Agri-Fab 45-03311 User manual

PRINTED IN U.S.A. FORM NO. 40634 (REV. 03/17/08)

38" LAWNSWEEPER

BARREDORA DE CESPED DE 96 cm

BALAYEUSE DE 96 cm

OWNERS MANUAL

MANUAL DEL USUARIO

NOTICE D’UTILISATION

CAUTION:

Read Rules for

Safe Operation

and Instructions

Carefully

Model No.

Modelo No.

Modèle No.

45-03311

ATTENTION:

Lire et suivre attentivement

les instructions et

consignes de sécurité de

cette notice.

PRECAUCION:

Lea cuidadosamente

los Procedimientos e

Instrucciones para la

Operación Segura de la

Máquina.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Seguridad

• Montaje

• Operación

• Mantenimiento

• PiezasdeRepuesto

• Sécurité

• Assemblage

• Fonctionnement

• Maintenance

• PiècesdeRechange

™

the fastest way to purchase parts

www.speedepart.com

Aerosmith Rocks

CARTON CONTENTS (Loose Parts in Carton)

CONTENIDO DE LA CAJA(PartesSueltasenlaCaja)

CONTENU DU CARTON(PiècesenVracDansleCarton)

1. SweeperHousingAssembly

2. BagArmTube(2)

3. HitchTube,L.H.

4. HitchBracket

5. HitchBracket(Straight)

6. HeightAdjustmentStrap

7. HeightAdjustmentHandle

8. HitchTube,R.H.

9. BrushAssembly(2)

10. UpperHopperSideTube(2)

11. RearHopperTube(2)

12. LowerHopperSideTube(2)

13. Hopper Support Rod (2)

14. Bag Frame Strap

15. Hopper Bag

16. Rope

1. ConjuntodeCarcazadelaBarredora

2. BrazodelTubodelaBolsa(2)

3. TubodeEnganche(ManoIzquierda)

4. MénsuladeEnganche

5. MénsuladeEnganche(Recta)

6. BarradeAjustedeAltura

7. ManijadeAjustedeAltura

8. TubodeEnganche(ManoDerecha)

9. ConjuntodeCepillo(2)

10. TuboLateraldelaParteSuperiorde

la Tolva (2)

11. TubodelaPartePosteriordelaTolva(2)

12. TuboLateraldelaParteInferiorde

la Tolva (2)

13. Barra de Soporte de la Tolva (2)

14. Varilla del Marco de la Bolsa

15. Bolsa de la Tolva

16. Cuerda

1. Bâtidelabalayeuse

2. Tubedubrasdusac(2)

3. Tubed‘attelage,côtédroit

4. Support de l’attelage

5. Supportdel’attelage,droit

6. Étrierderéglagedelahauteur

7. Manchederéglagedelahauteur

8. Tubed’attelage,côtédroit.

9. Brosses (2)

10. Tubelatéralsupérieurdela

trémie (2)

11. Tubearrièredelatrémie(2)

12. Tubelatéralinférieurdela

trémie (2)

13. Tiges de support de la trémie (2)

14. Bride du cadre du sac

15. Sacderécupérationdesdébris

16. Cordage

FRANÇAIS

ESPAÑOL

ENGLISH

A B C

F G

TS U

SHOWN FULL SIZE

NOT SHOWN FULL SIZE

V W X

REF QTY DESCRIPTION

A 2 HexBolt,5/16x2-1/2"Lg.

B 2 HexBolt,5/16x2"Lg.

C 4 CarriageBolt,5/16"x1-1/2"

D 1 HexBolt,5/16x1-1/4"Lg.

E 2 HexBolt,5/16"x1"

F 1 CarriageBolt,5/16"x1"

G 4 HexBolt,1/4"x1"

I 4 NylockNut,1/4"

J 11 NylockNut,5/16"

K 4 FlatWasher,5/16"

L 1 StarWasher

M 1 HairCotterPin,1/8"

REF QTY DESCRIPTION

N 8 HairCotterPin,3/32"

O 2 ClevisPin,3/8"x1/2"

P 2 ClevisPin,1/4"x1-1/8"

Q 2 ClevisPin,1/4"x1-3/4"

R 2 ClevisPin,3/8"x3"

S 1 PivotBushing

T 1 SpacerBushing

U 2 HitchSpacer,3/4"

V 2 Vinyl Cap

W 1 Grip

X 1 Knob,Plastic

Y 1 HitchPin

Z 4 Plastic Plug

6. Vehicle braking and stability may be affected with

theattachmentofthissweeper.Donotllsweeperto

maximumcapacitywithoutcheckingthecapabilityofthe

towingvehicletosafelypullandstopwiththesweeper

attached.Stay off of steep slopes.

7. Stopandinspectvehicleandsweeperfordamageafter

strikinganobject.Repairanydamagebeforecontinuing

operation.

8. Keep sweeper away from re. Excessive heat can

damagethebrushesandhopperbagandcouldcause

thebaganditscontentstoburn.

9. Beforestoringthesweeper,alwaysemptythehopper

bagtoavoidspontaneouscombustion.

10. Follow maintenance and lubrication instructions as

outlinedinthemaintenancesectionofthismanual.

1. Readthevehicleandsweeperownersmanualsand

knowhowtooperateyourvehicleandsweeperbefore

usingthissweeperattachment.Alwaysinstructother

usersbeforetheyoperatethesweeper.

2. Donotpermitchildrentooperatesweeper.

3. Do not permit anyone to ride on sweeper.

4. Neverattachthehopperropetoanypartofyourbody

orclothing!Neverholdontotheropewhiletowingthe

sweeper!Attachtheropetothetowingvehicletokeep

itawayfromwheelsandrotatingparts.

5. Operate the sweeper at reduced speed on rough

terrain,nearditchesandonhillsidestopreventlossof

control.

Remember,anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperate

theequipment.Exercisecautionatalltimeswhenusingpowerequipment.

Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!!

Become alert!! Your safety is involved.

SAFETY RULES

ENGLISH

TOOLS REQUIRED FOR ASSEMBLY

(2)  7/16"OpenEndorBoxEndWrenches

(2)  1/2"OpenEndorBoxEndWrenches

ASSEMBLY

Allloosepartsareshownonpage2.Fastenersintheparts

bagareshownfullsizeonpage3.

Removethehardwarepackandallloosepartsfromthe

cartonandverifythatallthepartsandfastenersshownon

pages 2 and 3 are included.

ASSEMBLY OF SWEEPER

Note: Righthand(R.H.)andlefthand(L.H.)aredetermined

fromtheoperator'spositionwhileseatedonthetractor.

1. (Figure 1)Eachbrushassemblyhasonebrushretainer

markedwitheitherredorblackink.Layoutthebrush

assembliesasshownsothatthebrushretainersmarked

withinkareinthemiddlewiththeredoneontheright

andtheblackoneontheleft.

OVERLAP BRISTLES

BRUSH RETAINER

MARKED BLACK

BRUSH RETAINER

MARKED RED

IMPORTANT:Theoverlapbristlesatthebottomofeachbrush

helpsupportthebacksideofthebrushforbettersweeper

performance.Besurethesweeperisturnedasshownin

gures2and3tocorrectlyassemblethebrushes.

2. (Figure 2) Attach the brush assembly with the red

brushretainertotherightendofthebrushshaftusing

two1/4"x1"hexbolts(G)and1/4"nylocknuts(I).The

brushretainermarkedwithredinkmustbeplacedto

themiddleofthesweeper.

BRUSH RETAINER

MARKED RED

OVERLAP

BRISTLES

1/4" x 1"

HEX BOLT (G)

1/4" NYLOCK NUT (I)

BRUSH RETAINER

MARKED RED

5/16" x 1-1/2"

CARRIAGE BOLT (C)

5/16" NYLOCK NUT (J)

5. Cutofftheplastictiethatholdstheheightadjustment

tubeinplace.

6. (Figure 4)AssembletheR.H.hitchtubetothesweeper

housingusingtwo5/16"x1-1/2"carriagebolts(C),and

two5/16"nylocknuts(J).Do not tighten yet. Repeat

fortheL.H.hitchtube.

7 (Figure 5)Fastenthehitchtubestogetherusingtwo

5/16"x2-1/2"hexbolts(A)and5/16"nylocknuts(J).

Do not tighten yet.

5/16" x 2-1/2"

HEX BOLT (A)

5/16"

NYLOCK NUT (J)

3. (Figure 3)Attachthebrushassemblywiththeblack

brushretainertotheleftendofthebrushshaftusing

two1/4"x1"hexbolts(G)and1/4"nylocknuts(I).The

brushretainermarkedwithblackinkmustbeplacedto

themiddleofthesweeper.

4. (Figure 3)Turn a wheelto rotatethe brushes. (The

wheelsdrivethebrushes in onedirectiononly.)The

overlapbristlesshouldbeonthebacksideofthebrush

as it rotates.

1/4" x 1"

HEX BOLT (G)

1/4" NYLOCK NUT (I)

BRUSH RETAINER

MARKED BLACK

ENGLISH

11. (Figure 8) Assemble the height adjustment handle

totheinsideofthebracketontheendoftheheight

adjustmenttube.Usetwo5/16"x1"hexbolts(E),5/16"

atwashers(K)and5/16"nylocknuts(J).Tighten.

12. (Figure 8) Assemble the grip (W) onto the height

adjustmenthandle.

13. (Figure 9)Assembleontoa5/16" x1-1/4"hexbolt

(D)intheorderlisted,a5/16"atwasher(K),thepivot

bushing(S),theheightadjustmentstrapandthespacer

bushing(T).Inserttheboltthroughtheupperpartof

thedoubleholeintheendofthesweeperhousingand

secureitwitha5/16"nylocknut(J).Tighten.

If your tractor hitch has 10" to 13" ground clearance refer

to gure 6. If your tractor hitch has 8" to 10" ground

clearance refer to gure 7.

8. (Figure 6 or 7)Assemblethehitchbracketstothehitch

tubesusingtwo5/16"x2"hexbolts(B)and5/16"nylock

nuts(J).Theboltsshouldstraddlethefronthitchtube

bolt.Do not tighten yet.

9. Atthistimetightenthefourboltsfasteningthehitch

tubestothesweeperhousing.Next,tightenthetwobolts

fasteningtheendsofthehitchtubestogether.Finally,

tightenthetwoboltsfasteningthehitchbracketstothe

hitchtubes.

10. (Figure 6 or 7)Assemblethehitchpin(Y),two3/4"hitch

spacers(U)andthe1/8"haircotterpin(M)tothehitch

brackets.

5/16" x 2"

HEX BOLT (B)

5/16" NYLOCK

NUT (J)

3/4" SPACER (U)

HITCH BRACKET

(STRAIGHT)

1/8" HAIR

COTTER PIN (M)

HITCH PIN (Y)

5/16" NYLOCK NUT (J)

HEIGHT

ADJUSTMENT

HANDLE

GRIP (W)

5/16" FLAT WASHER (K)

5/16" x 1" HEX BOLT (E)

5/16" x 2"

HEX BOLT (B)

5/16" NYLOCK

NUT (J)

3/4" SPACER (U)

HITCH PIN (Y)

HITCH BRACKET

(STRAIGHT)

1/8" HAIR

COTTER PIN (M)

HITCH BRACKET

ENGLISH

PIVOT BUSHING (S)

5/16" NYLOCK NUT (J)

SPACER BUSHING (T)

5/16" FLAT WASHER (K)

5/16" x 1-1/4"

HEX BOLT (D)

HEIGHT ADJUSTMENT

STRAP

ASSEMBLY OF HOPPER BAG

1. (Figure 11)Turnarearhoppertubesothatthebrace

holesinthemiddleofthetubeface down.Slidethe

tubethroughthetwoloopssewntothetoprearseam

insidethehopperbag.

