Agri-Fab 45-03261 User manual

Brand: Agri-Fab

Model: 45-03261

Type: User manual

This manual is also suitable for

45-0331

PRINTED IN U.S.A. FORM NO. 40638 (REV. 03/17/08)

46" LAWNSWEEPER

BARREDORA DE CESPED DE 117 cm

BALAYEUSE DE 117 cm

OWNERS MANUAL

MANUAL DEL USUARIO

NOTICE D’UTILISATION

CAUTION:

Read Rules for

Safe Operation

and Instructions

Carefully

Model No.

Modelo No.

Modèle No.

45-03261

ATTENTION:

Lire et suivre attentivement

les instructions et

consignes de sécurité de

cette notice.

PRECAUCION:

Lea cuidadosamente

los Procedimientos e

Instrucciones para la

Operación Segura de la

Máquina.

• Safety

• Assembly

• Operation

• Maintenance

• Parts

• Seguridad

• Montaje

• Operación

• Mantenimiento

• PiezasdeRepuesto

• Sécurité

• Assemblage

• Fonctionnement

• Maintenance

• PiècesdeRechange

the fastest way to purchase parts

www.speedepart.com

™

Aerosmith Rocks

1. SweeperHousingAssembly

2. BagArmTube(2)

3. HitchTube,L.H.

4. HitchBracket

5. HitchBracket(Straight)

6. HeightAdjustmentStrap

7. HeightAdjustmentHandle

8. HitchTube,R.H.

9. Rope

10. Hopper Bag

11. UpperHopperSideTube(2)

12. RearHopperTube(2)

13. LowerHopperSideTube(2)

14. Hopper Pivot Rod

15. Hopper Support Rod (2)

1. ConjuntodeCarcazadelaBarredora

2. BrazodelTubodelaBolsa(2)

3. TubodeEnganche(ManoIzquierda)

4. MénsuladeEnganche

5. MénsuladeEnganche(Recta)

6. BandadeAjustedeAltura

7. ManijadeAjustedeAltura

8. TubodeEnganche(ManoDerecha)

9. Cuerda

10. Bolsa de la Tolva

11. TuboLateraldelaParteSuperiorde

la Tolva (2)

12. TubodelaPartePosteriordelaTolva(2)

13. TuboLateraldelaParteInferiorde

la Tolva (2)

14. Varilla Giratoria de la Golsa de la Tolva

15. Barra de Soporte de la Tolva (2)

1. Bâtidelabalayeuse

2. Tubedubrasdusac(2)

3. Tubed‘attelage,côtédroit

4. Support de l’attelage

5. Supportdel’attelage,droit

6. Étrierderéglagedelahauteur

7. Poignéederéglagedelahauteur

8. Tubed’attelage,côtédroit.

9. Cordage

10. Sacderécupérationdesdébris

11. Tubelatéralsupérieurdela

trémie (2)

12. Tubearrièredelatrémie(2)

13. Tubelatéralinférieurdela

trémie (2)

14. Tigedepivotdubacderamassage

15. Tiges de support de la trémie (2)

FRANÇAIS

ESPAÑOL

ENGLISH

CARTON CONTENTS (Loose Parts in Carton)

CONTENIDO DE LA CAJA(PartesSueltasenlaCaja)

CONTENU DU CARTON(PiècesenVracDansleCarton)

ENGLISH

A B C

F G

SHOWN FULL SIZE

NOT SHOWN FULL SIZE

V W X

REF QTY DESCRIPTION

A 2 HexBolt,5/16x3"Lg.

B 2 HexBolt,5/16x2-1/4"Lg.

C 4 CarriageBolt,5/16"x1-3/4"

D 1 HexBolt,5/16x1-1/4"Lg.

E 2 HexBolt,5/16"x1"

F 1 CarriageBolt,5/16"x1"

G 4 HexBolt,1/4"x1"

I 4 NylockNut,1/4"

J 11 NylockNut,5/16"

K 4 FlatWasher,5/16"

L 1 StarWasher

M 1 HairCotterPin,1/8"

N 6 HairCotterPin,3/32"

REF QTY DESCRIPTION

O 2 ClevisPin,3/8"x1/2"

P 2 ClevisPin,1/4"x1-1/8"

Q 2 ClevisPin,1/4"x1-3/4"

R 2 Palnut,3/8"

S 1 PivotBushing

T 1 SpacerBushing

U 2 HitchSpacer,3/4"

V 2 Vinyl Cap

W 1 Grip

X 1 Knob,Plastic

Y 1 HitchPin

Z 4 Plastic Plug

6. Vehicle braking and stability may be affected with

theattachmentofthissweeper.Donotllsweeperto

maximumcapacitywithoutcheckingthecapabilityofthe

towingvehicletosafelypullandstopwiththesweeper

attached.Stay off of steep slopes.

7. Stopandinspectvehicleandsweeperfordamageafter

strikinganobject.Repairanydamagebeforecontinuing

operation.

8. Keep sweeper away from re. Excessive heat can

damagethebrushesandhopperbagandcouldcause

thebaganditscontentstoburn.

9. Beforestoringthesweeper,alwaysemptythehopper

bagtoavoidspontaneouscombustion.

10. Follow maintenance and lubrication instructions as

outlinedinthemaintenancesectionofthismanual.

1. Readthevehicleandsweeperownersmanualsand

knowhowtooperateyourvehicleandsweeperbefore

usingthissweeperattachment.Alwaysinstructother

usersbeforetheyoperatethesweeper.

2. Donotpermitchildrentooperatesweeper.

3. Do not permit anyone to ride on sweeper.

4. Neverattachthehopperropetoanypartofyourbody

orclothing!Neverholdontotheropewhiletowingthe

sweeper!Attachtheropetothetowingvehicletokeep

itawayfromwheelsandrotatingparts.

5. Operate the sweeper at reduced speed on rough

terrain,nearditchesandonhillsidestopreventlossof

control.

Remember,anypowerequipmentcancauseinjuryifoperatedimproperlyoriftheuserdoesnotunderstandhowtooperate

theequipment.Exercisecautionatalltimeswhenusingpowerequipment.

SAFETY RULES

ENGLISH

Lookforthissymboltopointoutimportantsafetyprecautions.Itmeans—Attention!!

Become alert!! Your safety is involved.

TOOLS REQUIRED FOR ASSEMBLY

(2)  7/16"OpenEndorBoxEndWrenches

(2)  1/2"OpenEndorBoxEndWrenches

(1) Hammer

ASSEMBLY

Allloosepartsareshownonpage2.Fastenersintheparts

bagareshownfullsizeonpage3.

Removethehardwarepackandallloosepartsfromthe

cartonandverifythatallthepartsandfastenersshownon

pages 2 and 3 are included.

ASSEMBLY OF SWEEPER

Note: Righthand(R.H.)andlefthand(L.H.)aredetermined

fromtheoperator'spositionwhileseatedonthetractor.

1. (Figure 1)Eachbrushassemblyhasonebrushretainer

markedwitheitherredorblackink.Layoutthebrush

assembliesasshownsothatthebrushretainersmarked

withinkareinthemiddlewiththeredoneontheright

andtheblackoneontheleft.

ENGLISH

OVERLAP BRISTLES

BRUSH RETAINER

MARKED BLACK

BRUSH RETAINER

MARKED RED

IMPORTANT:Theoverlapbristlesatthebottomofeachbrush

helpsupportthebacksideofthebrushforbettersweeper

performance.Besurethesweeperisturnedasshownin

gures2and3tocorrectlyassemblethebrushes.

2. (Figure 2) Attach the brush assembly with the red

brushretainertotherightendofthebrushshaftusing

two1/4"x1"hexbolts(G)and1/4"nylocknuts(I).The

brushretainermarkedwithredinkmustbeplacedto

themiddleofthesweeper.

BRUSH RETAINER

MARKED RED

OVERLAP

BRISTLES

1/4" x 1"

HEX BOLT (G)

1/4" NYLOCK NUT (I)

BRUSH RETAINER

MARKED RED

5/16" x 1-3/4"

CARRIAGE BOLT (C)

5/16" NYLOCK NUT (J)

5. Cutofftheplastictiethatholdstheheightadjustment

tubeinplace.

6. (Figure 4)AssembletheR.H.hitchtubetothesweeper

housingusingtwo5/16"x1-3/4"carriagebolts(C),and

two5/16"nylocknuts(J).Do not tighten yet. Repeat

fortheL.H.hitchtube.

7. (Figure 5)Fastenthehitchtubestogetherusingtwo

5/16"x3"hexbolts(A)and5/16"nylocknuts(J).Do

not tighten yet.

5/16" x 3"

HEX BOLT (A)

5/16"

NYLOCK NUT (J)

3. (Figure 3)Attachthebrushassemblywiththeblack

brushretainertotheleftendofthebrushshaftusing

two1/4"x1"hexbolts(G)and1/4"nylocknuts(I).The

brushretainermarkedwithblackinkmustbeplacedto

themiddleofthesweeper.

4. (Figure 3)Turn a wheelto rotatethe brushes. (The

wheelsdrivethebrushes in onedirectiononly.)The

overlapbristlesshouldbeonthebacksideofthebrush

as it rotates.

1/4" x 1"

HEX BOLT (G)

1/4" NYLOCK NUT (I)

BRUSH RETAINER

MARKED BLACK

ENGLISH

11. (Figure 8) Assemble the height adjustment handle

totheinsideofthebracketontheendoftheheight

adjustmenttube.Usetwo5/16"x1"hexbolts(E),5/16"

atwashers(K)and5/16"nylocknuts(J).Tighten.

12. (Figure 8) Assemble the grip (W) onto the height

adjustmenthandle.

13. (Figure 9)Assembleontoa5/16" x1-1/4"hexbolt

(D)intheorderlisted,a5/16"atwasher(K),thepivot

bushing(S),theheightadjustmentstrapandthespacer

bushing(T).Inserttheboltthroughtheupperpartof

thedoubleholeintheendofthesweeperhousingand

secureitwitha5/16"nylocknut(J).Tighten.

If your tractor hitch has 10" to 13" ground clearance refer

to gure 6. If your tractor hitch has 8" to 10" ground

clearance refer to gure 7.

8. (Figure 6 or 7)Assemblethehitchbracketstothehitch

tubesusingtwo5/16"x2-1/14"hexbolts(B)and5/16"

nylocknuts(J).Theboltsshouldstraddlethefronthitch

tubebolt.Do not tighten yet.

9. Atthistimetightenthefourboltsfasteningthehitch

tubestothesweeperhousing.Next,tightenthetwobolts

fasteningtheendsofthehitchtubestogether.Finally,

tightenthetwoboltsfasteningthehitchbracketstothe

hitchtubes.

10. (Figure 6or 7)Assemblethehitchpin(Y),two3/4"hitch

spacers(U)andthe1/8"haircotterpin(M)tothehitch

brackets.

5/16" x 2-1/4"

HEX BOLT (B)

5/16" NYLOCK

NUT (J)

3/4" SPACER (U)

HITCH BRACKET

(STRAIGHT)

1/8" HAIR

COTTER PIN (M)

HITCH PIN (Y)

5/16" NYLOCK NUT (J)

HEIGHT

ADJUSTMENT

HANDLE

GRIP (W)

5/16" FLAT WASHER (K)

5/16" x 1" HEX BOLT (E)

5/16" x 2-1/4"

HEX BOLT (B)

5/16" NYLOCK

NUT (J)

3/4" SPACER (U)

HITCH PIN (Y)

HITCH BRACKET

(STRAIGHT)

1/8" HAIR

COTTER PIN (M)

HITCH BRACKET

PIVOT BUSHING (S)

5/16" NYLOCK NUT (J)

SPACER BUSHING (T)

5/16" FLAT WASHER (K)

5/16" x 1-1/4"

HEX BOLT (D)

HEIGHT ADJUSTMENT

STRAP

ASSEMBLY OF HOPPER BAG

1. (Figure 11)Turnarearhoppertubesothatthebrace

holesinthemiddleofthetubeface down.

2. (Figure 12) Insert the two upper hopper side tubes

throughthestitchedapsoneachsideofthehopper

bag.

3. (Figure 12)Assembletheendsoftherearhoppertube

ontotheendsoftheupperhoppersidetubes.Fasten

togetherusingplasticplugs(Z).

ENGLISH

REAR HOPPER TUBE

(brace holes on bottom)

UPPER HOPPER

SIDE TUBE

PLASTIC PLUG (Z)

14. (Figure 10) Place the star washer (L) between the

heightadjustment handle andtheheight adjustment

strap. Insert the 5/16" x1" carriage bolt (F) through

theheightadjustmenthandle,thestarwasherandthe

heightadjustmentstrap.Assemblea5/16"atwasher

(K)andtheplasticknob(X)ontotheendofthebolt.

5/16" FLAT

WASHER (K)

5/16" x 1"

CARRIAGE BOLT (F)

PLASTIC KNOB (X)

STAR WASHER (L)

(between strap and handle)

7. (Figure 15)Insertthebagframestrapintothestitched

sleevealongthefrontedgeofthebagbottom.

8. (Figure 15)Assemblethebagframestraptothelower

hoppersidetubesusingtwo1/4"x1-1/8"clevispins

(P)and3/32"haircotterpins(N).

FIGURE 14

9. (Figure 16)Securethebagcornersaroundthelower

hoppersidetubesbysnappingthebagapstothebag

bottomonbothsides.

4. (Figure 13)Turnthesecondrearhoppertubesothatthe

braceholesinthemiddleofthetubeface up.Assemble

theendsoftherearhoppertubeontotheendsofthe

lowerhoppersidetubes.Fastentogetherusingplastic

plugs (Z).

5. (Figure 14)Placetheassembledlowerhoppertubes

intothebottomofthehopperbag

6. (Figure 14)Attachtheendsofthelowerhopperside

tubestotheinsideoftheupperhoppersidetubesusing

two3/8"x1/2"clevispins(O)insertedfromtheinside,

andtwo3/32"haircotterpins(N).

ENGLISH

LOWER

HOPPER

SIDE TUBE

PLASTIC PLUG (Z)

REAR HOPPER TUBE

(brace holes on top)

LOWER HOPPER

SIDE TUBE

HOPPER BAG

BOTTOM

UPPER HOPPER

SIDE TUBE

3/8" x 1/2"

CLEVIS PIN (O)

3/32" HAIR

COTTER PIN (N)

1/4" x 1-1/8"

CLEVIS PIN (P)

3/32" HAIR

COTTER PIN (N)

BAG FRAME STRAP

SNAP

FLAP

IMPORTANT: Do notoverbendthesupportrodsduring

thefollowingstep.Overbendingwillcausethesteelrods

to loose supporting tension.

13. (Figure 18)Tipthehopperontoit'sbacktoassemble

thetwohoppersupportrods.Placetheendsofeach

rodintotheupperandlowerrearhoppertubes,bending

therodjustenoughtotintotheholesinthetubes.

10. (Figure 17)Insertthehopperpivotrodthroughtheupper

hoppersidetubes,thebagarmtubesandthestitched

sleeveatthefrontofthewindscreen.

11. Usingahammer,assembleeachpalnut(R)ontoone

endofthehopperpivotrodwhilebracingtheotherend

againstasolidobject.

12. (Figure 17)Assembleavinylcap(V)ontotheendof

eachbagarmtube.

14. (Figure 19)Securetheropetothetopcenterofthe

hopperbagframe.

15. (Figure 20)Toassemblethehopperbagtothesweeper,

slidetheendsofthebagarmtubesintotheendsofthe

sweeper'shitchtubesandsecurewithtwo1/4"x1-3/4"

clevispins(Q)and3/32"haircotterpins(N).

ENGLISH

HOPPER

PIVOT ROD

BAG ARM TUBE

VINYL CAP (V)

PALNUT (R)

SUPPORT

RODS

BAG ARM TUBE

1/4" x 1-3/4"

CLEVIS PIN (Q)

3/32" HAIR

COTTER PIN (N)

ATTACHING SWEEPER HITCH TO TRACTOR

(Figures 21, 22, 23)

1. Placethetractorandsweeperonaatlevelsurface.

2. Setthesweeperheightadjustmenthandletoaboutthe

middleofitsadjustmentrange.

3. Attachthesweeperhitchbracketstothetractorhitch,

arrangingthe3/4"spacerssothatthebottomofthe

sweeperbagisapproximatelyleveland5"to7"above

theground.Seegure22fortractorhitchesthatare

10"to13"abovetheground.Seegure23fortractor

hitchesthatare8"to10"abovetheground.

IMPORTANT: Forbestperformance,the bottomofthe

sweeperbagshouldbeapproximatelyleveland5"to7"off

thegroundasshowningure21.

Tractor hitches with 8" to 10" ground clearance.

Tractor hitches with 10" to 13" ground clearance.

ENGLISH

5" - 7"

Aerosmith Rocks

TRACTOR HITCH

10"-13"

TRACTOR HITCH

8"-10"

HOW TO USE YOUR SWEEPER

BRUSH HEIGHT ADJUSTMENT

 Toadjustyoursweeperbrushestothebestoperating

height, loosen the adjustment knob and push down

ontheheightadjustmentlevertoraisethebrush.Best

adjustmentiswhenthebrushsettingis1/2"downinto

the grass. Always mow the grass to an even height

beforesweeping.

SWEEPING SPEED

 Tryastartingspeedofapproximately3m.p.h.(thirdgear

onmosttractors).Dependingontheconditions,itmay

benecessarytoadjustthesweepingspeedinorderto

achievebestresults.

DUMPING OF SWEEPER

 Yoursweeper can be dumped easilywithout getting

offoftheriderortractor.Simplypulltheropeforward

todumpthehopper.Alwaysemptyhopperaftereach

use.

CAUTION: Keep sweeper away from fire.

Excessive heat can damage the brushes and

hopper bag and could cause the bag and its

contentstoburn.

CAUTION: Never attachthehopperropetoany

partofyourbodyorclothing!Never hold onto

theropewhiletowingthesweeper!Attach the

ropetothetowingvehicletokeepitawayfrom

wheelsandrotatingparts.

OPERATION

CUSTOMER RESPONSIBILITIES

1. Checkforloosefastenersbeforeeachuse.

2. Cleanthesweeperaftereachuse.

 a. Cleansweeperhousingwithasoftbrushorcloth.

 b. Cleandebrisfromhopperbagwithabrushor 

 broom.

 c. Removeanymaterialwhichhaswrappedaround

brushesorendsofbrushshaft.

3. Inspectforwornordamagedparts,suchasbrushes

andwheelsbeforeeachuse.Replaceasnecessary.

MAINTENANCE

5. Lubricate the wheelbearings eachseason. Remove

thehubcapandapplyafewdropsoflightweightoil.

6. (Figure 25)Everytwoyears,removethewheelsand

cleanthegearsfoundinsidethewheelhousing.After

cleaning,lubricatethegearswithanevencoatoflight

grease.Toremovethewheel,popoffthehubcapand

removethelocknutandatwasher.

1. Cleanthesweeperandhopperbagthoroughlytohelp

prevent rust and mildew.

2. Tocollapsethehopperbagforstorage,removethetwo

hoppersupportrodsfromtherearofthehopper.

3. Store in a dry area.

CAUTION: Before storing the sweeper,

always empty the hopper bag to avoid

spontaneouscombustion.

STORAGE

4. (Figure 24)Lubricatethebrushshaftbearingtwicea

yearwithafewdropsoflightweightoil.

ENGLISH

HEIGHT ADJUSTMENT SLOT

HEX BOLT

OIL BEARINGS HERE

FLAT WASHER

HEX BOLT FLAT WASHER

FLAT WASHER

HEX LOCK NUT

HUB CAP

SPACER

WHEEL GEAR AND PAWL SERVICE

IMPORTANT: Do notremovebothwheelsatthesame

timetoavoidmixingofparts.(TheR.H.andL.H.ratchet

gearsarenotinterchangeable.)Make notesontheposition

ofwashersandsnapringsduringdisassembly.

1. Remove only onewheelfromthesweeper.

2. Removetheretainingringsandwasherswhichholdthe

ratchetgearontothebrushshaft.

3. (Figure 27)Removethegearbyslidingitoffthebrush

shaft.(Lookforthedrivepin,whichmayfalloutofthe

brushshaftwhentheratchetgearisremoved.)

4. Toreassemble,insertthedrivepinthroughthehole

neartheendofthebrushshaft.Makesurethepinslides

backandfortheasilyintheshaft.

5. Lightlygreasetheshaftandlltheratchetgearwith

grease. Assemble the ratchet gear back onto the

shaft.

6. Lightlygreasetheaxleandthegearteethonthewheel,

andthenreassemblethewheel.Thebrushesshould

rotate onlyduringforwardrotationofthewheel.Ifthe

brushesaredriven(rotated)bybothforwardandreverse

rotationofthewheel,thedrivepinisjamminginthe

ratchetgear.Disassembletocleanandlubricatethe

drivepinandtheratchetgear.

7. Removethesecondwheelandrepeattheprocedure.

BRUSH REPLACEMENT

NOTE: Brushreplacementshouldbedoneonebrushat

a time.

1. Removethehopperbagfromthesweeper.

2. (Figure 26)Loosenthehexboltsandlocknutsontwo

singlebrushretainerswhichclamponebrushtothe

doublebrushretainers.Do Not loosenorremovethe

bolts which fasten the doublebrushretainers tothe

brushshaft.

3. (Figure 26)Slidethebrushoutoftheretainers,noting

onwhichsideofthebrushthebristlesoverlap.

4. (Figure 26)Installnewbrush,makingsurethebristles

overlaponthesamesideofthebrushasbefore.

1.Brushessettoolow.

2. Brushesarejammed

3. Wheelsarejammed.

Wheelsskidwhensweeping. 1. Adjustheighttillbrushesare1/2"downintograss.

2. Stopsweeper.Removeobstruction.

3. Removeonewheelatatimetocheckforobstructionor

damage.RefertoServiceandAdjustmentssection.

SERVICE AND ADJUSTMENTS

TROUBLESHOOTING

ENGLISH

BRUSH ROTATION

OVERLAP

BRISTLES

OVERLAP

BRISTLES

SINGLE

BRUSH

RETAINERS

DOUBLE BRUSH RETAINER

BRUSH

SHAFT

RATCHET

GEAR

DRIVE

Page is loading ...

REPAIR PARTS FOR MODEL 45-03261 46" LAWNSWEEPER

the fastest way to purchase parts

www.speedepart.com

REF PART NO. QTY DESCRIPTION

1 40618 1 HitchTube,R.H.

2 40619 1 HitchTube,L.H.

3 23353 1 Pin,Hitch

4 23368 2 Tube,HitchSpacer

5 43343 1 HairpinCotter,1/8"#4

7 C-9M5732 8 Rivet,Pop

9 43182 4 Bolt,Hex5/16-18x3/4"

10 65580 1 SweeperHousingAssembly

11 23336 2 Washer,Special

12 66152 1 HeightAdjustmentTubeAssembly

13 43063 2 Bolt,Hex5/16-18x1"

14 25408 1 Bushing,Spacer

15 43840 1 Bolt,Hex5/16-18x1-1/4"

16 44732 1 Washer,Star

17 R19212113 2 Washer,5/8"SAE

18 1629-56 2 Retainer,DustCover

19 44910 2 Bushing,BrushShaft

20 24929 1 BrushShaft

21 48600 4 Brush

22 43012 8 Bolt,Hex1/4-20x3/4"Lg.

23 47189 12 Nut,Nylock1/4-20

24 23580 4 Retainer,Brush(Double)

25 23581 8 Retainer,Brush(Single)

26 44008 2 Washer,Flat1-1/8"x.78"x.025"

27 47046 2 Dowel Pin (Drive)

29 47810 15 Nut,Nylock5/16-18

30 44911 2 Spacer,.39I.D".x1-1/4"O.D.x.5"

44917 2 Palnut,3/8"

32 46219 2 Spacer,.78I.D".x1-1/4"O.D.x.5"

33 1650-21 4 Ring,Retaining.594"

34 40007 2 Washer,Shim1-1/4"x.594"x.025"

35 141 4 Washer,Flat1-1/2"x.375"x.062"

36 1038 2 Nut,NylockJam3/8-24Thread

37 2674-32 2 HubCap

38 44961 2 Bolt,Hex3/8-24x3-1/4"Lg.

REF PART NO. QTY DESCRIPTION

39 23400 3 Bushing,Pivot

40 48652 1 Gear,PinionR.H.(notshown)

41 48651 1 Gear,PinionL.H.

42 43661 4 Bolt,Hex1/4-20x1"Lg.

43 64559 2 Ass'y,DustCover

44 47477 2 Tube,HopperFrame(Rear)

45 48466 2 Tube,UpperHopperFrame(Front)

46 48726 2 Tube,LowerHopperFrame(Front)

47 48402 4 Plastic Plug

48 48384 1 Hopper Bag

49 48366 2 ClevisPin,3/8"x1/2"

50 24189 1 Strap,BagFrame

51 43926 2 Rod,HopperSupport

52 43737 1 Hopper Rope

53 44481 2 Cap,Vinyl

54 24979 1 Strap,HeightAdjustment

55 23687 1 Bracket,Hitch

56 24192 1 Bracket,Hitch(Straight)

57 26243 1 Handle,HeightAdjustment

58 40622 2 Tube,BagArm

59 46823 1 Rod,HopperBag

60 44985 2 Wheel&TireAss'y.(withbearings)

61 45088 4 WheelBearing

62 46782 2 Bolt,Hex5/16-18x3"Lg.

63 43224 2 Bolt,Hex5/16-18x2-1/4"Lg.

65 44215 4 Bolt,Carriage5/16-18x1-3/4"

66 43055 6 HairpinCotter,3/32"#3

67 43720 1 Knob,Wing5/16-18Thread

68 44326 1 Bolt,Carriage5/16-18x1"

69 43081 4 Washer,Flat5/16"Std.Wrt.

70 43943 1 Grip,HeightAdjust

71 46867 2 ClevisPin,1/4"x1-3/4"Lg.

72 48365 2 ClevisPin,1/4"x1-1/8"

40638 1 Owners Manual

the fastest way to purchase parts

www.speedepart.com

REPAIR PARTS

Agri-Fab,Inc.

809SouthHamilton

Sullivan,IL.61951

217-728-8388

www.agri-fab.com

Thisdocument(ormanual)isprotectedundertheU.S.CopyrightLawsandthecopyrightlawsofforeigncountries,

pursuanttotheUniversalCopyrightConventionandtheBerneconvention.Nopartofthisdocumentmaybereproduced

ortransmittedinanyformorbyanmeans,electronicormechanical,includingphotocopyingorrecording,orbyany

informationstorageorretrievalsystem,withouttheexpresswrittenpermissionofAgri-Fab,Inc.Unauthorizedusesand/or

reproductionsofthismanualwillsubjectsuchunauthorizedusertocivilandcriminalpenaltiesasprovidedbytheUnited

StatesCopyrightLaws.

Agri-Fab 45-03261 User manual

Brand: Agri-Fab

Model: 45-03261

Type: User manual

This manual is also suitable for

45-0331

Download PDF

report

in other languages

français: Agri-Fab 45-03261 Manuel utilisateur
español: Agri-Fab 45-03261 Manual de usuario

Agri-Fab 45-03261 User manual

This manual is also suitable for

Agri-Fab 45-03261 User manual

in other languages

Related papers

Other documents