PowerCage
™
MTP T AV and MTP R AV Board
Setup Guide
Continued on side 2.
1
The Extron
®
PowerCage MTP T AV and
MTP R AV are twisted pair transmitters and
receivers in a modular board format for the
PowerCage 1600 modular enclosure. They
transmit or receive composite video or
S-video and audio over CAT 5-type cable.
Both boards can be used with any CAT 5, 5e, or 6 cable, or Extron
Enhanced Skew-Free
™
A/V UTP cable for cable runs up to 1000 feet
(300 m). The boards mount in any of the 16 expansion slots at the rear of
the PowerCage 1600.
Refer to the PowerCage MTP T AV and MTP R AV User Guide and the
PowerCage 1600 Enclosure User Guide, available at www.extron.com.
NOTE: The hot-swappable, modular design allows for replacing or
upgrading boards in the field at any time, without having to
power down the system.
Installation
1. Select an open slot at the rear, or take out a blank plate by loosening the two
screws (top and bottom), and lifting the blank away.
NOTE: If a board is already in the slot, loosen the screws and remove the board.
2. Remove the new board from the box,
holding the board by the frame.
3. Hold the board with the signal connectors
towards you and the MTP AV board name
and LED at the top, and align the top and
bottom grooves of the board with the slide
posts in the selected enclosure slot.
4. Carefully slide the board into the slot,
aligning that the two tabs on the lower
front end of the board with the matching
ports in the enclosure. Push the board
firmly into place.
5. Tighten the screws to secure the board.
6. If applicable, repeat steps 1 through 5
for any other modular boards.
NOTE: Cover all empty board slots; do not leave them open. Using a tool, securely
fasten the screws for boards and blank panels after initial installation and
subsequent removal and replacement of the boards.
MONO
AUDIO OUTPUT
1 2
SHARP
GAIN
Y/VID
C
INPUT
PowerCage
MTP R AV
Tx Rx
HD/SDI INPUT HD/SDI OUTPUTS
MODE
PowerCage
FOX 3G HD-SDI
1 2
REMOTE
RS-232
RS-232
OVER FIBER
Tx Rx
Tx
ALARM
Rx
OUTPUT
RGB
PowerCage
FOX 4G RX RGB
Tx Rx
L R
AUDIO
5A MAX.
100-240V 50/60Hz
N15778
C
US
LISTED
1T23
I.T.E.
Screws
(2 per board)
1 2
REMOTE
RS-232
RS-232
OVER FIBER
Tx Rx
Tx
ALARM
Rx
OUTPUT
RGB
PowerCage
FOX 4G RX RGB
Tx Rx
L R
AUDIO
Align board and
slide into slot.
16 Available Single Board Slots or
8 Double Board Slots
Power
Supply
MTP R AV
MONO
AUDIO OUTPUT
1 2
SHARP
GAIN
Y/VID
C
INPUT
PowerCage
MTP R AV
OUTPUT
PowerCage
MTP T AV
AUDIO INPUT
L R
Y/VID
C
MTP T AV
S-video
Composite
Video
Y/VID C
CY/VID
OR
7. If power has been removed, reconnect and power on the PowerCage. The LED on
the board lights green and the new board is auto-detected.
8. Following the image at right, connect input or output
device cables to the the two BNC connectors for S-video
signals or for composite video signals.
Extron
USA - West
Headquarters
+800.63 3.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron
USA - East
+800.63 3.9876
Inside USA / Canada Only
+1.919.863.1794
+1.919.863.1797 FAX
Extron
Europe
+800.39 87.6673
Inside Europe Only
+31.33.453.4040
+31.33.453.4050 FAX
Extron
Asia
+800.7339.8766
Inside Asia Only
+65.638 3.44 00
+65.638 3.46 64 FAX
Extron
Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron
China
+400.883.1568
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FA X
Extron
Middle East
+971.4.2991800
+971.4.2991880 FAX
68-1643-50
Rev A
08 10
© 2010 Extron Electronics. All rights reserved. www.extron.com
2
PowerCage MTP T AV and MTP R AV Board Setup Guide, cont’d
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Wire color
T568A T568B
White-orange
Orange
White-green
White-blue
Green
White-brown
Brown
Blue Blue
Insert Twisted
Pair Wires
Pins:
12 34 56 78
RJ-45
Connector
PowerCage 1600
COMM
1
POWER
ALARM
2 3 14 15 16
1
PSU
2
PSU
1
FAN
2
FAN
COMM
SELECT
CONFIG
TEMP
2
1
9. Insert a 5-pole captive screw connector into the captive screw audio input or
output connector for balanced or unbalanced stereo audio input, or mono
output. Wire the connector as shown.
L R
Unbalanced Stereo Input
Balanced Stereo Input
Ring
Sleeve (s)
Tip
Sleeve
Tip
Sleeve
Tip
Tip
Ring
Do not tin the wires!
Tip
Ring
Sleeve
Tip
Ring
Tip
NO Ground Here
NO Ground Here
Sleeve
Tip
CAUTION
For unbalanced audio, connect
the sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to
the negative (-) contacts.
Unbalanced Mono Output
Balanced Mono Output
NOTE: These boards do not have a jumper to set for stereo audio output.
Audio output is always mono.
10. Either connect the output RJ-45 on the
MTP T AV to an MTP receiver using CAT 5, 5e,
or 6 cable; or connect the input RJ-45 on the
MTP R AV board with an output cable to a suitable
MTP transmitter. Terminate the cable as shown on
the right, using the same standard
(T568A or T568B) at both ends.
11. Image sharpness and gain (MTP R AV only) can be
adjusted with the two front panel rotary encoders
for optimizing the image and signal quality.
View the image and adjust the either control for the best image quality.
PowerCage Front Panel
The following PowerCage enclosure front panel features are relevant to the
installation and operation of the MTP T AV and MTP R AV boards.
NOTE: The MTP T AV and MTP R AV boards are not configurable, and the
PowerCage Comm port feature does not work with the MTP boards.
a Power LED (slots 1-16) —
This LED lights to indicate that power
is applied to the selected board.
b Temperature LED — This LED
lights if the temperature within
the PowerCage enclosure is high
(approximately 167 °F [75 °C]) and
equipment damage is imminent.
For full installation and operating details of the PowerCage, refer to the
PowerCage 1600 Enclosure User Guide available at www.extron.com.
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Extron MTP 15HD RSA User manual
-
-
Extron PowerCage MTP T AV User manual
-
-
-
Extron electronics 1600 User manual
-
-
Extron PowerCage FOX Tx VGA User manual
-
Extron electronics PowerCage FOX Tx VGA User manual
-
Extron electronics PowerCage FOX Rx AV User manual
