Supermicro A+ Server 4040C-TR, Beige User manual

Brand: Supermicro

Model: A+ Server 4040C-TR, Beige

Category: Server barebones

Type: User manual

This manual is also suitable for

A+ Server 4040C-TRB, Black

AS 4040C-TR

AS 4040C-8R

USER’S MANUAL

1.0

The information in this User’s Manual has been carefully reviewed and is believed to be accurate.

The vendor assumes no responsibility for any inaccuracies that may be contained in this document,

makes no commitment to update or to keep current the information in this manual, or to notify any

person or organization of the updates.

The manufacturer reserves the right to make changes to the product described in this manual at

any time and without notice. This product, including software, if any, and documentation may not,

in whole or in part, be copied, photocopied, reproduced, translated or reduced to any medium or

machine without prior written consent.

IN NO EVENT WILL THE MANUFACTURER BE LIABLE FOR DIRECT, INDIRECT, SPECIAL,

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO

USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGES. IN PARTICULAR, THE VENDOR SHALL NOT HAVE LIABILITY FOR ANY

HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING

THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING

SUCH HARDWARE, SOFTWARE, OR DATA.

Any disputes arising between manufacturer and customer shall be governed by the laws of Santa

Clara County in the State of California, USA. The State of California, County of Santa Clara shall

be the exclusive venue for the resolution of any such disputes. The manufacturer's total liability for

all claims will not exceed the price paid for the hardware product.

Unless you request and receive written permission from the manufacturer, you may not copy any

part of this document.

Information in this document is subject to change without notice. Other products and companies

referred to herein are trademarks or registered trademarks of their respective companies or mark

holders.

Printed in the United States of America

Manual Revision 1.0

Release Date: October 19, 2006

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the AS4040C-TR/4040C-8R.

Installation and maintainance should be performed by experienced technicians

only.

The 4040C-TR/4040C-8R is a high-end tower based on the SC748TQ-R1000/

SC748S-R1000 server chassis and the H8QCE/H8QC8 serverboard, which sup-

ports four AMD Opteron™ 800 series processors and up to 32 GB of ECC registered

DDR400 or 64 GB of ECC registered DDR333/266 SDRAM memory.

Manual Organization

Chapter 1: Introduction

The ﬁ rst chapter provides a checklist of the main components included with the

server system and describes the main features of the H8QCE/H8QC8 serverboard

and the SC748TQ-R1000/SC748S-R1000 chassis, which make up the 4040C-

TR/4040C-8R.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the 4040C-TR/4040C-8R into

a rack and check out the server conﬁ guration prior to powering up the system. If

your server was ordered without processor and memory components, this chapter

will refer you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer here for details on the system interface, which includes the functions and

information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

iii

Preface

Chapter 4: System Safety

You should thoroughly familiarize yourself with this chapter for a general overview

of safety precautions that should be followed when installing and servicing the

4040C-TR/4040C-8R.

Chapter 5: Advanced Serverboard Setup

Chapter 5 provides detailed information on the H8QCE/H8QC8 serverboard, in-

cluding the locations and functions of connectors, headers and jumpers. Refer

to this chapter when adding or removing processors or main memory and when

reconﬁ guring the serverboard.

Chapter 6: Advanced Chassis Setup

Refer to Chapter 6 for detailed information on the SC748TQ-R1000/SC748S-R1000

1U rackmount server chassis. You should follow the procedures given in this chapter

when installing, removing or reconﬁ guring SATA/SCSI or peripheral drives and when

replacing the system power supply units and cooling fans.

Chapter 7: BIOS

The BIOS chapter includes an introduction to BIOS and provides detailed informa-

tion on running the CMOS Setup Utility.

