EverFocus EPARA16D3R 2TB User manual

Instruction Manual

P

A

R

A

G

O

N

S

e

r

i

e

s

D

V

R

EVERFOCUS ELECTRONICS CORPORATION

PARAGONSeries DVR

InstructionManual

 2009 EverFocus Electronics Corp

www.everfocus.com

any means without written permission of the Everfocus Electronics Corporation.

Release Date: July 2009

QuickTime is a registered trademark of the Apple Computer, Inc.

Windows is a registered trademark of the Microsoft Corporation.

Linksys is a registered trademark of the Linksys Corporation.

D-Link is a registered trademark of the D-Link Corporation.

DynDNS is a registered trademark of the DynDNS.org Corporation.

Other product and company names mentioned herein may be the trademarks of their respective owners.

ii

Safety Precautions

• To avoid any damage, please consider the following safety warnings:

• Never place the recorder near to heaters, furnaces, other heat sources or under direct solar irradiation.

• Operate the device only in locations providing the tolerable operating temperature range

0°C~40°C/32°F ~ +104°F.

• Make sure that the device‘s ventilation slots are not covered or sheeted.

• For cleaning, make sure the device is plugged off and only use a damp cloth without acid detergent.

• Install the device only in dry and dustproof surroundings. Protect the device against any liquid‘s

penetration.

• Avoid the penetration of any artifacts, e.g. through ventilation slots.

• Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or

covers. There are no user-serviceable parts inside. Contact qualified service personnel for maintenance.

Handle the appliance with care. Do not strike or shake, as this may damage the appliance.

• Do not operate appliance with other than specified power supplies. The input power source of the power

supply is 100 ~ 240 VAC.

• Avoid any affection of the device through vibrations or mechanical shock at the recorder‘s installation

location.

• Avoid to power off DVR during playback or recording operation.

ATTENTION! This is a class A product which may cause radio interference in a domestic environment; in

this case, the user may be urged to take adequate measures.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures :

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the users’ authority to operate this equipment.

iii

This Product is RoHS compliant.

WEEE

The information in this manual was current upon publication. The manufacturer reserves the right to revise and improve his products.

Therefore, all specifications are subject to change without prior notice. Misprints reserved.

Please read this manual carefully before installing and using this unit. Be sure to keep it handy for later reference.

iv

TABLE OF CONTENTS

1 PRODUCT OVERVIEW..................................................................................................... 1

1.1 FEATURES....................................................................................................................... 1

1.2 PACKAGECONTENTS................................................................................................... 2

1.3 SPECIFICATIONS ...........................................................................................................3

1.4 FRONTPANEL ................................................................................................................ 6

1.5 REAR PANEL................................................................................................................... 9

2 INSTALLATION................................................................................................................ 11

2.1 VIDEO INPUTS/OUTPUTS INSTALLATION............................................................. 11

2.2 AUDIO INSTALLATION .............................................................................................. 13

2.3 ALARM / CONTROLCONTACTS INSTALLATION .................................................14

2.3.1 Alarm Input Contacts ........................................................................................................................... 14

2.3.2 Control Input Contact........................................................................................................................... 14

2.3.3 Alarm Output Relay.............................................................................................................................. 15

2.4 RS-485 KEYBOARD / PTZ INSTALLATION......................................................................... 15

2.4.1 General RS-485 bus installation........................................................................................................... 16

2.4.2 RS-485 pin assignment ......................................................................................................................... 17

2.4.3 EKB-500 connection with network patch cable.................................................................................... 17

2.4.4 EKB-500 connection to several DVRs.................................................................................................. 17

2.4.5 Speed Dome Installation....................................................................................................................... 18

2.5 RS-232 CONNECTION....................................................................................................... 18

2.6 USB-MOUSE INSTALLATION ............................................................................................ 18

2.7 NETWORKCONNECTION .......................................................................................... 19

2.7.1 Direct PC Connection through Crossover Network Cable................................................................... 19

2.7.2 Network Connection through Patch Cable........................................................................................... 19

2.8 FINAL INSTALL PROCESS.......................................................................................... 20

3 MOUSE AND FRONT PANEL OPERATION ...............................................................21

3.1 GENERAL USB MOUSE OPERATION....................................................................... 21

3.1.1 How to select a channel / Enable audio ............................................................................................... 21

3.1.2 OSD Root Menu.................................................................................................................................... 21

3.1.3 Operation in Configuration Menu........................................................................................................ 22

3.1.4 Component Options.............................................................................................................................. 22

3.2 GENERAL FRONT PANEL OPERATION................................................................... 24

3.2.1 Front Panel Key Review....................................................................................................................... 24

3.2.2 How to select a channel / Enable audio ............................................................................................... 24

3.2.3 OSD Root Menu.................................................................................................................................... 24

3.2.4 Operation in Configuration Menu........................................................................................................ 24

3.2.5 Component Options.............................................................................................................................. 25

4 GENERAL DVR OPERATIONS...................................................................................... 27

4.1 RECORD......................................................................................................................... 27

v

4.2 LOGIN............................................................................................................................. 27

4.3 SELECT CAMERA OPERATION................................................................................. 28

4.4 PLAYBACK....................................................................................................................28

4.5 PTZ.................................................................................................................................. 30

4.5.1 General PTZ control............................................................................................................................. 30

4.5.2 Express control PTZ............................................................................................................................. 31

4.6 LAYOUT......................................................................................................................... 32

4.6.1 Bring to full screen mode...................................................................................................................... 32

4.7 CHANNELSWITCHING............................................................................................... 33

4.8 DISPLAY........................................................................................................................33

4.9 SEQUENCE....................................................................................................................34

4.10 MONITOR.................................................................................................................... 34

4.11 ZOOM........................................................................................................................... 34

4.12 SEARCH.......................................................................................................................35

4.12.1 Time Search.......................................................................................................................................... 36

4.12.2 Event Search......................................................................................................................................... 36

4.12.3 Motion Search ...................................................................................................................................... 38

4.13 COPY............................................................................................................................ 39

4.14 LOGOUT......................................................................................................................40

5 DVR CONFIGURATION.................................................................................................. 41

5.1 CONFIGURATION MENU............................................................................................41

5.2 EXPRESS........................................................................................................................41

5.3 CAMERA SETTING ...................................................................................................... 43

5.3.1 Basic Setting......................................................................................................................................... 44

5.3.2 Video Adjust ......................................................................................................................................... 45

5.3.3 Motion .................................................................................................................................................. 46

5.3.4 Video Loss ............................................................................................................................................ 49

5.4 RECORD & PLAY SETTING........................................................................................50

5.4.1 Record .................................................................................................................................................. 50

5.4.2 Built-in Cal........................................................................................................................................... 51

5.4.3 Play....................................................................................................................................................... 52

5.5 ALARM & EVENT SETTING.......................................................................................53

5.5.1 Alarm.................................................................................................................................................... 53

5.5.2 Event..................................................................................................................................................... 55

5.6 SCHEDULE SETTING................................................................................................... 64

5.6.1 Express Setup ....................................................................................................................................... 64

5.6.2 Holidays................................................................................................................................................ 65

5.6.3 Schedule................................................................................................................................................ 66

5.7 NETWORK SETTING.................................................................................................... 70

5.7.1 LAN....................................................................................................................................................... 70

5.7.2 EMAIL.................................................................................................................................................. 71

5.7.3 DDNS ................................................................................................................................................... 71

5.7.4 Alarm Server......................................................................................................................................... 73

5.8 DISPLAY SETTING....................................................................................................... 74

5.8.1 Monitor OSD........................................................................................................................................ 74

5.8.2 Main M/T SEQ...................................................................................................................................... 75

5.8.3 Call M/T SEQ....................................................................................................................................... 75

vi

5.9 DISK SETTING.............................................................................................................. 76

5.9.1 Disk....................................................................................................................................................... 76

5.9.2 Lock/Format......................................................................................................................................... 77

5.10 SYSTEM SETTING..................................................................................................... 78

5.10.1 Date/Time............................................................................................................................................. 78

5.10.2 Daylight Saving.................................................................................................................................... 79

5.10.3 User...................................................................................................................................................... 80

5.10.4 I/O Control........................................................................................................................................... 82

5.10.5 Misc...................................................................................................................................................... 83

5.11 INFORMATION SETTING......................................................................................... 84

5.11.1 System................................................................................................................................................... 84

5.11.2 Log........................................................................................................................................................ 85

6 NETWORKING OVERVIEW..........................................................................................87

6.1 INTRODUCTION TO TCP/IP............................................................................................... 87

6.2 SUBNET MASKS................................................................................................................ 87

6.3 GATEWAY ADDRESS......................................................................................................... 87

6.4 VIRTUAL PORTS................................................................................................................88

6.5 PRE-INSTALLATION ..........................................................................................................88

6.6 WHAT IS YOUR NETWORK SETUP?.................................................................................... 89

6.7 SIMPLE ONE TO ONE CONNECTION................................................................................... 90

6.8 DIRECT HIGH SPEED MODEM CONNECTION ..................................................................... 95

6.9 ROUTER OR LAN CONNECTION........................................................................................97

7 REMOTE OPERATION FROM BROWSER...............................................................100

7.1 CONNECTING TO PARAGON...................................................................................100

7.2 BROWSER SECURITY SETTING .................................................................................. 101

7.2.1 Installing ActiveX controls ................................................................................................................. 101

7.2.2 Enabling ActiveX Controls................................................................................................................. 103

7.3 REMOTE LIVE VIEW................................................................................................. 106

7.4 REMOTE PTZ CONTROL...........................................................................................107

7.5 REMOTE PLAYBACK................................................................................................109

8 EVERFOCUS DDNS SETUP.......................................................................................... 110

9 LINKSYS & D-LINK PORT FORWARDING .............................................................111

9.1 LINKSYS PORT FORWARDING............................................................................... 111

9.2 D-LINK PORT FORWARDING.................................................................................. 113

10 TROUBLESHOOTING ................................................................................................ 116

APPENDIX A: TIMING OF ALARM MODES....................................................................117

1

1 PRODUCT OVERVIEW

The latest EverFocus digital video recorder generation is based on MPEG-4 compression technology,

resulting in enhanced recording capacity and improved network image transmission speed with high image

quality. Comprehensive features and extended event recording settings enable the almost universal

application of this DVR series. The Paragon Series DVR comes with multiple control inputs. These inputs

include mouse control, front panel control, IR remote control and EverFocus keyboard (EKB500) control.

Mouse control is supported with the simple Graphical User Interface (GUI), offering experienced PC users

the similarity of interactive command of a computer-controlled device. With the GUI, users can command

specific actions on the Paragon Series DVR through graphical icons and visual indicators, optimized for

express operations. Simply point, click and drag the playback bar on the screen to search through recorded

information in any time slot. Setup and copy in seconds with a simple “point and click” on the command

icons. Hop on the Express Lane! All GUI functions can be operated via front panel, IR remote and keyboard

as well.

1.1 FEATURES

 Pentaplex Operation (Simultaneous live, recording, playback, archiving and remote viewing)

 User friendly GUI with graphical icons and visual indicators

 Multiple Control Inputs: mouse/front panel/remote control

 Free EverFocus DDNS Service

 Built-in DVR calculator for fast recording estimation

 Express Setup: Located in menu option for quick & easy installation

 Express Copy: Record video instantly while playing back (USB)

 Express Playback: Simply point, click and drag the playback bar to view previous recordings

 Express Search: Use intuitive playback bar with a simple drag & drop operation

 Remote configuration support from built-in web interface

 Gigabit Ethernet interface for remote network viewing and controlling

 Real-time live display for all cameras

 On-screen PTZ control via mouse or front panel

 Support EKB500 keyboard control

Chapter

1

2

 Audio recording capabilities*

 2 Hot Swappable HDD or 4 internal HDD

 Built-in DVD burner*

 Support eSATA

 2 USB 2.0 ports (located on front panel) for video archive and mouse usage

 Multi-language support

 Simultaneous VGA, composite and S-Video output

 Watermark capabilities to identify intentional modifications of recorded data

 Rack mountable

*Feature not available for all models

1.2 PACKAGE CONTENTS

 HDD fixing bracket x 4 (Internal HDD model)

 HDD tray x 2 (Removable HDD model)

 DVR fixing bracket x 2

 Remote controller x 1

 Battery x 2

 Shockproof rubber x 16(Internal HDD model)

 Screws x 16(Internal HDD model)

 Expanding screws x 16(Internal HDD model)

 SATA cable(Internal HDD model x4, Removable HDD model x 2)

 Power cord x 1

 Mouse x 1

 DVR x 1

 User manual x 1

3

1.3 SPECIFICATIONS

Video Format

NTSC / PAL (auto detected by system)

Operating System

Embedded Linux

Video Input

EPARA16: 16 x 1 V

pp

FBAS, BNC, 75 Ohm

EPARA8: 8 x 1 V

pp

FBAS, BNC, 75 Ohm

Video Loop

EPARA16: 16 x 1 V

pp

FBAS, BNC, 75 Ohm

EPARA8: 8 x 1 V

pp

FBAS, BNC, 75 Ohm

Video Output

Main monitor: 1 V

pp

FBAS, BNC at 75 Ohm

1 x VGA ( res. 800x600@60 Hz), S-Video

Video Compression

MPEG-4

Video Display

Full screen, Picture In Picture (Live only), 4-channel, 9-channel, 10-

channel, 13-channel, 16-channel

Recording Resolution

NTSC: 704 x 480, 704 x 240 or 352 x 240

PAL: 704 x 576, 704 x 288 or 352 x 288

Audio*

Input:

EPARA16: 16 Line In, 1 V

pp

@ 20 KOhm (RCA)

EPARA8: 8 Line In, 1 V

pp

@ 20 KOhm (RCA)

Output:

1 x Line out 1 V

pp

@ 20 KOhm (RCA)

(* audio models only)

Alarm Input

EPARA16: 16 Inputs

EPARA8: 8 Inputs

Alarm Output

4 Alarm Outputs (N.C/COM/N.O)

Hard Disk

4 x 3.5” SATA hard disk(Internal HDD model)

2 x 3.5” SATA hard disk(Removable HDD model)

Recording Rate

NTSC

352 x 240: 480 IPS

704 x 240: 240 IPS

704 x 480: 120 IPS

PAL

352 x 288: 400 IPS

704 x 288: 200 IPS

704 x 576: 100 IPS

4

Recording Modes

Continuous, schedule, or event recording

Playback Rate

NTSC

352 x 240: 480 IPS

704 x 240: 240 IPS

704 x 480: 120 IPS

PAL

352 x 288: 400 IPS

704 x 288: 200 IPS

704 x 576: 100 IPS

Playback Search Function

By time / date; by event (alarm / motion); Smart Motion Grid Search

Motion Detection

Adjustable by channel , 22x16 sensor fields each with 10 levels

sensitivity

Video Loss Detection

Yes

Event Log

Maximum 500000 events

Event Alarm

Fan failure, hard disk failure, hard disk temperature over, hard disk full,

HD off, power loss, record stop, network loss

Setup

Graphical On-Screen-Display

Operation

Via front panel, USB optical mouse, IR remote control, or

RS-485 operation from EKB500

Real-time Clock

Internal with optional network synchronization (NTP server)

Watchdog Function

Yes

Network

10/100/1000Mbps, RJ45 connection

File Export

USB 2.0 interface

Built-in DVD+RW (D models only)

RS-232

9-pin D-Sub socket

RS-485

Terminal connector

Power Source

100 ~ 240 VAC

Power Consumption

150 W max

Dimensions

430 (W) x 410 (D) x 88 (H) mm ; 16.9” (W) x 16.2” (D) x 3.5” (H)

Weight

6.35 kg ( 14 LBS)

5

Ambient Temperature

0°C ~ 40°C ; 32°F ~ 104°F(20%~80% humidity)

Remote Control

Handheld IR remote control; RS-485 keyboard EKB-500 (optional)

6

1.4 FRONT PANEL

Your primary interaction with your new DVR will be through the Front Panel buttons and their

corresponding buttons on the included Remote Control. Take a moment to learn where the keys are as the

remainder of the manual will refer to them often.

Figure 1-1 Front Panel

1) 2 x USB-2.0 port for USB mouse, USB-Flash-Drive

2) Multiview Keys:

16x 4x 9x 13x 10x PiP

The LED will indicate the selected screen layout.

NOTE: The Multiview keys are only active in Main monitor - operation.

3) Channel keys 1~16 / 1~8 for full screen display of selected channel. The LED will

show the active channel.

4) DVD+RW: DVD+RW drive for video data export. (for D model only)

5) DISPLAY: The DISPLAY key switches titles and status messages on the Screen in 4

steps. For details please consult chapter 4.8 DISPLAY.

7

6) SEQ: Sequence key for automatic switching of a defined camera sequence

7) ZOOM: 2x electronical zoom.

For details please consult chapter 4.11 ZOOM.

NOTE: The Zoom key is only active in Full screen at Main monitor.

8/9) MONITOR: The MONITOR key switches operation between MAIN and CALL. Theactive screen will

be Main monitor when LED is in “M”and Call monitor when LED is in “1”. For more details, please refer to

Chapter 4.10 MONITOR .

10) SEARCH: The SEARCH key opens the SEARCH menu, details in chapter 4.12 SEARCH.

11) COPY: The COPY key opens the menu for video data export, details in chapter 4.13 COPY.

12) IR Receiver: Receiver for IR remote control

13) HDD1: Removable SATA HDD #1 (only for HD removable model)

14) Key lock: Lock for hard disk door (only for HD removable model)

15) HDD2: Removable SATA HDD #2 (only for HD removable model)

16) REC: RECORD key for manual start of recording / recording standby (event recording).

LED will be ON if DVR is recording or in record standby

17) STOP: STOP key for Playback and Record

18) BACK: Reverse Playback key

19) PAUSE: Image freeze in playback mode

20) PLAY: Playback key

21) ENTER: Enter Key for menu operation and alarm acknowledge Turn camera audio ON/OFF when

viewing full screen camera. For more details, please refer to Chapter 3.2.1.

22) MENU/ESC: Used to bring up Main Menu or exit from sub-Menus.

23) JOG/SHUTTLE: Shuttle (outer wheel): In playback mode, use the SHUTTLE for fast forward /fast

reverse playback.

8

Jog (inner wheel): Use Jog to scroll through and highlight individual cameras. In

PAUSE mode, use the Jog to move frame by frame. Within menu functions, use

the jog to adjust the values / parameters.

Use either Shuttle or Jogto switch between MENU parameters.

24) POWER: LED indicating power on.

25) HDD1/HDD2: LED indicatingactive Hard Drives

HDD1: Internal/Removable HDDs in DVR

HDD2: External HDDs connected by eSATA port

26) LAN: LED for network traffic

27) ALARM: LED for alarm status

9

1.5 REAR PANEL

During initial setup you will be connecting your DVR to multiple input and output devices. This is done

through the rear panel.

Figure 1-2 Rear Panel

○

1

POWER: Power socket for external power supply, 100~240VAC power source

○

2

Audio output: Audio output

○

3

Audio inputs: Audio inputs 1~16(1~8 for EPARA8)

○

4

MAIN monitor: Main monitoroutput. Live view, playback,and Main Menu display (BNC, S-Video, and

VGA outputs available)

○

5

CALL monitor: Call monitor output. Spotmonitor for full screen live display, sequence mode and alarm

camera switching (BNC only)

○

6

Video inputs: EPARA8:

VIDEO IN (1~8): BNC video inputs for 1 V

pp

Composite video signals, automatic 75

Ohm termination (high impedance switching upon loop-through output load)

EPARA16:

VIDEO IN (1~16): BNC video inputs for 1 V

pp

Composite video signals, automatic 75

Ohm termination (high impedance switching upon loop-through output load)

○

1

○

2

○

3

○

4

○

5

gdg

○

6

○

7

○

8

○

9

○

10

○

11

○

12

10

○

7

Alarm inputs: 8 (EPARA8) or 16 (EPARA16) dry contact alarm inputs, programmable NO or NC in

alarm menu.

○

8

Alarm outputs: 4 NO/NCdry contact alarm outputs.

○

9

LAN: RJ45 network socket

○

10

RS232 socket: 9-pin D-Sub control input for RS-232

○

11

RS485 socket: For remote control via RS-485 keyboards and telemetry control

○

12

eSATA port: Used for external SATA HDD device

11

2 INSTALLATION

2.1 VIDEO INPUTS/OUTPUTS INSTALLATION

Cameras have to be connected using 75 Ohm video cable (e.g. RG-59, RG-12) and suitable BNC plugs.

Due to inappropriate absorbability, 50 Ohm coax cable (e.g. RG58), antenna cable and further types of

coax cable are not suitable.

Chapter

2

12

All connected video sources must provide a 1 V

pp

NTSC/EIA or PAL/CCIR standard video signal

(depending on DVR version).

When interconnecting transmission lines (twisted pair, fiber optics, radio) to the video inputs, make sure all

receivers are accurately calibrated.

The Main monitor can be connected to BNC, Composite, or VGA monitor output.

NOTE: VGA monitor must support 800x600@60Hz resolution.

For local DVR operation, Main monitor connection is required. Call monitor connection is optional.

13

2.2 AUDIO INSTALLATION

The PARAGON DVR provides 16/8 audio inputs and 1 audio output.

The inputs are designed for max. 1 V

pp

@ 20 KOhm input.

The installation has to be effected with audio coax cable and RCA plugs.

The output provides a max. 1 V

pp

@ 20 KOhm output line audio signal and may be connected to e.g. a

monitor‘s audio input. The direct connection of (passive) speakers is not supported.

ATTENTION: The direct connection of a non-amplified microphone is not supported (a microphone

amplifier is required).

AUDIO RECORDING FUNCTIONALITY:

Audio recording is activated / deactivated in the RECORD menu (chapter 5.4.1) for all channels.

Audio of all channels is always recorded together with (each) video and is independent of the image

recording rate.

During playback/live, use the JOG to select camera and press ENTER to turn audio ON or OFF.

Page is loading ...

EverFocus EPARA16D3R 2TB User manual

Related papers

Other documents