ProPlex PPDDSDIN14RA User guide

PPDDSDIN14RA
Brand
ProPlex
Model
PPDDSDIN14RA
Type
User guide

ProPlex PPDDSDIN14RA is a DIN rail mounted opto-splitter that provides electrical isolation and signal amplification for DMX signals. It features four isolated DMX outputs, allowing you to distribute a single DMX input signal to multiple devices without compromising signal quality or introducing ground loops. You can also daisy-chain multiple units together to create larger DMX networks. The unit is powered by a 24V DC power supply and has a rugged metal housing for durability in harsh environments.

ProPlex PPDDSDIN14RA is a DIN rail mounted opto-splitter that provides electrical isolation and signal amplification for DMX signals. It features four isolated DMX outputs, allowing you to distribute a single DMX input signal to multiple devices without compromising signal quality or introducing ground loops. You can also daisy-chain multiple units together to create larger DMX networks. The unit is powered by a 24V DC power supply and has a rugged metal housing for durability in harsh environments.

D A T A D I S T R I B U T I O N
ProPlex DIN Rail
Opto-Splitter 1x4 and 1x4 RDM
Quick Start Guide
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 2
Setup
ProPlex DIN Rail devices use a standard Phoenix MSTB screw terminal
connector in various pin configurations. Please refer to the wiring diagrams
below for correct hook up of your ProPlex DIN Rail product.
1. Connect the 24V DC power to the power input located in left top
corner. The connector should be wired as depicted in the image below.
2. Connect the DMX signal input to the DMX input in the right top corner.
The connector should be wired as depicted in the image below.
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 3
2.1 To pass DMX to another device, connect the DMX cable to the DMX Thru
port located in the right top corner of the unit. The connector should be wired
as depicted in the image below.
3. Connect the optically isolated DMX signal outputs to DMX links. The
connector should be wired as depicted in the image below.
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 4
Connection Scheme
The image below shows DMX signal “daisy-chaining” of the opto splitters via the DMX
thru.
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 5
Dimensions
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 6
Connections
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 7
LED Status Information
The Power LED has two states: ON and OFF.
• ON: Unit is receiving power
• OFF: Unit is not receiving power
The DMX INPUT / THRU activity LED has two status colors: RED and YELLOW.
• RED: There is no active incoming DMX signal
• YELLOW: There is an active incoming DMX signal
The DMX output activity LED has two (non-RDM) or three (RDM) status
colors: YELLOW and OFF (non-RDM); YELLOW, OFF, and BLINKING RED
(RDM).
• OFF: There is no DMX outgoing signal
• YELLOW: There is an active DMX outgoing signal
• YELLOW with BLINKING RED: There is RDM activity packets on the
DMX link
Note: ProPlex DIN Rail Opto-Splitters are a part of a lighting control signal
network. Opto-Splitters are used for standard DMX signal amplification,
isolation and splitting to multiple DMX outputs. Opto-Splitters ensure the safety
of the equipment on either side of the Opto-Splitter. Should there be an
electrical failure in a piece of equipment on one side of the Opto-Splitter, the
attached equipment on the opposite side will not be affected. There is no
isolation however between the IN and THRU connections.
RDM Opto-Splitters provide all of the same protection as standard Opto-
Splitters with the addition of RDM protocol support.
ProPlex Opto-Splitter DIN Quick Start Guide, v1.2 14 June 2021 8
CONTACT INFORMATION
LOS ANGELES HEADQUARTERS
527 Park Avenue | San Fernando, CA 91340, USA
Tel: +1 818.899.8818 | Fax: +1 818.899.8813
sales@tmb.com
TMB 24/7 TECH SUPPORT
US/Canada: +1.818.794.1286
Toll Free: 1.877.862.3833 (1.877.TMB.DUDE)
UK: +44 (0)20.8574.9739
Toll Free: 0800.652.5418
techsupport@tmb.com
LOS ANGELES +1 818.899.8818
LONDON +44 (0)20.8574.9700
NEW YORK +1 201.896.8600
BEIJING +86 10.8492.1587
CANADA +1 519.538.0888
A full service company providing technical
support, customer service, and follow-up.
Providing products and services for the industrial,
entertainment, installation, defense, broadcast,
research, telecommunications, and signage industries.
Servicing the global market from offices in
Los Angeles, London, New York, Toronto, and Beijing.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

ProPlex PPDDSDIN14RA User guide

PPDDSDIN14RA
Brand
ProPlex
Model
PPDDSDIN14RA
Type
User guide

ProPlex PPDDSDIN14RA is a DIN rail mounted opto-splitter that provides electrical isolation and signal amplification for DMX signals. It features four isolated DMX outputs, allowing you to distribute a single DMX input signal to multiple devices without compromising signal quality or introducing ground loops. You can also daisy-chain multiple units together to create larger DMX networks. The unit is powered by a 24V DC power supply and has a rugged metal housing for durability in harsh environments.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents