2322
Tractor hitches with 10" to 13" ground clearance.
TRACTOR HITCH
8"-10"
TRACTOR HITCH
10"-13"
ENGLISH
5" Min.
Aerosmith Rocks
12
HEX BOLT FLAT WASHER
FLAT WASHER
HEX LOCK NUT
HUB CAP
SPACER
HEIGHT ADJUSTMENT SLOT
HEX BOLT
OIL BEARINGS HERE
FLAT WASHER
HOW TO USE YOUR SWEEPER
BRUSH HEIGHT ADJUSTMENT
Toadjustyoursweeperbrushestothebestoperating
height, loosen the adjustment knob and push down
ontheheightadjustmentlevertoraisethebrush.Best
adjustmentiswhenthebrushsettingis1/2"downinto
the grass. Always mow the grassto an even height
beforesweeping.
SWEEPING SPEED
Trya startingspeedofapproximately3m.p.h.(third
gearonmosttractors).Dependingontheconditions,
itmaybenecessarytoadjustthesweepingspeedin
ordertoachievebestresults.
DUMPING OF SWEEPER
Your sweepercan be dumpedeasily without getting
offoftheriderortractor.Simplypulltheropeforward
todumpthehopper.Alwaysemptyhopperaftereach
use.
CAUTION: Keep sweeper awayfrom re.
Excessiveheatcandamagethebrushesand
hopperbagandcouldcausethebagandits
contentstoburn.
CAUTION: Never attachthehopperrope
toanypartofyourbodyorclothing!Never
hold ontotheropewhiletowingthesweeper!
Attach the ropetothetowingvehicletokeep
itawayfromwheelsandrotatingparts.
OPERATION
CUSTOMER RESPONSIBILITIES
1. Checkforloosefastenersbeforeeachuse.
2. Cleanthesweeperaftereachuse.
a. Cleansweeperhousingwithasoftbrushorcloth.
b. Cleandebrisfromhopperbagwithabrushor
broom.
c. Removeanymaterialwhichhaswrappedaround
brushesorendsofbrushshaft.
3. Inspectforwornordamagedparts,suchasbrushes
andwheelsbeforeeachuse.Replaceasnecessary.
MAINTENANCE
5. Lubricate the wheelbearingseachseason.Remove
thehubcapandapplyafewdropsoflightweightoil.
6. (Figure 25)Everytwoyears,removethewheelsand
cleanthegearsfoundinsidethewheelhousing.After
cleaning,lubricatethegearswithanevencoatoflight
grease.Toremovethewheel,popoffthehubcapand
removethelocknutandatwasher.
24
25
1. Cleanthesweeperandhopperbagthoroughlytohelp
prevent rust and mildew.
2. Tocollapsethehopperbagforstorage,removethetwo
hoppersupportrodsfromtherearofthehopper.
3. Store in a dry area.
CAUTION: Before storing the sweeper,
always empty the hopper bag to avoid
spontaneouscombustion.
STORAGE
4. (Figure 24)Lubricatethebrushshaftbearingtwicea
yearwithafewdropsoflightweightoil.
ENGLISH
13
WHEEL GEAR AND PAWL SERVICE
IMPORTANT: Do notremovebothwheelsatthesame
timetoavoidmixingofparts.(TheR.H.andL.H.ratchet
gearsarenotinterchangeable.)Make notesontheposition
ofwashersandsnapringsduringdisassembly.
1. Remove only onewheelfromthesweeper.
2. Removetheretainingringsandwasherswhichholdthe
ratchetgearontothebrushshaft.
3. (Figure 27)Removethegearbyslidingitoffthebrush
shaft.(Lookforthedrivepin,whichmayfalloutofthe
brushshaftwhentheratchetgearisremoved.)
4. Toreassemble,insertthedrivepin through thehole
neartheendofthebrushshaft.Makesurethepinslides
backandfortheasilyintheshaft.
5. Lightlygreasetheshaftandlltheratchetgearwith
grease. Assemble the ratchet gear back onto the
shaft.
6. Lightlygreasetheaxleandthegearteethonthewheel,
andthenreassemblethewheel.Thebrushesshould
rotate onlyduringforwardrotationofthewheel.Ifthe
brushesaredriven(rotated)bybothforwardandreverse
rotationofthewheel,thedrivepinisjamminginthe
ratchetgear.Disassembletocleanandlubricatethe
drivepinandtheratchetgear.
7. Removethesecondwheelandrepeattheprocedure.
BRUSH REPLACEMENT
NOTE: Brushreplacementshouldbedoneonebrushat
a time.
1. Removethehopperbagfromthesweeper.
2. (Figure 26)Loosenthehexboltsandlocknutsontwo
singlebrushretainerswhichclamponebrushtothe
doublebrushretainers.Do Not loosenorremovethe
bolts which fastenthe doublebrush retainers to the
brushshaft.
3. (Figure 26)Slidethebrushoutoftheretainers,noting
onwhichsideofthebrushthebristlesoverlap.
4. (Figure 26)Installnewbrush,makingsurethebristles
overlaponthesamesideofthebrushasbefore.
1.Brushessettoolow.
2. Brushesarejammed
3. Wheelsarejammed.
Wheelsskidwhensweeping. 1. Adjustheighttillbrushesare1/2"downintograss.
2. Stopsweeper.Removeobstruction.
3. Removeonewheelatatimetocheckforobstructionor
damage.RefertoServiceandAdjustmentssection.