2. (Figure 12) Insert the two upper hopper side tubes

throughthestitchedapsoneachsideofthehopper

bag.

3. (Figure 12)Assembletheendsoftherearhoppertube

ontotheendsoftheupperhoppersidetubes.Fasten

togetherusingplasticplugs(Z).

UPPER HOPPER

SIDE TUBE

PLASTIC PLUG (Z)

REAR HOPPER TUBE

(brace holes on bottom)

INNER BAG LOOPS

ENGLISH

4. (Figure 13)Turnthesecondrearhoppertubesothatthe

braceholesinthemiddleofthetubeface up.Assemble

theendsoftherearhoppertubeontotheendsofthe

lowerhoppersidetubes.Fastentogetherusingplastic

plugs (Z).

LOWER

HOPPER

SIDE TUBE

PLASTIC PLUG (Z)

REAR HOPPER TUBE

(brace holes on top)

14. (Figure 10) Place the star washer (L) between the

heightadjustmenthandleandtheheightadjustmenet

strap. Insert the 5/16" x1" carriage bolt (F) through

theheightadjustmenthandle,thestarwasherandthe

heightadjustmentstrap.Assemblea5/16"atwasher

(K)andtheplasticknob(X)ontotheendofthebolt.

5/16" FLAT

WASHER (K)

5/16" x 1"

CARRIAGE BOLT (F)

PLASTIC KNOB (X)

STAR WASHER (L)

(between strap and handle)

IMPORTANT: Do notoverbendthesupportrodsduring

thefollowingstep.Overbendingwillcausethesteelrods

to loose supporting tension.

10. (Figure 17)Tipthehopperontoit'sbacktoassemble

thetwohoppersupportrods.Placetheendsofeach

rodintotheupperandlowerrearhoppertubes,bending

therodjustenoughtotintotheholesinthetubes.

SUPPORT

RODS

7. (Figure 15)Insertthebagframestrapintothestitched

sleevealongthefrontedgeofthebagbottom.

8. (Figure 15)Assemblethebagframestraptothelower

hoppersidetubesusingtwo1/4"x1-1/8"clevispins

(P)and3/32"haircotterpins(N).

SNAP

FLAP

FIGURE 14

9. (Figure 16)Securethebagcornersaroundthelower

hoppersidetubesbysnappingthebagapstothebag

bottomonbothsides.

5. (Figure 14)Placetheassembledlowerhoppertubes

intothebottomofthehopperbag

6. (Figure 14)Attachtheendsofthelowerhopperside

tubestotheinsideoftheupperhoppersidetubesusing

two3/8"x1/2"clevispins(O)insertedfromtheinside,

andtwo3/32"haircotterpins(N).

LOWER HOPPER

SIDE TUBE

HOPPER BAG

BOTTOM

UPPER HOPPER

SIDE TUBE

3/8" x 1/2"

CLEVIS PIN (O)

3/32" HAIR

COTTER PIN (N)

1/4" x 1-1/8"

CLEVIS PIN (P)

3/32" HAIR

COTTER PIN (N)

BAG FRAME STRAP

ENGLISH

14. (Figure 20)Securetheropetothetopcenterofthe

hopperbagframe.

15. (Figure 21)Toassemblethehopperbagtothesweeper,

slidetheendsofthebagarmtubesintotheendsofthe

sweeper'shitchtubesandsecurewithtwo1/4"x1-3/4"

clevispins(Q)and3/32"haircotterpins(N).