Appendix A: BIOS Error Beep Codes

Appendix B: BIOS POST Checkpoint Codes

Appendix C: System Speciﬁ cations

AS4040C-TR/4040C-8R User's Manual

Preface

Notes

Table of Contents

Preface

About This Manual ...................................................................................................... iii

Manual Organization ................................................................................................... iii

Chapter 1: Introduction

1-1 Overview ......................................................................................................... 1-1

1-2 Serverboard Features ..................................................................................... 1-2

1-3 Server Chassis Features ................................................................................ 1-3

Chapter 2: Server Installation

2-1 Overview ......................................................................................................... 2-1

2-2 Unpacking the System ................................................................................... 2-1

2-3 Preparing for Setup ........................................................................................ 2-1

Choosing a Setup Location .................................................................... 2-2

Rack Precautions .................................................................................... 2-2

Server Precautions ................................................................................. 2-2

Rack Mounting Considerations ............................................................... 2-3

2-4 Installing the System into a Rack ................................................................... 2-4

Identifying the Sections of the Rack Rails .............................................. 2-4

Installing the Chassis Rails ....................................................................... 2-5

Installing the Rack Rails ............................................................................ 2-6

Installing the Server into the Rack ............................................................ 2-7

2-5 Checking the Serverboard Setup ................................................................... 2-8

2-6 Checking the Drive Bay Setup ....................................................................... 2-9

Chapter 3: System Interface

3-1 Overview ......................................................................................................... 3-1

3-2 Control Panel Buttons .................................................................................... 3-1

Reset ....................................................................................................... 3-1

Power ...................................................................................................... 3-1

3-3 Control Panel LEDs ........................................................................................ 3-2

Power Fail ................................................................................................ 3-2

Overheat/Fan Fail .................................................................................. 3-2

NIC2 .......................................................................................................... 3-2

NIC1 .......................................................................................................... 3-2

HDD ........................................................................................................ 3-3

Power ...................................................................................................... 3-3

AS4040C-TR/4040C-8R User's Manual

3-4 Drive Carrier LEDs .......................................................................................... 3-3

Chapter 4: System Safety

4-1 Electrical Safety Precautions ........................................................................... 4-1

4-2 General Safety Precautions ............................................................................. 4-2

4-3 ESD Precautions ............................................................................................ 4-3

4-4 Operating Precautions ..................................................................................... 4-4

Chapter 5: Advanced Serverboard Setup

5-1 Handling the Serverboard ................................................................................ 5-1

5-2 Mounting the Serverboard into a Chassis ....................................................... 5-2

5-3 Processor and Heatsink Installation ................................................................ 5-3

5-4 Connecting Cables .......................................................................................... 5-5

Connecting Data Cables ........................................................................... 5-5

Connecting Power Cables ......................................................................... 5-5

Connecting the Control Panel ................................................................... 5-5

5-5 I/O Ports ........................................................................................................... 5-6

5-6 Installing Memory ............................................................................................. 5-7

5-7 Adding PCI Cards ............................................................................................ 5-8

5-8 Serverboard Details ......................................................................................... 5-9

H8QC8/H8QCE Layout ........................................................................... 5-9

H8QC8/H8QCE Quick Reference ......................................................... 5-10

5-9 Connector Deﬁ nitions .................................................................................... 5-11

ATX Power Connector .......................................................................... 5-11

Auxilliary 1 Power Connector ............................................................... 5-11

Auxilliary 2 Power Connector ............................................................... 5-11

Power LED ............................................................................................ 5-11

HDD LED ................................................................................................. 5-12

NIC1 LED .............................................................................................. 5-12

NIC2 LED .............................................................................................. 5-12

Overheat/Fan Fail LED ........................................................................... 5-12

Power Fail LED ....................................................................................... 5-13

Reset Button .......................................................................................... 5-13

Power Button ........................................................................................... 5-13

Universal Serial Bus Ports ...................................................................... 5-13

USB Headers ......................................................................................... 5-14

Serial Ports .............................................................................................. 5-14

Fan Headers ............................................................................................ 5-14

JLAN 1/2 (Ethernet Ports) ........................................................................ 5-14

Power LED/Keylock/Speaker .................................................................. 5-15

vii

Table of Contents

viii

ATX PS/2 Keyboard & Mouse Ports ....................................................... 5-15

Chassis Intrusion .................................................................................... 5-15

Wake-On-LAN ......................................................................................... 5-16

Wake-On-Ring ......................................................................................... 5-16

Overheat LED ........................................................................................ 5-16

3rd Power Supply Alarm Reset Header ................................................. 5-16

C Header for Power Supply ................................................................. 5-17

SMBus Header ........................................................................................ 5-17

Additional Fan Headers ......................................................................... 5-17

Compact Flash Power Headers ............................................................. 5-17

5-10 Jumper Settings ............................................................................................. 5-18

Explanation of Jumpers ........................................................................... 5-18

CMOS Clear ............................................................................................ 5-18

SCSI Controller Enable/Disable ............................................................. 5-19

SCSI Termination Enable/Disable .......................................................... 5-19

3rd Power Supply Fail Signal Enable/Disable ........................................ 5-19

Watch Dog Enable/Disable ..................................................................... 5-20

JLAN Enable/Disable .............................................................................. 5-20

VGA Enable/Disable ................................................................................ 5-20

5-11 Onboard Indicators ........................................................................................ 5-21

JLAN1/JLAN2 LEDs ................................................................................ 5-21

5-12 Floppy, IDE, Parallel Port, SCSI and SATA Drive Connections .................... 5-22

Floppy Connector .................................................................................... 5-22

IDE Connectors ....................................................................................... 5-23

Parallel Port Connector .......................................................................... 5-24

SATA Ports ............................................................................................. 5-24

SCSI Connectors ................................................................................... 5-25

5-13 Enabling SATA RAID .................................................................................... 5-26

Chapter 6: Advanced Chassis Setup

6-1 Static-Sensitive Devices .................................................................................. 6-1

6-2 Control Panel ................................................................................................... 6-3

6-3 System Fans .................................................................................................... 6-4

Fan Failure ................................................................................................ 6-4

Replacing Chassis Fans ........................................................................... 6-4

6-4 Drive Bay Installation ...................................................................................... 6-6

SCSI and SATA Drives ............................................................................. 6-6

Installing Components in the 5.25" Drive Bays ........................................ 6-8

6-5 Power Supply ................................................................................................... 6-9

AS4040C-TR/4040C-8R User's Manual

Table of Contents

Power Supply Failure ................................................................................ 6-9

Removing/Replacing the Power Supply .................................................... 6-9

Chapter 7: BIOS

7-1 Introduction ....................................................................................................... 7-1

7-2 Main Setup ........................................................................................................ 7-2

7-3 Advanced Settings Menu ................................................................................ 7-2

7-4 Boot Menu ..................................................................................................... 7-15

7-5 Security Menu ................................................................................................ 7-17

7-6 Exit Menu ....................................................................................................... 7-17

Appendices:

Appendix A: BIOS Error Beep Codes ....................................................................... A-1

Appendix B: BIOS POST Checkpoint Codes ............................................................ B-1

Appendix C: System Speciﬁ cations ......................................................................... C-1

Notes

AS4040C-TR/4040C-8R User's Manual

Chapter 1

Introduction

1-1 Overview

The AS4040C-TR/4040C-8R is a high-end quad processor server that is comprised

of two main subsystems: the SC748TQ-R1000/SC748S-R1000 1U server chassis

and the H8QCE/H8QC8 serverboard. Please refer to our web site for information

on operating systems that have been certiﬁ ed for use with the 4040C-TR/4040C-

8R.

In addition to the serverboard and chassis, various hardware components have

been included with the 4040C-TR/4040C-8R:

 One (1) ﬂ oppy drive w/ ﬂ oppy drive cable (CBL-0051L)

 Three (3) 9-cm hot-swap chassis fans (FAN-0090)

 Three (3) 8-cm exhaust fans (FAN-0081)

 Four (4) heatsink retention modules with 8 screws (BKT-0005L)

 Four (4) CPU backplates, pre-installed (BKT-0004L)

 Three (3) 5.25" dummy drive trays w/ rails (CSE-PT36)

 One (1) air shroud (CSE-PT0125)

 SATA Accessories (4040C-TR only)

One (1) SATA backplane (CSE-SAS-M35TQ)

Four (4) SATA cables (CBL-0044L)

Five (5) SATA drive carriers [CSE-PT39(B)]

 SCSI Accessories (4040C-8R only)

One (1) SCSI backplane (CSE-SCA-016)

One (1) SCSI cable (CBL-0063L)

Five (5) SCA SCSI drive carriers [CSE-PT39(B)]

 One (1) CD containing drivers and utilities

Chapter 1: Introduction

1-1

1-2

AS4040C-TR/4040C-8R User's Manual

1-2 Serverboard Features

At the heart of the 4040C-TR/4040C-8R lies the H8QCE/H8QC8, a quad proces-

sor serverboard based on the nVidia nForce Pro 2200 (CK804)/AMD8132 chipset.

Below are the main features of the H8QCE/H8QC8. (See Figure 1-1 for a block

diagram of the chipset).

Processors

The H8QCE/H8QC8 supports four 940-pin AMD Opteron 800 Series 64-bit pro-

cessors. Please refer to the serverboard description pages on our web site for a

complete listing of supported processors (www.supermicro.com/aplus/).

Memory

The H8QCE/H8QC8 has sixteen 184-pin DIMM slots (four for each CPU), which sup-

port up to 32 GB of registered ECC DDR400 SDRAM or up to 64 GB of registered

ECC DDR333/266 SDRAM. The memory is an interleaved conﬁ guration, which

requires modules of the same size and speed to be installed in pairs.

Onboard SATA (4040C-TR only)

SATA is provided with an on-chip 3 GB/sec SATA controller. The H8QCEprovides

four SATA ports.

Onboard SCSI (4040C-8R only)

Onboard SCSI is provided with an Adaptec AIC-7902W SCSI chip, which supports

dual channel, Ultra320 SCSI at a throughput of 320 MB/sec for each channel. The

H8QCE provides two LVD Ultra320 SCSI ports.

Onboard Controllers/Ports

One ﬂ oppy drive controller and one ATA/133/100 controller are provided to sup-

port up to four hard drives or ATAPI devices. The color-coded I/O ports include

one COM port (an additional COM header is located on the serverboard), a VGA

(monitor) port, two USB 2.0 ports, PS/2 mouse and keyboard ports and two G-bit

Ethernet ports.

Optional:

 One (1) rackmount kit (MCP-290-00001-00)

1-3

Chapter 1: Introduction

1-3 Server Chassis Features

The 4040C-TR/4040C-8R is a high-end, scaleable server platform. The following

is a general outline of the main features of the SC748TQ-R1000/SC748S-R1000

server chassis.

System Power

The SC748TQ-R1000/SC748S-R1000 features a redundant 1000W power supply

composed of two separate power modules. This power redundancy feature allows

you to replace a failed power supply without shutting down the system.

SATA Subsystem (4040C-TR only)

The SATA subsystem supports up to four 3 Gb/sec SATA hard drives, which are

hot-swappable. The SATA drives are connected to a SATA backplane. A RAID

controller card can be used with the backplane to provide data security.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the SATA drives.

SCSI Subsystem (4040C-8R only)

The SCSI subsystem supports up to four 80-pin SCA Ultra320 SCSI hard drives,

which are hot-swappable. Any standard 3.5" drives are supported. SCA = Single

Connection Attachment.) The SCSI drives are connected to a duale channel SCA

backplane with SAF-TE. A RAID controller card can be used with the SCA back-

plane to provide data security.

Note: The operating system you use must have RAID support to enable the hot-

swap capability of the SCSI drives.

ATI Graphics Controller

The H8QCE/H8QC8 features an integrated ATI video controller based on the Rage

XL graphics chip.

Other Features

Other onboard features that promote system health include onboard voltage moni-

tors, a chassis intrusion header, auto-switching voltage regulators, chassis and CPU

overheat sensors, virus protection and BIOS rescue.

1-4

AS4040C-TR/4040C-8R User's Manual

PCI Expansion Slots

The SC748TQ-R1000/SC748S-R1000 chassis supports the use of up to seven

standard size (full-height, full-length) expansion cards.

Front Control Panel

The control panel provides you with system monitoring and control. LEDs indicate

system power, power fail, HDD activity, network activity and overheat/fan fail. A

main power button and a system reset button are also included.

I/O Backplane

The I/O backplane on the SC748TQ-R1000/SC748S-R1000 provides seven PCI

expansion slots for standard size add-on cards, one COM port, a VGA port, two

USB 2.0 ports, PS/2 mouse and keyboard ports and two gigabit Ethernet ports.

Cooling System

The SC748TQ-R1000/SC748S-R1000 chassis has an innovative cooling design that

includes three 9-cm hot-swap chassis fans and three 8-cm exhaust fans located at

the rear of the chassis. The power supply modules also include a cooling fan. All

chassis and power supply fans operate continuously.

A setting in BIOS (see Chapter 7) is used to control the system fan speed. This

setting uses voltage control to allow fans to run at different speeds.

1-5

Chapter 1: Introduction

Figure 1-1. nVidia nForce Pro 2200/AMD 8132 Chipset:

System Block Diagram

Note: This is a general block diagram and may not exactly represent

the features on your serverboard. See the previous pages for the

actual speciﬁ cations of your serverboard.

8132

2200

(CK804 )

AMD Opteron

CPU #2

DIMM 1A

128-bit data + 16-bit ECC

DDR400/333/266

16 x 16 HT link (1 GHz)

Slot #2: PCI-X 100 MHz

Dual SCSI Channels

Gb LAN Ports (2)

SATA Ports (4)

UDMA133

USB Ports (4)

LPC I/O

FWH

Kybd/

Mouse

FDD

Parallel

Port

COM

Ports

AMD Opteron

CPU #1

AMD Opteron

CPU #3

AMD Opteron

CPU #4

DIMM 1B

DIMM 2A

DIMM 2B

DIMM 1A

DIMM 1B

DIMM 2A

DIMM 2B

16 x 16 HT link

(1 GHz )

128-bit data + 16-bit ECC

16 x 16 HT link

(1 GHz )

Slot #1: PCI-X 100 MHz

Slot #3: PCI-X 100 MHz

Slot #4: PCI-X 100 MHz

PCI-X CH A

PCI-X CH B

Slot #5: PCI-E x8

Slot #6: PCI-E x8

PCI-E

IPMI

Rage XL

Monitor

Fans

(8)

PCI-32

LPC Bus

DDR400/333/266

DIMM 1A

DIMM 1B

DIMM 2A

DIMM 2B

DIMM 1A

DIMM 1B

DIMM 2A

DIMM 2B

1-6

AS4040C-TR/4040C-8R User's Manual

Notes

Chapter 2: Server Installation

2-1

Chapter 2

Server Installation

2-1 Overview

This chapter provides a quick setup checklist to get your AS4040C-TR/4040C-8R up

and running. Following these steps in the order given should enable you to have

the system operational within a minimum amount of time. This quick setup assumes

that your system has come to you with the processors and memory preinstalled. If

your system is not already fully integrated with a serverboard, processors, system

memory etc., please turn to the chapter or section noted in each step for details

on installing speciﬁ c components. The 4040C-TR/4040C-8R may be employed

either as a tower or mounted in a rack as a 4U rackmount chassis. If using it as

a tower unit, please read the Server Precautions in the next section and then skip

ahead to Section 2-5.

2-2 Unpacking the System

You should inspect the box the system was shipped in and note if it was damaged

in any way. If the server itself shows damage you should ﬁ le a damage claim with

the carrier who delivered it.

Decide on a suitable location for the 4040C-TR/4040C-8R. It should be situated

in a clean, dust-free area that is well ventilated. Avoid areas where heat, electrical

noise and electromagnetic ﬁ elds are generated. You will also need it placed near

a grounded power outlet. Be sure to read the Rack and Server Precautions in the

next section.

2-3 Preparing for Setup

The box the system was shipped in may include two sets of rail assemblies, two

rail mounting brackets and mounting screws needed for installing the system into a

rack (optional kit). Follow the steps in the order given to complete the installation

process in a minimum amount of time. Please read this section in its entirety before

you begin the installation procedure outlined in the sections that follow.