SERVICE AND ADJUSTMENTS
TROUBLESHOOTING
26
27
ENGLISH
BRUSH ROTATION
BRUSH ROTATION
OVERLAP
BRISTLES
OVERLAP
BRISTLES
SINGLE
BRUSH
RETAINERS
DOUBLE BRUSH RETAINER
BRUSH
SHAFT
RATCHET
GEAR
DRIVE
PIN
27
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS FOR MODEL 45-03201, 45-03201-062 42" LAWNSWEEPER
REF PART NO. QTY DESCRIPTION
1 40614 1 HitchTube,R.H.
2 40615 1 HitchTube,L.H.
3 23353 1 Pin,Hitch
4 23368 2 Tube,HitchSpacer
5 43343 1 HairpinCotter,1/8"#4
7 C-9M5732 8 Rivet,Pop
9 43182 4 Bolt,Hex5/16-18x3/4"
10 66137 1 SweeperHousingAssembly
11 23336 2 Washer,Special
12 66070 1 HeightAdjustmentTubeAssembly
13 43063 2 Bolt,Hex5/16-18x1"
14 25408 1 Bushing,Spacer
15 43840 1 Bolt,Hex5/16-18x1-1/4"
16 44732 1 Washer,Star
17 R19212113 2 Washer,5/8"SAE
18 1629-56 2 Retainer,DustCover
19 44910 2 Bushing,BrushShaft
20 25850 1 BrushShaft
21 48557 4 Brush
22 43012 8 Bolt,Hex1/4-20x3/4"Lg.
23 47189 12 Nut,Nylock1/4-20
24 23580 4 Retainer,Brush(Double)
25 23581 8 Retainer,Brush(Single)
26 44008 2 Washer,Flat1-1/8"x.78"x.025"
27 47046 2 Dowel Pin (Drive)
29 47810 15 Nut,Nylock5/16-18
30 44911 2 Spacer,.39I.D".x1-1/4"O.D.x.5"
31 44006 2 Washer,Flat.849"x.598"x.025"
32 46219 2 Spacer,.78I.D".x1-1/4"O.D.x.5"
33 1650-21 2 Ring,Retaining.594"
34 40001 6 Washer,Shim1-1/8"x.594"x.025"
35 141 4 Washer,Flat1-1/2"x.375"x.062"
36 1038 2 Nut,NylockJam3/8-24Thread
37 2674-32 2 HubCap
38 44961 2 Bolt,Hex3/8-24x3-1/4"Lg.
REF PART NO. QTY DESCRIPTION
39 23400 3 Bushing,Pivot
40 48652 1 Gear,PinionR.H.(notshown)
41 48651 1 Gear,PinionL.H.
42 43661 4 Bolt,Hex1/4-20x1"Lg.
43 64559 2 Ass'y,DustCover
44 48587 2 Tube,HopperFrame(Rear)
45 48466 2 Tube,UpperHopperFrame(Front)
46 48726 2 Tube,LowerHopperFrame(Front)
47 48402 4 Plastic Plug
48 48388 1 Hopper Bag
49 48366 2 ClevisPin,3/8"x1/2"
50 24949 1 Strap,BagFrame
51 43926 2 Rod,HopperSupport
52 43737 1 Hopper Rope
53 44481 2 Cap,Vinyl
54 24979 1 Strap,HeightAdjustment
55 23687 1 Bracket,Hitch
56 24192 1 Bracket,Hitch(Straight)
57 26243 1 Handle,HeightAdjustment
58 40621 2 Tube,BagArm
59 43513 2 Pin,Clevis3/8"x3"
60 44985 2 Wheel&TireAss'y.(withbearings)
61 45088 4 WheelBearing
62 44292 2 Bolt,Hex5/16-18x2-1/2"Lg.
63 44180 2 Bolt,Hex5/16-18x2"Lg.
65 43681 4 Bolt,Carriage5/16-18x1-1/2"
66 43055 8 HairpinCotter,3/32"#3
67 43720 1 Knob,Wing5/16-18Thread
68 44326 1 Bolt,Carriage5/16-18x1"
69 43081 4 Washer,Flat5/16"Std.Wrt.
70 43943 1 Grip,HeightAdjust
71 46867 2 ClevisPin,1/4"x1-3/4"Lg.
72 48365 2 ClevisPin,1/4"x1-1/8"
40636 1 Owners Manual
the fastest way to purchase parts
www.speedepart.com
REPAIR PARTS
Agri-Fab,Inc.
809SouthHamilton
Sullivan,IL.61951
217-728-8388
www.agri-fab.com
©2003Agri-Fab,Inc.
Thisdocument(ormanual)isprotectedundertheU.S.CopyrightLawsandthecopyrightlawsofforeigncountries,
pursuanttotheUniversalCopyrightConventionandtheBerneconvention.Nopartofthisdocumentmaybereproduced
ortransmittedinanyformorbyanmeans,electronicormechanical,includingphotocopyingorrecording,orbyany
informationstorageorretrievalsystem,withouttheexpresswrittenpermissionofAgri-Fab,Inc.Unauthorizedusesand/or
reproductionsofthismanualwillsubjectsuchunauthorizedusertocivilandcriminalpenaltiesasprovidedbytheUnited
StatesCopyrightLaws.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Agri-Fab 45-03201 User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI