Minka Lavery 4130-84 Installation guide

Brand: Minka Lavery

Model: 4130-84

Type: Installation guide

Minka Lavery 4130-84 is a lighting fixture designed for indoor use. The fixture includes a crossbar, ground screw, two mounting screws, two junction box screws, canopy, finials, cup, glass, socket, and screws for assembly. The fixture requires a single light bulb (not included) and can be adjusted to the desired height using the screw (K) and fixture wire (L). It is important to note that the maximum wattage of the light bulb should not be exceeded. Before installing the fixture, shut off the power at the fuse box or circuit breaker box.

Minka Lavery 4130-84 is a lighting fixture designed for indoor use. The fixture includes a crossbar, ground screw, two mounting screws, two junction box screws, canopy, finials, cup, glass, socket, and screws for assembly. The fixture requires a single light bulb (not included) and can be adjusted to the desired height using the screw (K) and fixture wire (L). It is important to note that the maximum wattage of the light bulb should not be exceeded. Before installing the fixture, shut off the power at the fuse box or circuit breaker box.

INSTALLATION INSTRUCTIONS FOR 4130

WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

READ AND SAVE THESE INSTRUCTIONS

Fig.1

PREPATION (Fig. 1)

1. Shut off the power at the fuse box or circuit breaker

box. If necessary, remove the old fixture including the

mounting hardware.

2. Carefully remove the new fixture from the carton and

check that all parts are included as shown in the

illustration.

MOUNTING THE FIXTURE (Fig.1)

3. Thread the two mounting screws (A) (Size: #8-

32*1.4”L) part way into the crossbar (B). Secure

crossbar (B) to the junction box (not provided) with

junction box screws (C) (Size: #8-32*0.6”L). The length

of mounting screws (A) into crossbar (B) may be

adjusted if necessary. The side of the crossbar

marked “GND” must face out.

CONNECTING THE WIRES (Fig.2)

4. At this point, connect the electrical wires as shown in

Fig. 2, making sure that all wire connectors are

secured. If your outlet box has a ground wire

(green or bare copper) connect the fixture’s ground

wire to it. Otherwise, connect the fixture’s ground

wire directly to the mounting plate using the green

screw provided. After the wires are connected, tuck

them carefully inside the junction box.

COMPLETING THE INSTALLATION (Fig. 1)

5. Align canopy (D) over mounting screws (A) and

secure with finials (E).

6. Loosen the screws (F), and remove the cup (H).

7. Install the light bulb (not included) in accordance with

the fixture’s specifications. (DO NOT EXCEED THE

MAXIMUM WATTAGE!) (NE PAS DEPASSER LA

PUISSANCE NOMINALE MAXIMALE!)

8. Place the cup (H) onto the glass (J) and secure with

screws (I).

9. Raise the cup (H) over the socket (G) and secure with

screws (F).

Your installation is now complete. Return power to the

outlet box and test the fixture.

Note: Loosen the screw (K) and adjust to the

desired height of fixture wire (L), then

re-secure with screw (K).

Fig.2

Set#

-Crossbar

-Ground screw

-Mounting screw*2

-Junction box screws*2

A-016

1

Minka Lavery 4130-84 Installation guide

Brand: Minka Lavery

Model: 4130-84

Type: Installation guide

Minka Lavery 4130-84 is a lighting fixture designed for indoor use. The fixture includes a crossbar, ground screw, two mounting screws, two junction box screws, canopy, finials, cup, glass, socket, and screws for assembly. The fixture requires a single light bulb (not included) and can be adjusted to the desired height using the screw (K) and fixture wire (L). It is important to note that the maximum wattage of the light bulb should not be exceeded. Before installing the fixture, shut off the power at the fuse box or circuit breaker box.

Download PDF

Related papers

Other documents