DFI CM100-C User manual

www.dﬁ .com

1

Chapter 1 Introduction

CM100-C

Mini-ITX Industrial Motherboard

User’s Manual

A25000304

www.dﬁ .com

2

Chapter 1 Introduction

Copyright

This publication contains information that is protected by copyright. No part of it may be re-

produced in any form or by any means or used to make any transformation/adaptation without

the prior written permission from the copyright holders.

This publication is provided for informational purposes only. The manufacturer makes no

representations or warranties with respect to the contents or use of this manual and specifi-

cally disclaims any express or implied warranties of merchantability or fitness for any particular

purpose. The user will assume the entire risk of the use or the results of the use of this docu-

ment. Further, the manufacturer reserves the right to revise this publication and make changes

to its contents at any time, without obligation to notify any person or entity of such revisions

or changes.

Changes after the publication’s first release will be based on the product’s revision. The website

will always provide the most updated information.

Trademarks

Product names or trademarks appearing in this manual are for identification purpose only and

are the properties of the respective owners.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-

able protection against harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encour-

aged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio TV technician for help.

Notice:

1. The changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate the equipment.

2. Shielded interface cables must be used in order to comply with the emission limits.

www.dﬁ .com

3

Chapter 1 Introduction

Copyright .............................................................................................................2

Trademarks ........................................................................................................2

FCC and DOC Statement on Class B ..................................................... 2

About this Manual ..........................................................................................4

Warranty ............................................................................................................4

Static Electricity Precautions ...................................................................... 4

Safety Measures ..............................................................................................4

About the Package .........................................................................................5

Chapter 1 - Introduction .............................................................................6

Specifications ................................................................................................6

Features ........................................................................................................7

Chapter 2 - Hardware Installation ................................................9

Board Layout ................................................................................................. 9

System Memory ............................................................................................ 9

Installing the DIMM Module ....................................................... 10

CPU ................................................................................................................ 11

Installing the CPU ....................................................................................... 11

Installing the Fan and Heat Sink.................................................................. 12

Jumper Settings ......................................................................................... 13

Clear CMOS Data ........................................................................................ 13

USB Power Select ....................................................................................... 14

PS/2 Power Select ...................................................................................... 14

COM5/ COM6 RS232/422/485 Select ........................................................... 15

COM1/ COM2 RS232 Power Select ............................................................... 15

Power-on Select.......................................................................................... 16

Rear Panel I/O Ports ................................................................................. 16

PS/2 Keyboard and PS/2 Mouse Ports .......................................................... 17

COM (Serial) Ports ...................................................................................... 17

Graphics Interface ...................................................................................... 18

RJ45 LAN Ports ........................................................................................... 18

USB Ports ................................................................................................... 19

Audio ......................................................................................................... 20

I/O Connectors ........................................................................................... 20

S/PDIF Connector ....................................................................................... 20

SATA (Serial ATA) Connectors ...................................................................... 21

Cooling Fan Connectors............................................................................... 21

Chassis Instrusion Connector ..................................................................... 22

Power Connectors ....................................................................................... 22

Standby Power LED .................................................................................... 23

Digital I/O Connectors ................................................................................ 23

Front Panel Connectors ............................................................................... 24

Expansion Slots .......................................................................................... 24

Battery ....................................................................................................... 26

Chapter 3 - BIOS Setup ............................................................... 27

Overview ..................................................................................................... 27

AMI BIOS Setup Utility ............................................................................. 28

Main .......................................................................................................... 28

Advanced ................................................................................................... 28

Chipset ...................................................................................................... 38

Boot........................................................................................................... 42

Security ...................................................................................................... 43

Save & Exit ................................................................................................ 44

Updating the BIOS .................................................................................... 45

Chapter 4 - Supported Software .......................................................... 46

Appendix A - nLite and AHCI Installation Guide ........................... 57

nLite ............................................................................................................... 57

AHCI .............................................................................................................. 61

Appendix B - Watchdog Sample Code ................................................ 63

Appendix C - System Error Message ................................................... 64

Appendix D - Troubleshooting ................................................................ 65

Appendix E - BIOS Status Code ............................................................ 67

Table of Contents

www.dﬁ .com

4

Chapter 1 Introduction

About this Manual

An electronic file of this manual is included in the CD. To view the user’s manual in the CD,

insert the CD into a CD-ROM drive. The autorun screen (Main Board Utility CD) will appear.

Click “User’s Manual” on the main menu.

Warranty

1. Warranty does not cover damages or failures that arised from misuse of the product,

inability to use the product, unauthorized replacement or alteration of components and

product specifications.

2. The warranty is void if the product has been subjected to physical abuse, improper instal-

lation, modification, accidents or unauthorized repair of the product.

3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-

stances, attempt to perform service, adjustments or repairs on the product, whether in or

out of warranty. It must be returned to the purchase point, factory or authorized service

agency for all such work.

4. We will not be liable for any indirect, special, incidental or consequencial damages to the

product that has been modified or altered.

Static Electricity Precautions

It is quite easy to inadvertently damage your PC, system board, components or devices even

before installing them in your system unit. Static electrical discharge can damage computer

components without causing any signs of physical damage. You must take extra care in han-

dling them to ensure against electrostatic build-up.

1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are

ready to install it.

2. Wear an antistatic wrist strap.

3. Do all preparation work on a static-free surface.

4. Hold the device only by its edges. Be careful not to touch any of the components, contacts

or connections.

5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con-

nectors by their ends.

Safety Measures

To avoid damage to the system:

• Use the correct AC input voltage range.

To reduce the risk of electric shock:

• Unplug the power cord before removing the system chassis cover for installa-

tion or servicing. After installation or servicing, cover the system chassis before

plugging the power cord.

Important:

Electrostatic discharge (ESD) can damage your processor, disk drive and other com-

ponents. Perform the upgrade instruction procedures described at an ESD worksta-

tion only. If such a station is not available, you can provide some ESD protection by

wearing an antistatic wrist strap and attaching it to a metal part of the system chas-

sis. If a wrist strap is unavailable, establish and maintain contact with the system

chassis throughout any procedures requiring ESD protection.

www.dﬁ .com

5

Chapter 1 Introduction

About the Package

The package contains the following items. If any of these items are missing or damaged,

please contact your dealer or sales representative for assistance.

• One CM100-C motherboard

• One Serial ATA data cable

• One I/O shield

• One DVD

• One QR (Quick Reference)

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Optional Items

• Serial ATA data cable

• Serial ATA power cable

• USB port cable

• COM port cable

• I/O shield

The board and accessories in the package may not come similar to the information listed

above. This may differ in accordance to the sales region or models in which it was sold. For

more information about the standard package in your region, please contact your dealer or

sales representative.

Before Using the System Board

Before using the system board, prepare basic system components.

If you are installing the system board in a new system, you will need at least the

following internal components.

• A CPU

• Memory module

• Storage devices such as hard disk drive, CD-ROM, etc.

You will also need external system peripherals you intend to use which will nor-

mally include at least a keyboard, a mouse and a video display monitor.

www.dﬁ .com

6

Chapter 1 Introduction

Rear Panel I/O

Ports

• 1 mini-DIN-6 port for PS/2 mouse/keyboard

• 4 USB 3.0/2.0/1.1 ports

• 2 USB 2.0/1.1 ports

• 1 DB-9 serial port

- Supports RS232 (RS232 and/or Power)

• 1 HDMI port

• 2 DVI-I ports (DVI-D signal)

• 2 RJ45 LAN ports

• Line-in/surround, Line out, and Mic-in/Center+Subwoofer jacks

I/O Connectors

• 2 connectors for 4 external USB 2.0/1.1 ports

• 5 connectors for 5 external serial ports

- 2 RS232/422/485

- 2 RS232

- 1 RS232 (RS232 and/or Power)

• 1 8-bit Digital I/O connector

• 1 front audio connector for line-out and mic-in jacks

• 4 SATA 3.0 ports

• 1 S/PDIF connector

• 1 24-pin ATX power connector

• 1 4-pin 12V power connector

• 1 chassis intrusion connector

• 2 fan connectors

• 1 front panel connector

Energy Efﬁ cient

Design

• ACPI v3.0 speciﬁ cation

• System Power Management

• Wake-On-Events include:

- Wake-On-PS/2 KB/Mouse

- Wake-On-USB KB/Mouse

- Wake-On-LAN

- RTC timer to power-on the system

• AC power failure recovery

Damage Free

Intelligence

• Monitors CPU/system temperature and overheat alarm

• Monitors VDD/VDDNB/VDDIO/1.1V/1.2V/3.3V/5V/12V voltages and failure

alarm

• Monitors CPU/system fan speed and failure alarm

• Read back capability that displays temperature, voltage and fan speed

• Watchdog timer function

- Watchdog timeout programmable via software from 1 to 255 seconds

Chapter 1 - Introduction

Specifications

Processor

• AMD

®

Embedded R-Series APUs

: R-464L Quad-core 2.3GHz, 35W

: R-460H Quad-core 1.9GHz, 35W

: R-272F Dual-core 2.7GHz, 35W

: R-268D Dual-core 2.5GHz, 35W

• PGA (FS1r2) socket

• 32nm process technology

Chipset

• AMD

®

A70M Fusion Controller Hub

System Memory

• Two 204-pin DDR3 SODIMM sockets

• Supports DDR3 (1.5V), LVDDR3 (1.35V), ULVDDR3 (1.25V) up to 1600MHz

• Supports dual channel memory interface

• Supports up to 16GB system memory

• DRAM device technologies: 1Gb, 2Gb, 4Gb and 8Gb DDR3 DRAM technologies

are supported for x8 and x16 devices, unbuffered, non-ECC

Expansion Slots

• 1 PCIe x16 slot

• 2 DFI Proprietary Extension Bus for customized expansion via a riser card

• 1 Mini PCIe slot (PCIe and USB signals)

- Supports half size Mini PCIe card

Graphics

• AMD Radeon

TM

Dual Graphics technology delivers enhanced 3D graphics

rendering perfomance

• Display ports: 1 HDMI, 2 DVI (DVI-D signal)

• DirectX 11, Hardware H.264, VC-1, MPEG-2, DivX at 1080p@60fps

Audio

• Realtek ALC886 5.1-channel High Deﬁ nition Audio

• Audio outputs: Mic-in/Center+Subwoofer, line-in/surround and line-out

• S/PDIF audio interface

LAN

• 2 Intel

®

WG82574L PCI Express Gigabit Ethernet controllers

• Integrated 10/100/1000 transceiver

• Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3ab

Serial ATA

Interface

• 4 SATA 3.0 ports with data transfer rate up to 6Gb/s

• Integrated Advanced Host Controller Interface (AHCI) controller

USB Interface

• XHCI Host Controller supports up to 4 super speed USB 3.0 ports

EEProm

(optional)

• 32~128KB

NVRam

(optional)

• 4~8MB

Trusted Platform

Module (TPM)-

optional

• Provides a Trusted PC for secure transactions

• Provides software license protection, enforcement, and password protection

BIOS

• AMI BIOS

- 32Mbit SPI BIOS

Dimensions

• Mini-ITX form factor

• 170mm (6.7") x 170mm (6.7")

Temperature

• Operating: 0

o

C to 60

o

C

• Storage: -40

o

C to 85

o

C

Humidity

• 10% to 90%

Chapter 1

www.dﬁ .com

7

Chapter 1 Introduction

Chapter 1

Features

• Watchdog Timer

The Watchdog Timer function allows your application to regularly “clear” the system at the set

time interval. If the system hangs or fails to function, it will reset at the set time interval so

that your system will continue to operate.

• DDR3

DDR3 delivers increased system bandwidth and improved performance. The advantages of

DDR3 are its higher bandwidth and its increase in performance at a lower power than DDR2.

• Graphics

The integrated AMD

®

Radeon

TM

dual graphics engine delivers an excellent blend of graphics

performance and features to meet business needs. It provides excellent video and 3D graphics

with outstanding graphics responsiveness. These enhancements deliver the performance and

compatibility needed for today’s and tomorrow’s business applications. Supports HDMI, DVI-I

for up to 2 independent displays.

• DVI

DVI (Digital Visual Interface) is a form of video interface technology made to maximize the

quality of flat panel LCD monitors and modern video graphics cards. Data is transmitted using

the TMDS (Transition Minimized Differential Signaling) protocol, providing a digital signal from

the PC’s graphics subsystem to the display.

• Serial ATA

Serial ATA is a storage interface that is compliant with SATA 1.0a specification. With speed of

up to 6Gb/s (SATA 3.0), it improves hard drive performance faster than the standard parallel

ATA whose data transfer rate is 100MB/s. The bandwidth of the SATA 3.0 will be limited by

carrier board design.

• Gigabit LAN

Two Intel

®

WG82574L PCI Express Gigabit Ethernet LAN controller supports up to 1Gbps data

transmission.

• Audio

The Realtek ALC886 audio codec provides 5.1-channel High Definition audio output.

• USB

The system board supports the new USB 3.0. It is capable of running at a maximum transmis-

sion speed of up to 5 Gbit/s (625 MB/s) and is faster than USB 2.0 (480 Mbit/s, or 60 MB/s)

and USB 1.1 (12Mb/s). USB 3.0 reduces the time required for data transmission, reduces

power consumption, and is backward compatible with USB 2.0. It is a marked improvement

in device transfer speeds between your computer and a wide range of simultaneously

accessible external Plug and Play peripherals.

Important:

The 5V_standby power source of your power supply must support ≥720mA.

• Wake-On-USB

This function allows you to use a USB keyboard or USB mouse to wake up a system from the

S3 (STR - Suspend To RAM) state.

• RTC Timer

The RTC installed on the system board allows your system to automatically power-on on the

set date and time.

• ACPI STR

The system board is designed to meet the ACPI (Advanced Configuration and Power Interface)

specification. ACPI has energy saving features that enables PCs to implement Power Manage-

ment and Plug-and-Play with operating systems that support OS Direct Power Management.

ACPI when enabled in the Power Management Setup will allow you to use the Suspend to RAM

function

.

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the

5V_standby power source of your power supply must support ≥1.5A. For 3 or more

USB ports, the 5V_standby power source of your power supply must support ≥2A.

• Wake-On-LAN

This feature allows the network to remotely wake up a Soft Power Down (Soft-Off) PC. It

is supported via the onboard LAN port or via a PCI LAN card that uses the PCI PME (Power

Management Event) signal. However, if your system is in the Suspend mode, you can power-

on the system only through an IRQ or DMA interrupt.

With the Suspend to RAM function enabled, you can power-off the system at once by pressing

the power button or selecting “Standby” when you shut down Windows® without having to

go through the sometimes tiresome process of closing files, applications and operating system.

This is because the system is capable of storing all programs and data files during the entire

operating session into RAM (Random Access Memory) when it powers-off. The operating ses-

sion will resume exactly where you left off the next time you power-on the system.

www.dﬁ .com

8

Chapter 1 Introduction

Important:

The 5V_standby power source of your power supply must support ≥720mA.

• Power Failure Recovery

When power returns after an AC power failure, you may choose to either power-on the system

manually or let the system power-on automatically.

Chapter 1

www.d.com

9

Chapter 2 Hardware Installation

Chapter 2

Chapter 2 - Hardware Installation

Board Layout

System Memory

DDR3-1

DDR3-2

Standby

Power LED

Features

• Two 204-pin DDR3 SODIMM sockets

• Supports 1066/1333/1600MHz DDR3 SDRAM

• Dual channel memory interface

• Supports maximum of 16GB system memory

Important:

Electrostatic discharge (ESD) can damage your board, processor, disk drives, add-in

boards, and other components. Perform installation procedures at an ESD workstation

only. If such a station is not available, you can provide some ESD protection by wear-

ing an antistatic wrist strap and attaching it to a metal part of the system chassis. If

a wrist strap is unavailable, establish and maintain contact with the system chassis

throughout any procedures requiring ESD protection.

Important:

When the Standby Power LED lit red, it indicates that there is power on the system

board. Power-off the PC then unplug the power cord prior to installing any devices.

Failure to do so will cause severe damage to the motherboard and components.

COM6

12

10 9

COM5

12

10 9

COM4COM3

12

10 9

12

10 9

1

Chassis intrusion

Winbond

W83627DHG

DIO

COM2

Front

Panel

COM2 RS232

Power select

(JP15)

2

1

2

5

6

12

1

11

Buzzer

1

SPI Flash BIOS

1

System Fan

Standby Power LED

Battery

SATA 0

SATA 1

SATA 2

SATA 3

2

1

USB 2-3

10

1

USB 2.0(0-3) power select(JP5)

USB 0-1

AMD

A70M

PGA FS1r2

+12V Power

1

12

13

24

COM5

RS232/422/485

select (JP11)

1

PS/2 power select(JP10)

USB 2.0

(4-5) Power

select(JP6)

1

COM1 RS232

power select(JP16)

1

2

5

6

1

USB 3.0 (0-1)

Power select (JP7)

USB 3.0 (2-3) Power select(JP8)

1

S/PDIF

Front Audio

1 2

9 10

Clear CMOS(JP1)

1

Mini PCIe

PCIe x16

DFI Proprietary

Extension Bus

USB 3.0 (0-1)

LAN 1

USB 3.0 (2-3)

LAN 2

DVI0

DVI1

KB/ MS

USB 2.0 (4-5)

HDMI

COM1

DDR3_1 SODIMM

DDR3_2 SODIMM

Intel WG82574L

2 1

56

LPC

12

10 9

2 1

56

DFI Proprietary

Extension Bus

Line-in/Surround

Line-out

Mic-in/Center+Subwoofer

12

10 9

Power-on

select (JP4)

COM6

RS232/422/485

select (JP14)

2

1

10

CPU Fan

1

COM6

12

10 9

COM5

12

10 9

COM4COM3

12

10 9

12

10 9

1

Chassis intrusion

Winbond

W83627DHG

DIO

COM2

Front

Panel

COM2 RS232

Power select

(JP15)

2

1

2

5

6

12

1

11

Buzzer

1

SPI Flash BIOS

1

System Fan

Standby Power LED

Battery

SATA 0

SATA 1

SATA 2

SATA 3

2

1

USB 2-3

10

1

USB 2.0(0-3) power select(JP5)

USB 0-1

AMD

A70M

PGA FS1r2

+12V Power

1

12

13

24

COM5

RS232/422/485

select (JP11)

1

PS/2 power select(JP10)

USB 2.0

(4-5) Power

select(JP6)

1

COM1 RS232

power select(JP16)

1

2

5

6

1

USB 3.0 (0-1)

Power select (JP7)

USB 3.0 (2-3) Power select(JP8)

1

S/PDIF

Front Audio

1 2

9 10

Clear CMOS(JP1)

1

Mini PCIe

PCIe x16

DFI Proprietary

Extension Bus

USB 3.0 (0-1)

LAN 1

USB 3.0 (2-3)

LAN 2

DVI0

DVI1

KB/ MS

USB 2.0 (4-5)

HDMI

COM1

DDR3_1 SODIMM

DDR3_2 SODIMM

Intel WG82574L

2 1

56

LPC

12

10 9

2 1

56

DFI Proprietary

Extension Bus

Line-in/Surround

Line-out

Mic-in/Center+Subwoofer

12

10 9

Power-on

select (JP4)

COM6

RS232/422/485

select (JP14)

2

1

10

CPU Fan

1

www.d.com

10

Chapter 2 Hardware Installation

Chapter 2

The system board supports the following memory interface.

Single Channel (SC)

Data will be accessed in chunks of 64 bits (8B) from the memory channels.

Dual Channel (DC)

Data will be accessed in chunks of 128 bits from the memory channels. Dual channel provides

better system performance because it doubles the data transfer rate.

Single Channel

DIMMs are on the same channel.

DIMMs in a channel can be identical or

completely different. However, we highly

recommend using identical DIMMs.

Not all slots need to be populated.

Dual Channel

DIMMs of the same memory configuration

are on different channels.

Important:

You can populate either Channel A or Channel B first.

Installing the DIMM Module

1. Make sure the PC and all other peripheral devices connected to it has been powered

down.

2. Disconnect all power cords and cables.

3. Locate the DIMM socket on the system board.

4. Push the “ejector tabs” which are at the ends of the socket to the side.

Note:

The system board used in the following illustrations may not resemble the actual

board. These illustrations are for reference only.

Ejector tab

5. Note how the module is keyed to the socket.

Key

Notch

www.d.com

11

Chapter 2 Hardware Installation

Chapter 2

7. Seat the module vertically, pressing it down firmly until it is completely seated in the socket.

The ejector tabs at the ends of the socket will automatically snap into the locked position to

hold the module in place.

6. Grasping the module by its edges, position the module above the socket with the “notch” in

the module aligned with the “key” on the socket. The keying mechanism ensures the

module can be plugged into the socket in only one way.

CPU

Overview

The system board is equipped with a surface mount rPGA 988B CPU socket.

Installing the CPU

1. Make sure the PC and all other peripheral devices connected to it has been powered down.

2. Disconnect all power cords and cables.

3. Locate the FS1r2 (722-pin lidless

micro PGA) socket on the board.

4. Make sure the screw is in its

unlock position. If it’s not, use a

screwdriver to turn the screw to

its unlock position.

Screw in unlocked

position

Note:

The system board used in the following illustrations may not resemble the actual

board. These illustrations are for reference only.

www.d.com

12

Chapter 2 Hardware Installation

Chapter 2

Installing the Fan and Heat Sink

The CPU must be kept cool by using a CPU fan with heat sink. Without sufficient air circula-

tion across the CPU and heat sink, the CPU will overheat damaging both the CPU and system

board.

1. On the solder side of the board, match the retention module base to the mounting holes

around the CPU socket.

Retention module base

2. Turn to the component side of the board making sure the retention module base is posi-

tioned and fitted properly under the board.

3. Apply a thin layer of thermal paste on top of the CPU. Do not spread the paste all over

the surface. When you later place the heat sink on top, the compound will disperse evenly.

Note:

• Useonlycertifiedfanandheatsink.

• Yourfanandheatsinkpackageusuallycontainsthefanandheatsinkassembly,

and an installation guide. If the installation procedure in the installation guide dif-

fers from the one in this section, please follow the installation guide in the package.

5. Position the CPU above the socket.

The gold triangular mark on the

CPU must align with pin 1 of the

CPU socket.

Pin 1

Gold triangular mark

6. Insert the CPU into the socket until it is seated in place. The CPU will fit in only one

orientation and can easily be inserted without exerting any force. Use a screwdriver to turn

the screw to its lock position.

Screw in locked

position

Important:

Handle the CPU by its edges and avoid touching the pins.

Important:

Do not force the CPU into the socket. Forcing the CPU into the socket may bend the

pins and damage the CPU.

www.d.com

13

Chapter 2 Hardware Installation

Chapter 2

Jumper Settings

Clear CMOS Data

If you encounter the following,

a) CMOS data becomes corrupted.

b) You forgot the supervisor or user password.

you can reconfigure the system with the default values stored in the ROM BIOS.

To load the default values stored in the ROM BIOS, please follow the steps below.

1. Power-off the system and unplug the power cord.

2. Set JP1 pins 2 and 3 to On. Wait for a few seconds and set JP1 back to its default setting,

pins 1 and 2 On.

3. Now plug the power cord and power-on the system.

JP1

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

31 2

5. Connect the CPU fan’s cable connector to the CPU fan connector on the system board.

Mounting

screw

4. Place the fan / heat sink assembly on top of the CPU. The 4 screws around the heat sink

must match the screw holes of the retention module base. We strongly recommend using

this type of fan / heat sink assembly because it provides adequate cooling to the compo-

nents of the system board.

Turn each Phillips head screw half way down first to initially stabilize the heat sink onto

the board, then finally tighten each screw.

CPU fan cable

Important:

Do not turn the first screw all the way down followed by the next and so on. This is

to avoid imbalance which might cause cracks or fractures to the CPU and/or heat sink

assembly.

www.d.com

14

Chapter 2 Hardware Installation

Chapter 2

JP5 (for USB2.0 0-3), JP6 (for USB2.0 4-5), JP7 (for USB3.0 0-1) and JP8 (for USB3.0 2-3) are

used to select the power of the USB ports. Selecting +5V_standby will allow you to use a USB

device to wake up the system.

USB Power Select

USB 3.0

0-1 (JP7)

USB 3.0

2-3 (JP8)

2-3 On:

+5V_standby

1-2 On: +5V

(default)

1

3

2

1

3

2

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the

+5V_standbypowersourceofyourpowersupplymustsupport≥1.5A.For3ormore

USBports,the+5V_standbypowersourceofyourpowersupplymustsupport≥2A.

PS/2 Power Select

JP10

JP10 is used to select the power of the PS/2 keyboard/mouse port. Selecting 5V_standby will

allow you to use the PS/2 keyboard or PS/2 mouse to wake up the system.

BIOS Setting

Configure the PS/2 keyboard/mouse wake up function in the Power Management Setup

submenu of the BIOS. Refer to chapter 3 for more information.

Important:

The5VSBpowersourceofyourpowersupplymustsupport≥720mA.

USB 2.0

4-5 (JP6)

USB 2.0

0-3 (JP5)

2-3 On:

+5V_standby

1-2 On: +5V

(default)

1

3

2

1

3

2

2-3 On:

+5V_standby

1-2 On: +5V

(default)

1

3

2

1

3

2

2-3 On:

+5V_standby

1-2 On: +5V

(default)

1

3

2

1

3

2

2-3 On:

+5V_standby

1-2 On: +5V

(default)

1

3

2

1

3

2

www.d.com

15

Chapter 2 Hardware Installation

Chapter 2

COM5/COM6 RS232/RS422/RS485 Select

JP11 (for COM5) and JP14 (for COM6) are used to configure the COM ports to RS232, RS422

(Full Duplex) or RS485.

The pin function of the COM ports will vary according to the jumper’s setting.

JP11/JP14

5-6 On: RS485

6

42

531

JP14

RS232

RS422

Full Duplex

RS485

COM 5/COM 6

642

531

1-2 On: RS232

(default)

3-4 On: RS422

Full Duplex

6

42

531

COM1/COM2 RS232 Power Select

JP16

JP15

1-3, 2-4 On: RS232

(default)

3-5 (+5V), 4-6 (+12V)

On: RS232 with power

1-3, 2-4 On: RS232

(default)

3-5 (+5V), 4-6 (+12V)

On: RS232 with power

2

1 3 5

4 6

1 3 5

2 4 6

1 3 5

2 4 6

1 3 5

2 4 6

JP11

DATA+DATA-

N.C.

1

3

5

7

9

2

4

6

8

N.C.

1

3

5

7

9

2

4

6

8

RXD+

RXD-

TXD+

TXD-

1

3

5

7

9

2

4

6

8

DCD-

RD

TD

DTR-

GND

DSR-

RTS-CTS-

RI-

www.dﬁ .com

16

Chapter 2 Hardware Installation

Chapter 2

Power-on Select

To power-on via power button:

1. Set JP4 pins 1 and 2 to On.

2. Set the “AC Power Loss State” field to Always Off.

The BIOS fields are in the “Advanced” submenu of the AMI BIOS utility.

To Auto power-on:

1. Set JP4 pins 1 and 2 to On.

1-2 On:

Power-on via power button

(default)

2-3 On:

Auto Power-on

JP4

3

1

2

3

1

2

Rear Panel I/O Ports

The rear panel I/O ports consist of the following:

• 1 mini-DIN-6 port for PS/2 KB/MS

• 1 COM port

• 1 HDMI port

• 2 DVI-I ports (DVI-D signal)

• 2 RJ45 LAN ports

• 4 USB 3.0 ports

• 2 USB 2.0 ports

• Line-out jack

• Line-in/Surround jack

• Mic-in/Center+Subwoofer jack

DVI-I 0

USB 3.0

Line-out

Line-in/Surround

LAN 1

COM 1

DVI-I 1

LAN 2

PS/2

KB/MS

Mic-in/Center+

Subwoofer

HDMI

USB 2.0

www.dﬁ .com

17

Chapter 2 Hardware Installation

Chapter 2

COM (Serial) Ports

COM 1

COM 1 to COM 4 are fixed at RS232. The pin function of COM 5 and COM 6 ports will vary

according to JP11/JP14’s setting. Refer to “COM5/COM6 RS232/RS422/RS485 Select” in this

chapter for more information.

The serial ports are asynchronous communication ports with 16C550A-compatible UARTs that

can be used with modems, serial printers, remote display terminals, and other serial devices.

Connecting External Serial Ports

Your COM port may come mounted on a card-edge bracket. Install the card-edge bracket to

an available slot at the rear of the system chassis then insert the serial port cable to the COM

connector. Make sure the colored stripe on the ribbon cable is aligned with pin 1 of the COM

connector.

BIOS Setting

Configure the serial ports in the Advanced menu (“W83627DHG Super IO Configuration” and

“F81217 Second Super IO Configuration” submenu) of the BIOS. Refer to chapter 3 for more

information.

COM 1: RS232

COM 2: RS232

PS/2 Keyboard and PS/2 Mouse Ports

These ports are used to connect a PS/2 mouse and a PS/2 keyboard. The PS/2 mouse port

uses IRQ12.

Wake-On-PS/2 Keyboard/Mouse

The Wake-On-PS/2 Keyboard/Mouse function allows you to use the PS/2 keyboard or PS/2

mouse to power-on the system. To use this function:

Jumper Setting

JP10 must be set to “2-3 On: +5V_standby”. Refer to “PS/2 Power Select” in this chapter for

more information.

BIOS Setting

Configure the PS/2 keyboard/mouse wake up function in the Advanced menu (“DFI Wakeup

Configuration” submenu) of the BIOS. Refer to chapter 3 for more information.

PS/2 Keyboard/Mouse

Important:

The 5VSB power source of your power supply must support ≥720mA.

COM 3/ COM4:

RS232

COM 5/ COM6:

RS232/RS422/RS485

1

2

9

DCD-

TD

GND

RTS-

RI-

RD

DTR-

DSR-

CTS-

1

2

9

DCD-

TD

GND

RTS-

RI-

RD

DTR-

DSR-

CTS-

1

2

9

DCD-

TD

GND

RTS-

RI-

RD

DTR-

DSR-

CTS-

COM 5

COM 6

COM 3

COM 4

www.dﬁ .com

18

Chapter 2 Hardware Installation

Chapter 2

HDMI

Graphics Interface

The HDMI port which carries both digital audio and video signals is used to connect a LCD

monitor or digital TV that has the HDMI port.

DVI-I 0/1

The display ports consist of the following:

• HDMI

• DVI-I port (DVI-D signal)

HDMI Port

DVI-I Port (DVI-D Signal)

The DVI-I port is used to connect an LCD monitor.

Connect the display device’s cable connector to the DVI-I port (DVI-D signal). After you plug

the cable connector into the port, gently tighten the cable screws to hold the connector in

place.

BIOS Setting

Configure the display device in the Chipset menu (“North Bridge” submenu) of the BIOS. Refer

to chapter 3 for more information.

RJ45 LAN Ports

The LAN ports allow the system board to connect to a local area network by means of a

network hub.

Driver Installation

Install the LAN drivers. Refer to chapter 4 for more information.

LAN 1

Features

• Intel

®

WG82574L PCI Express Gigabit LAN controller

LAN 2

www.dﬁ .com

19

Chapter 2 Hardware Installation

Chapter 2

USB Ports

USB allows data exchange between your computer and a wide range of simultaneously acces-

sible external Plug and Play peripherals.

The system board is equipped with four USB 3.0/2.0/1.1 ports (USB 3.0 0-3) and two USB

2.0/1.1 ports (USB 2.0 4-5). The two 10-pin connectors allow you to connect 4 additional

USB 2.0/1.1 ports (USB 2.0 0-3). The additional USB ports may be mounted on a card-edge

bracket. Install the card-edge bracket to an available slot at the rear of the system chassis and

then insert the USB port cables to a connector.

BIOS Setting

Configure the onboard USB in the Advanced menu (“USB Configuration” submenu) of the

BIOS. Refer to chapter 3 for more information.

Driver Installation

You may need to install the proper drivers in your operating system to use the USB device.

Refer to your operating system’s manual or documentation for more information.

USB 2-3

USB 0-1

USB 2

USB 3

10

VCC

-Data

+Data

GND

Key

VCC

-Data

+Data

GND

N. C.

9

1

2

USB 2.0

USB 3.0

USB 1

USB 0

Important:

If you are using the Wake-On-USB Keyboard/Mouse function for 2 USB ports, the

+5V_standby power source of your power supply must support ≥1.5A. For 3 or more

USB ports, the +5V_standby power source of your power supply must support ≥2A.

Wake-On-USB Keyboard/Mouse

The Wake-On-USB Keyboard/Mouse function allows you to use a USB keyboard or USB mouse

to wake up a system from the S3 (STR - Suspend To RAM) state. To use this function:

• Jumper Setting

JP5, JP6, JP7 and JP8 must be set to “2-3 On: +5V_standby”. Refer to “USB Power Select” in

this chapter for more information.

USB 2.0

USB 5

USB 4

www.dﬁ .com

20

Chapter 2 Hardware Installation

Chapter 2

S/PDIF Connector

The S/PDIF connector is used to connect an external S/PDIF port. Your S/PDIF port may be

mounted on a card-edge bracket. Install the card-edge bracket to an available slot at the rear

of the system chassis then connect the audio cable to the S/PDIF connector. Make sure pin 1

of the audio cable is aligned with pin 1 of the S/PDIF connector.

15

+5V

Key

SPDIF out

Ground

SPDIF in

I/O Connectors

Audio

Rear Audio

The system board is equipped with 3 audio jacks. A jack is a one-hole connecting interface for

inserting a plug.

• Mic-in Jack (Pink)

This jack is used to connect an external microphone.

• Line-in Jack (Light Blue)

This jack is used to connect any audio devices such as Hi-fi set, CD player, tape player,

AM/FM radio tuner, synthesizer, etc.

• Line-out Jack (Lime)

This jack is used to connect a headphone or external speakers.

Front Audio

The front audio connector allows you to connect to the second line-out and mic-in jacks that

are at the front panel of your system.

BIOS Setting

Configure the onboard audio in the Chipset menu (“South Bridge” submenu) of the BIOS.

Refer to chapter 3 for more information.

Driver Installation

Install the audio driver. Refer to chapter 4 for more information.

Mic-in

Line-out

Line-in

Rear audio

Front

audio

1

Mic2-L

Line2-R

Front_IO_Sense

GND

Presence Signal

Key

2

10

Mic2-JD

Line2-JD

9

Mic2-R

Line2-L

Page is loading ...

DFI CM100-C User manual

DFI CM100-C User manual

Related papers

Other documents