ORFGEN Z29618-BS Operation and Safety Notes

Brand: ORFGEN

Model: Z29618-BS

Category: Holders

Type: Operation and Safety Notes

GB / IE GB / IE GB / IE GB / IE GB / IE GB / IE GB / IE

GB / IEGB / IEGB / IEGB / IEGB / IE

person responsible for their safety. Children

must never be allowed to play with the device.

J This product is not a toy and should be kept

out of the reach of children. Children are not

aware of the dangers associated with han-

dling electrical products.

J Do not use the article if you detect any kind

of damage.

J CAUTION! DANGER OF

EXPLOSION! Do not operate

the LED work lamp in potentially

explosive environments in which there are

inﬂam mable vapours, gases or dusts.

J The LED inspection lamp is protected against

water spray. However, the product, mains

adapter and car adapter must never be

immersed in water or other liquids. Failure to

observe this advice will create the risk of elec-

tric shock! Never hang the product near a

washbasin, pond and the like.

J Connect the LED work lamp to a properly

installed mains socket or a suitable cigarette

lighter socket only. The voltages in each case

must comply with information given in the

section “Technical data”.

J Ensure that the electrical socket is easily acces-

sible so that you can pull the plug quickly out

of the socket if necessary.

J Do not carry out any modiﬁcations or repairs

to the product yourself. The LEDs cannot and

must not be replaced.

m CAUTION! The protective surround to the

LEDs cannot be replaced. Dispose of the LED

inspection lamp if you discover cracks or

signs of fracture on the protective surround.

J Dispose of the product if the LED inspection

lamp, mains adapter or car adapter is dam-

aged.

J Never connect the LED work lamp to a power

supply socket if the LED work lamp, power

lead or socket is damaged or the LED work

lamp has been dropped.

J Ensure that the power lead cannot become

damaged by sharp edges or hot objects.

Unwind all the lead completely before use.

J Keep easily ﬂammable materials away the

product. Never hang objects above the LED

work lamp or the mains adapter and never

cover them.

J Pull the mains adapter / plug out of the mains

socket / cigarette lighter socket when you are

not using the LED work lamp or before you

clean it. Do this as well if signs of a fault

develop during use or charging, e.g. smoke,

burning smell etc., or during a storm. When

doing this, pull directly on the mains adapt-

er / plug and not on the lead.

J Protect the product against heat, cold, strong

vibrations and impacts.

J CAUTION! LED RADIATION.

Avoid damage to eyes! Never

look directly at the LED. Never use

optical appliances such as magnifying glasses

or the like to look at the LED. Protect yourself

and your environment by taking proper pre-

cautions.

J Never point the LED beam at reﬂective surfaces,

people or animals. This could result in blind-

ness or irritation of the eyes. Even weak LEDs

could result in eye damage.

J Do not attach the hook 1 to hot objects. The

dead weight of the LED work lamp might

cause the hook to deform or bend out of shape.

Before use

Charging the LED inspection

lamp

Note: You can charge the LED inspection lamp

from an ordinary domestic mains power outlet or

from the cigarette lighter socket in your vehicle.

Tip: We recommend that you charge the LED

inspection lamp from an ordinary domestic mains

power outlet to avoid draining your vehicle’s

battery.

CAUTION! Do not connect the LED inspection

lamp to the cigarette lighter socket of your vehicle

if the vehicle battery is old or degraded. Failure

to observe this advice may result in your vehicle’s

engine not starting.

Note: To use the LED inspection lamp without an

adapter, you must ﬁrst charge the integral recharge-

able batteries. It takes between 4 and 6 hours to

charge the integral batteries. The rechargeable

batteries are permanently installed in the handle

of the LED inspection lamp.

Note: Charge the LED inspection lamp for approx-

imately 12 hours before ﬁrst use.

Note: Charge the LED inspection lamp at least

once a month, if it is to remain unused for an

extended period of time.

Note: If the LED inspection lamp has not been

charged for an extended period of time (approx.

2 months), you could ﬁnd that the integral recharge-

able batteries have entered a dormant state.

Charge and discharge the LED inspection lamp a

number of times in succession to reactivate the

integral rechargeable batteries.

j Switch oﬀ the LED inspection lamp during the

charging process (set the ON / OFF switch

5 to position 0).

j Remove the rubber protection cap from the

bottom of the LED inspection lamp.

j Insert the power output connection plug of

the mains adapter 3 or the car adapter 4

into the power input connection socket 6 in

the handle of the LED inspection lamp.

Note: During charging from a cigarette lighter

socket, ensure that the plug is always completely

inserted into the cigarette lighter socket of the

vehicle. Failure to observe this advice may

result in risk of ﬁre from overheating.

j Insert the mains adapter 3 into a mains

socket or the car adapter 4 into the ciga-

LED Work Lamp

Introduction

Familiarise yourself with the product

before using it for the ﬁrst time. In addi-

tion please refer carefully to the operating

instructions below and the safety advice. Use the

product only as described and for the indicated

purpose. Keep these instructions in a safe place.

If you pass the product on to anyone else, please

ensure that you also pass on all the documentation.

Proper use

The product is intended for providing illumination

in dry indoor rooms and in outdoor environments.

If used outdoors the mains adapter must be pro-

tected from moisture and the weather. Any other

use or modiﬁcation of the product constitute

improper use and pose a risk of short circuits, ﬁre,

electric shocks and damage to the product. The

manufacturer is not liable for damage caused by

improper use. The product is not intended for

commercial use.

Description of parts and

features

1 Hook

2 Magnetic mount

3 Mains adapter

4 Car adapter (for cigarette lighter socket)

5 ON / OFF switch

6 Power input connection socket

7 Indicator LED

Technical data

Light bulb: 23 LEDs (white,

non-replaceable)

Light intensity : approx. 12,000 mcd

(millicandela)

Lamp rechargeable

batteries: 3 x AA NiMH, 1000 mAh

(not replaceable)

Charging time: approx. 4 to 6 hours

Burn time: approx. 3 hours (with fully

charged battery)

Lifespan of LEDs: approx. 20,000 hours

Protection class:

System of protection: IP44

Adapter:

Input: 230 V ~ 50 Hz

Output: 6 V , 300 mA

Model: YX-0603

Protection class:

System of protection: IP20

Cigarette lighter:

Input: 12 V

Output: 12 V , 240 mA

Scope of delivery

1 LED inspection lamp

1 Mains adapter

1 Car adapter for cigarette lighter socket

1 Magnetic mount

1 Operating instructions

Safety instructions

J WARNING! DANGER TO

LIFE AND RISK OF ACCIDENTS

FOR INFANTS AND CHILDREN!

Never leave children alone and unsupervised

with the packaging material. There is always

a risk of suﬀocation if children play with the

packaging material. Children often underesti-

mate risks. Always keep children away from

the packaging material. This product is not a

toy.

J Children or persons who lack the knowledge

or experience to use the device or whose

physical, sensory or intellectual capacities

are limited must never be allowed to use the

device without supervision or instruction by a

Z29618-BS

LED WORK LAMP

Operation and Safety Notes

6 5

GB / IE GB / IE GB / IE

GB / IEGB / IEGB / IEGB / IEGB / IEGB / IEGB / IE

Contact your local refuse disposal authority for

more details of how to dispose of your worn-out

product.

To help protect the environment,

please dispose of the product properly

when it has reached the end of its use-

ful life and not in the household waste.

Information on collection points and

their opening hours can be obtained

from your local authority.

Defective or exhausted rechargeable batteries

must be recycled in accordance with Directive

2006 / 66 / EC. Return the battery and / or the

device through the appropriate collection facilities.

Improper disposal of recharge-

able batteries can damage the

environment!

Rechargeable batteries must not be disposed of

with the household refuse. They may contain toxic

heavy metals and require to be handled as special

waste. The chemical symbols of heavy metals are:

Cd = cadmium, Hg = mercury, Pb = lead

EMC

Product Description:

LED Work Lamp

Model No.: Z29618-BS

Version: 12 / 2010

Level of information: 11 / 2010

ID No.: Z29618-BS112010-6

rette lighter socket of your vehicle.

Note: The product has an overcharging

protection system. Nevertheless, you should

disconnect the LED inspection lamp from the

mains once the charging process is complete.

Note: The indicator LED 7 illuminates red

during the charging process. When the

charging process is complete, the indicator

LED 7 illuminates green. When the indicator

LED 7 illuminates green, pull the mains

adapter 3 out of the mains socket or the car

adapter 4 out of the cigarette lighter socket.

Disconnect the adapter from the LED inspection

lamp to prevent the batteries from discharging

themselves.

j Place the rubber protection cap back on the

power input connection socket 6 before you

start to use the LED inspection lamp again.

Otherwise water could enter the power input

connection socket 6 if the LED inspection

lamp is used outdoors.

Use

m CAUTION – RISK OF ACCIDENT! If at

all possible, do not use the LED inspection lamp

in a moving vehicle. If the LED inspection lamp is

used in a vehicle, it must not be allowed to endan-

ger the safety of the driver or passengers. Always

store and secure the LED inspection lamp in such

a way that there is no risk of injury from or dam-

age to the product, even during full braking.

Note: You can secure the LED inspection lamp in

place using the hook 1 or magnetic mount 2.

Clamp the magnetic mount 2 to the LED’s pro-

tective surround. Then hold the LED inspection

lamp against a magnetic surface.

Using the LED inspection lamp

disconnected from a power

supply

j Fully charge the LED inspection lamp, as

described in the section on “Charging the

LED inspection lamp”.

j Set the ON / OFF switch 5 to position I to

switch on the LED inspection lamp.

j Set the ON / OFF switch 5 to position 0 to

switch oﬀ the LED inspection lamp.

Using the LED inspection lamp

connected to a power supply

m CAUTION! RISK OF INJURY! Position the

power lead so that it does not create a trip hazard.

m CAUTION RISK OF ACCIDENT! Do not

connect or use the LED inspection lamp if you are

in moving traﬃc, for example driving a vehicle.

The LED inspection lamp is not intended to be

used as an indoor lighting ﬁxture or a reading

lamp!

j Remove the rubber protection cap from the

power input connection socket 6.

j Insert the power output connection plug of the

mains adapter 3 or of the car adapter 4

into the power input connection socket 6 in

the handle of the LED inspection lamp.

j Insert the mains adapter 3 into a 230 V ~

mains socket or the car adapter 4 into the

cigarette lighter socket of your vehicle.

j Set the ON / OFF switch 5 to position I to

switch on the LED inspection lamp.

m CAUTION! If the LED inspection lamp is con-

nected to the mains by the mains adapter 3,

in this state it is intended exclusively for

indoor use.

j Set the ON / OFF switch 5 to position 0 to

switch oﬀ the LED inspection lamp.

Troubleshooting

Fault Possible causes and cures

functions

- Mains adapter 3 or car adapter

4 is not fully inserted.

Fault Possible causes and cures

Indicator

LED 7

does not

illuminate

When connected to a

cigarette lighter socket:

- Is the cigarette lighter socket

supplied

with power? Some

cigarette lighter sockets only

supply power with the ignition

switched on.

- Check the fuse in the vehicle.

Charging

takes a

very long

time

When connected to a

cigarette lighter socket:

- Vehicle battery too weak?

Maintenance and cleaning

The product requires no maintenance. The LEDs

cannot be replaced.

J Disconnect the product from the power supply

before you clean it.

J Never immerse the product in water or other

liquids.

J Do not use corrosive cleaning agents.

j Clean the product regularly with a dry, ﬂuﬀ-

free cloth. Use a slightly moist cloth to remove

any stubborn dirt.

Disposal

The packaging is made entirely of

recyclable materials, which you may

dispose of at local recycling facilities.

IAN 58812

Milomex Ltd.

c / o Milomex Services

Hilltop Cottage

Barton Road

Pulloxhill

Bedfordshire

MK45 5HP

ORFGEN Z29618-BS Operation and Safety Notes

Brand: ORFGEN

Model: Z29618-BS

Category: Holders

Type: Operation and Safety Notes

Download PDF

report

ORFGEN Z29618-BS Operation and Safety Notes

ORFGEN Z29618-BS Operation and Safety Notes

Other documents