2-2

AS4040C-TR/4040C-8R User's Manual

Choosing a Setup Location

- Leave enough clearance in front of the system to enable you to open the front

door completely (~25 inches).

- Leave approximately 30 inches of clearance in the back of the system to allow for

sufﬁ cient airﬂ ow and ease in servicing.

-This product is for installation only in a Restricted Access Location (dedicated

equipment rooms, service closets and the like).

Rack Precautions

- Ensure that the leveling jacks on the bottom of the rack are fully extended to the

ﬂ oor with the full weight of the rack resting on them.

- In single rack installation, stabilizers should be attached to the rack.

- In multiple rack installations, the racks should be coupled together.

- Always make sure the rack is stable before extending a component from the

rack.

- You should extend only one component at a time - extending two or more simul-

taneously may cause the rack to become unstable.

Server Precautions

- Review the electrical and general safety precautions in Chapter 4.

- Determine the placement of each component in the rack before you install the

rails.

- Install the heaviest server components on the bottom of the rack ﬁ rst, and then

work up.

- Use a regulating uninterruptible power supply (UPS) to protect the server from

power surges, voltage spikes and to keep your system operating in case of a power

failure.

Allow the hot plug SATA/SCSI drives and power supply units to cool before touch-

ing them.

Always keep the rack's front door and all server panels and covers closed when

not servicing to maintain proper cooling.

Warnings and Precautions!

Chapter 2: Server Installation

2-3

Rack Mounting Considerations

Ambient Operating Temperature

If installed in a closed or multi-unit rack assembly, the ambient operating tempera-

ture of the rack environment may be greater than the ambient temperature of the

room. Therefore, consideration should be given to installing the equipment in an

environment compatible with the manufacturer’s maximum rated ambient tempera-

ture (Tmra).

Reduced Airﬂ ow

Equipment should be mounted into a rack so that the amount of airﬂ ow required

for safe operation is not compromised.

Mechanical Loading

Equipment should be mounted into a rack so that a hazardous condition does not

arise due to uneven mechanical loading.

Circuit Overloading

Consideration should be given to the connection of the equipment to the power

supply circuitry and the effect that any possible overloading of circuits might have

on overcurrent protection and power supply wiring. Appropriate consideration of

equipment nameplate ratings should be used when addressing this concern.

Reliable Ground

A reliable ground must be maintained at all times. To ensure this, the rack itself

should be grounded. Particular attention should be given to power supply connec-

tions other than the direct connections to the branch circuit (i.e. the use of power

strips, etc.).

2-4

AS4040C-TR/4040C-8R User's Manual

2-4 Installing the System into a Rack

This section provides information on installing the system into a rack unit. Rack

installation requires the use of the optional rackmount kit If the system has already

been mounted into a rack or if you are using it as a tower, you can skip ahead to

Sections 2-5 and 2-6. There are a variety of rack units on the market, which may

mean the assembly procedure will differ slightly. The following is a guideline for

installing the server into a rack with the rack rails provided in the rackmount kit.

You should also refer to the installation instructions that came with the rack unit

you are using.

Identifying the Sections of the Rack Rails

The optional rackmount kit (MCP-290-00001-00) includes two rack rail assemblies.

Each of these assemblies consist of two sections: an inner ﬁ xed chassis rail that

secures to the chassis and an outer rack rail that secures directly to the rack itself.

The inner and outer rails must be detached from each other before installing.

To remove the inner chassis rail, pull it out as far as possible - you should hear a

"click" sound as a locking tab emerges from inside the rail assembly and locks the

inner rail. Depress the locking tab to pull the inner rail completely out. Do this for

both assemblies (one for each side).

Figure 2-1. Inner Fixed Chassis Rail

Page is loading ...

Supermicro A+ Server 4040C-TR, Beige User manual

Brand: Supermicro

Model: A+ Server 4040C-TR, Beige

Category: Server barebones

Type: User manual

This manual is also suitable for

A+ Server 4040C-TRB, Black

Download PDF

report

Supermicro A+ Server 4040C-TR, Beige User manual

This manual is also suitable for

Supermicro A+ Server 4040C-TR, Beige User manual

Related papers

Other documents