Atlas Sound Speaker System MLE Series User manual

Brand: Atlas Sound

Model: Speaker System MLE Series

Category: Loudspeakers

Type: User manual

This manual is also suitable for

Specifications subject to change without notice

167

TWO

1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 / FAX (800) 765-3435

AtlasSound.com

60 AND 30 WATT

EXPLOSION-PROOF LOUDSPEAKERS

HLE/MLE Series

FEATURES

• Explosion-Proof Loudspeakers for Signal and Communications Systems

• Listed by UL and CSA for Use in Hazardous/Combustible Environments (noted models)

• Available with Internally Mounted, Factory-Installed Transformer

• Choice of 60 or 30 Watt High-Intelligibility Driver in Cast Aluminum Housing

• Efficiency of Reflex-Style Projectors with Wide Angle or Circular Sound Dispersion

APPLICATIONS

Install HLE or MLE Series loudspeakers to efficiently and safely communicate in combustible

and dust-filled areas. All drivers comply with the regulations governing electrical equipment at

hazardous locations as set forth by the National Electric Code. Drivers are listed by UL and

CSA (HLE Series only). They are recommended for paging, signal and voice communication in

chemical processing, petroleum, natural resource exploration and atmospheres as listed in the

chart below.

GENERAL DESCRIPTION

Series HLE and MLE loudspeakers are explosion-proof compression driver/horn assemblies

engineered for high-efficiency voice and electronic signal communication in hazardous areas.

Drivers, which are protected within a rugged die-cast aluminum housing, are available in

60-watt (HLE Series) and 30-watt (MLE Series) power handling versions. Models with T suf

fix include a factory-installed, internally mounted transformer (Note: To meet UL requirements

transformer must be factory installed). All models are equipped with

⁄2" conduit access and an

adjustable mounting bracket.

Projector horns are available in two styles to meet dispersion requirements. Model HLE/MLE-

30 is a high-quality, polycarbonate projector that creates a 120 ° x 60 ° pattern for wide area

coverage. Model HLE/MLE-32 is a spun aluminum bell providing a 95 ° circular distribution

emphasis.

Note: – For Canadian use (Price List page 17 Text)

Drivers and projector horns are ordered and shipped separately. For performance accuracy,

specifications are listed for assembled configurations.

UNDERWRITERS' LABORATORY LISTINGS

DRIVER CLASS / GROUP FOR ATMOSPHERE CONTAINING:

HLE-1(T) Class 1 / Division 1 / Group C & D Gas Atmospheres (Including Ethyl, Ether, Gasoline Naphtha, Alcohols)

MLE-1(T)

HLE-3(T) Class 1 / Division 1 / Group B, C & D Gas Atmospheres (Including Ethyl, Ether, Gasoline Naphtha, Alcohols,

MLE-3(T) Butane, Propane) plus, Hydrogen, Gas and Vapor, (Manufactured Gas)

MODEL POWER FREQ. SOUND INTERNAL ASSEMBLY

DRIVER HORN RATING RESPONSE LEVEL* SENSITIVITY** DISPERSION IMPEDANCE XFMR SIZE

(“T” versions only)

HLE-1(T) HLE/MLE-30 60 Watts 250 Hz- 109dB -18dBm 120 ° x 60 ° 16 Ohms 60 Watt Driver & Horn

HLE-3(T) HLE/MLE-30 Cont. 12 kHz 108dB Model T-18

14"W x 6"H x 17

⁄2”D

MLE-1(T) HLE/MLE-30 30 Watts 300 Hz 107dB -21dBm 120 ° x 60 ° 8 Ohms 30 Watt (35.6 x 15.2 x

MLE-3(T) HLE/MLE-30 Cont. 14 kHz 106dB Model T-20 44.5cm)

HLE-1(T) HLE/MLE-32 60 Watts 190 Hz- 112dB -16dBm 95 ° 16 Ohms 60 Watt Driver & Horn

HLE-3(T) HLE/MLE-32 Cont. 12 kHz 111dB Model T-18 16

⁄2"Dia. x

MLE-1(T) HLE/MLE-32 30 Watts 200 Hz- 110dB -20dBm 95 ° 8 Ohms 30 Watt (42 x 54.6cm)

MLE-3(T) HLE/MLE-32 Cont. 10 kHz 110dB Model T-20

* Measured 1 Watt / 1 Meter.

** As microphone; re 10 dynes / cm2

HLE-1 Driver

HLE-1 Driver mounted to HLE/MLE-30 Horn

(order separately)

HLE-1 Driver mounted to HLE/MLE-32

Horn (order separately)

Specifications subject to change without notice

1601 JACK MCKAY BLVD. / ENNIS, TEXAS 75119 U.S.A.

TELEPHONE: (800) 876-3333 / FAX (800) 765-3435

AtlasSound.com

ARCHITECT AND ENGINEER SPECIFICATIONS

Explosion proof loudspeaker shall be UL Listed for use in specified

hazardous locations and/or combustible atmospheres as classified by

the National Electric Code.

UL approved compression driver for 60 Watt distributed application

shall be Atlas Sound Model HLE-1T or HLE-3T with internally mounted

60-watt transformer Model T-18. Transformer shall have primary

impedance taps at 2000, 1000, 500, 250, 125 and 85 with a 45 Ohm

tap for 45 Ohm line use only. Corresponding power taps for 70.7V line

use shall be 2.5, 5, 10, 20, 40 and 60. Secondary impedance shall be

4, 8 and 16 Ohms. For voice-coil circuit applications, UL Listed 60 Watt

Model HLE-1, or HLE-3 with 16 Ohm voice coil shall be specified.

UL approved compression driver for 30-watt distributed application

shall be Atlas Sound Model MLE-1T or MLE-3T with internally mounted

30 Watt transformer Model T-20. Transformer shall have primary

impedance taps at 2500, 1300, 666, 333, 167, 89 and 45 Ohms.

Corresponding power taps for 70.7V line use shall be 1.8, 3.7, 7.5, 15,

and 30. Power taps for 25V line shall be 1.89, 3.7, 7, and 15. Secondary

impedance shall be 8 Ohms. For voice-coil circuit applications, UL

Listed 30 Watt Model MLE-1, or MLE-3 with 8 Ohm voice coil shall be

specified.

Driver and transformer, where applicable, shall be mounted within a

heavy, cast aluminum housing. Voice coils shall be field-replaceable.

Projector horn shall be a reflex type with polycarbonate re-entrant

section. It shall be Atlas Sound Model HLE/MLE-30 for 120

x 60

sound

dispersion or HLE/MLE-32 for 95

sound coverage. Driver and horn

assembly shall have a frequency response of _______ with sensitivity

of _______(measured at 10 dynes / cm

). Sound pressure level shall

be a minimum of ________(measured at 1W/1M).

Atlas Sound Speaker System MLE Series User manual

Brand: Atlas Sound

Model: Speaker System MLE Series

Category: Loudspeakers

Type: User manual

This manual is also suitable for

Download PDF

report

Atlas Sound Speaker System MLE Series User manual

This manual is also suitable for

Atlas Sound Speaker System MLE Series User manual

Related papers

Other documents