LOWER HOLE

3/32" HAIR

COTTER PIN (N)

3/8" x 3"

CLEVIS PIN (R)

BAG ARM TUBE

VINYL CAP (V)

ENGLISH

UPPER HOLE

LOWER HOLE

UPPER HOPPER SIDE TUBE

11. (Figure 18)Feelalongthestitchedaponthehopper

bagtolocatethelowerholeineachupperhopperside

tube.Pierceaholethroughbothsidesofthestitched

apsinalignmentwiththelowerhole.

12. (Figure 19)Inserta3/8"x 3" clevispin (R) through

thelowerholeineachupperhoppersidetube.Next,

assembleabagarmtube(pointingindirectionshown)

ontoeachclevispinandsecureitwitha3/32"haircotter

pin (N).

13. (Figure 19)Assembleavinylcap(V)ontotheendof

eachbagarmtube.

BAG ARM TUBE

1/4" x 1-3/4"

CLEVIS PIN (Q)

3/32" HAIR

COTTER PIN (N)

ATTACHING SWEEPER HITCH TO TRACTOR

(Figures 22, 23, 24)

1. Placethetractorandsweeperonaatlevelsurface.

2. Setthesweeperheightadjustmenthandletoaboutthe

middleofitsadjustmentrange.

3. Attachthesweeperhitchbracketstothetractorhitch,

arrangingthe3/4"spacerstomakethebottomofthe

sweeperbagaslevelwiththegroundaspossible.See

gure23fortractorhitchesthatare11"to13"above

theground.Seegure24fortractorhitchesthatare8"

to11"abovetheground.

IMPORTANT: Forbestperformance,the bottomofthe

sweeperbagshouldbeaslevelwiththegroundaspossible

withatleast5"groundclearance.Seegure22.

Tractor hitches with 8" to 11" ground clearance.

2423

Tractor hitches with 11" to 13" ground clearance.

TRACTOR HITCH

8"-11"

TRACTOR HITCH

11"-13"

ENGLISH

5" Min.

Aerosmith Rocks

HOW TO USE YOUR SWEEPER

BRUSH HEIGHT ADJUSTMENT

 Toadjustyoursweeperbrushestothebestoperating

height, loosen the adjustment knob and push down

ontheheightadjustmentlevertoraisethebrush.Best

adjustmentiswhenthebrushsettingis1/2"downinto

the grass. Always mow the grass to an even height

beforesweeping.

SWEEPING SPEED

 Tryastartingspeedofapproximately3m.p.h.(thirdgear

onmosttractors).Dependingontheconditions,itmay

benecessarytoadjustthesweepingspeedinorderto

achievebestresults.

DUMPING OF SWEEPER

 Yoursweepercan be dumped easily without getting

offoftheriderortractor.Simplypulltheropeforward

todumpthehopper.Alwaysemptyhopperaftereach

use.

CAUTION: Keep sweeper away from fire.

Excessive heat can damage the brushes and

hopper bag and could cause the bag and its

contentstoburn.

CAUTION: Never attachthehopperropetoany

partofyourbodyorclothing!Never hold onto

theropewhiletowingthesweeper!Attach the

ropetothetowingvehicletokeepitawayfrom

wheelsandrotatingparts.

OPERATION

CUSTOMER RESPONSIBILITIES

1. Checkforloosefastenersbeforeeachuse.

2. Cleanthesweeperaftereachuse.

 a. Cleansweeperhousingwithasoftbrushorcloth.

 b. Cleandebrisfromhopperbagwithabrushor 

 broom.

 c. Removeanymaterialwhichhaswrappedaround

brushesorendsofbrushshaft.

3. Inspectforwornordamagedparts,suchasbrushes

andwheelsbeforeeachuse.Replaceasnecessary.

MAINTENANCE

5. Lubricate the wheelbearings eachseason. Remove

thehubcapandapplyafewdropsoflightweightoil.

6. (Figure 26)Everytwoyears,removethewheelsand

cleanthegearsfoundinsidethewheelhousing.After

cleaning,lubricatethegearswithanevencoatoflight

grease.Toremovethewheel,popoffthehubcapand

removethelocknutandatwasher.

1. Cleanthesweeperandhopperbagthoroughlytohelp

prevent rust and mildew.

2. Tocollapsethehopperbagforstorage,removethetwo

hoppersupportrodsfromtherearofthehopper.

3. Store in a dry area.

CAUTION: Before storing the sweeper,

always empty the hopper bag to avoid

spontaneouscombustion.

STORAGE

4. (Figure 25)Lubricatethebrushshaftbearingtwicea

yearwithafewdropsoflightweightoil.

ENGLISH

HEIGHT ADJUSTMENT SLOT

HEX BOLT

OIL BEARINGS HERE

FLAT WASHER

HEX BOLT FLAT WASHER

FLAT WASHER

HEX LOCK NUT

HUB CAP

SPACER

WHEEL GEAR AND PAWL SERVICE

IMPORTANT: Do notremovebothwheelsatthesame

timetoavoidmixingofparts.(TheR.H.andL.H.ratchet

gearsarenotinterchangeable.)Make notesontheposition

ofwashersandsnapringsduringdisassembly.

1. Remove only onewheelfromthesweeper.

2. Removetheretainingringsandwasherswhichholdthe

ratchetgearontothebrushshaft.

3. (Figure 28)Removethegearbyslidingitoffthebrush

shaft.(Lookforthedrivepin,whichmayfalloutofthe

brushshaftwhentheratchetgearisremoved.)

4. Toreassemble,insertthedrivepinthroughthehole

neartheendofthebrushshaft.Makesurethepinslides

backandfortheasilyintheshaft.

5. Lightlygreasetheshaftandlltheratchetgearwith

grease. Assemble the ratchet gear back onto the

shaft.

6. Lightlygreasetheaxleandthegearteethonthewheel,

andthenreassemblethewheel.Thebrushesshould

rotate onlyduringforwardrotationofthewheel.Ifthe

brushesaredriven(rotated)bybothforwardandreverse

rotationofthewheel,thedrivepinisjamminginthe

ratchetgear.Disassembletocleanandlubricatethe

drivepinandtheratchetgear.

7. Removethesecondwheelandrepeattheprocedure.

BRUSH REPLACEMENT

NOTE: Brushreplacementshouldbedoneonebrushat

a time.

1. Removethehopperbagfromthesweeper.

2. (Figure 27)Loosenthehexboltsandlocknutsontwo

singlebrushretainerswhichclamponebrushtothe

doublebrushretainers.Do Not loosenorremovethe

bolts which fasten the doublebrushretainers tothe

brushshaft.

3. (Figure 27)Slidethebrushoutoftheretainers,noting

onwhichsideofthebrushthebristlesoverlap.

4. (Figure 27)Installnewbrush,makingsurethebristles

overlaponthesamesideofthebrushasbefore.

1.Brushessettoolow.

2. Brushesarejammed

3. Wheelsarejammed.

Wheelsskidwhensweeping. 1. Adjustheighttillbrushesare1/2"downintograss.

2. Stopsweeper.Removeobstruction.

3. Removeonewheelatatimetocheckforobstructionor

damage.RefertoServiceandAdjustmentssection.

SERVICE AND ADJUSTMENTS

TROUBLESHOOTING

ENGLISH

BRUSH ROTATION

OVERLAP

BRISTLES

OVERLAP

BRISTLES

SINGLE

BRUSH

RETAINERS

DOUBLE BRUSH RETAINER

BRUSH

SHAFT

RATCHET

GEAR

DRIVE

Page is loading ...

REPAIR PARTS FOR MODEL 45-03311 38" LAWNSWEEPER

the fastest way to purchase parts

www.speedepart.com

REF PART NO. QTY DESCRIPTION

1 40612 1 HitchTube,R.H.

2 40613 1 HitchTube,L.H.

3 23353 1 Pin,Hitch

4 23368 2 Tube,HitchSpacer

5 43343 1 HairpinCotter,1/8"#4

7 C-9M5732 8 Rivet,Pop

9 43182 4 Bolt,Hex5/16-18x3/4"

10 65578 1 SweeperHousingAssembly

11 23336 2 Washer,Special

12 68208 1 HeightAdjustmentTubeAssembly

13 43063 2 Bolt,Hex5/16-18x1"

14 25408 1 Bushing,Spacer

15 43840 1 Bolt,Hex5/16-18x1-1/4"

16 44732 1 Washer,Star

17 R19212113 6 Washer,5/8"SAE

18 1629-56 2 Retainer,DustCover

19 44910 2 Bushing,BrushShaft

20 24085 1 BrushShaft

21 43905 4 Brush

22 43012 8 Bolt,Hex1/4-20x3/4"Lg.

23 47189 12 Nut,Nylock1/4-20

24 23580 4 Retainer,Brush(Double)

25 23581 8 Retainer,Brush(Single)

26 44125 2 Washer,Flat.625"x1.0"x.03"

27 47046 2 Dowel Pin (Drive)

29 47810 15 Nut,Nylock5/16-18

30 48702 2 Spacer,.41I.D".x1-1/4"O.D.x.6"

31 44006 2 Washer,Flat.849"x.598"x.025"

32 46219 2 Spacer,.78I.D".x1-1/4"O.D.x.5"

33 1650-21 2 Ring,Retaining.594"

34 40001 6 Washer,Shim1-1/8"x.594"x.025"

35 141 4 Washer,Flat1-1/2"x.375"x.062"

36 1038 2 Nut,NylockJam3/8-24Thread

37 2674-32 2 HubCap

38 44961 2 Bolt,Hex3/8-24x3-1/4"Lg.

REF PART NO. QTY DESCRIPTION

39 23400 3 Bushing,Pivot

40 43886 1 Gear,PinionR.H.(notshown)

41 43885 1 Gear,PinionL.H.

42 43661 4 Bolt,Hex1/4-20x1"Lg.

43 64578 2 Ass'y,DustCover

44 48469 2 Tube,HopperFrame(Rear)

45 48466 2 Tube,UpperHopperFrame(Front)

46 48727 2 Tube,LowerHopperFrame(Front)

47 48402 4 Plastic Plug

48 48403 1 Hopper Bag

49 48366 2 ClevisPin,3/8"x1/2"

50 23352 1 Strap,BagFrame

51 43926 2 Rod,HopperSupport

52 43737 1 Hopper Rope

53 44481 2 Cap,Vinyl

54 24979 1 Strap,HeightAdjustment

55 23687 1 Bracket,Hitch

56 24192 1 Bracket,Hitch(Straight)

57 26243 1 Handle,HeightAdjustment

58 40620 2 Tube,BagArm

59 43513 2 Pin,Clevis3/8"x3"

60 49946 2 WheelAss'y.(withbearings)

61 741-0249 4 WheelBearing

62 44292 2 Bolt,Hex5/16-18x2-1/2"Lg.

63 44180 2 Bolt,Hex5/16-18x2"Lg.

64 43681 4 Bolt,Carriage5/16-18x1-1/2"

65 43055 8 HairpinCotter,3/32"#3

66 43720 1 Knob,Wing5/16-18Thread

67 44326 1 Bolt,Carriage5/16-18x1"

68 43081 4 Washer,Flat5/16"Std.Wrt.

69 43943 1 Grip,HeightAdjust

70 46867 2 ClevisPin,1/4"x1-3/4"Lg.

71 48365 2 ClevisPin,1/4"x1-1/8"

40634 1 Owners Manual

the fastest way to purchase parts

www.speedepart.com

REPAIR PARTS

Agri-Fab,Inc.

809SouthHamilton

Sullivan,IL.61951

217-728-8388

Agri-Fab 45-03311 User manual

Related papers

Other documents