King Canada 8313 User manual

Brand: King Canada

Model: 8313

Type: User manual

4.8V CORDLESS

SCREWDRIVER KIT

plusplus

performanceperformance

INSTRUCTION MANUAL

MODEL: 8313

WARRANTY INFORMATION

2-YEAR

LIMITED WARRANTY

FOR THIS 4.8V SCREWDRIVER

KING CANADA TOOLS

OFFERS A 2-YEAR LIMITED

WARRANTY FOR NON-COMMERCIAL USE.

PROOF OF PURCHASE

Please keep your dated proof of purchase for warranty and servicing purposes.

LIMITED TOOL WARRANTY

KING CANADA makes every effort to ensure that this product meets high quality

and durability standards. KING CANADA warrants to the original retail consumer a

2-year limited warranty as of the date the product was purchased at retail and that

each product is free from defects in materials. Warranty does not apply to defects

due directly or indirectly to misuse, abuse, negligence or accidents, repairs or

alterations and lack of maintenance. KING CANADA shall in no event be liable for

death, injuries to persons or property or for incidental, special or consequential

damages arising from the use of our products. To take advantage of this warranty,

the product or part must be returned for examination by the retailer. Shipping and

handling charges may apply. If a defect is found, KING CANADA will either repair

or replace the product.

PARTS DIAGRAM & PARTS LISTS

Refer to the Parts section of the King Canada web site for the most updated parts

diagram and parts list.

1. KNOW YOUR TOOL

Read and understand the owners manual and labels affixed to the tool. Learn its

application and limitations as well as its specific potential hazards.

2. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area

well lit and provide adequate surrounding work space.

3. USE RIGHT TOOL.

Don’t force the tool or the attachment to do a job for which it was not designed.

4. MAINTAIN TOOL WITH CARE.

Keep tool clean for best and safest performance. Follow instructions for operation and

changing accessories.

5. USE RECOMMENDED ACCESSORIES.

Only use recommended accessories. Follow the instructions that accompany the

accessories. The use of improper accessories may cause hazards.

6. CHECK FOR DAMAGED PARTS.

Before further use of the tool, parts that are damaged should be carefully checked to

ensure they will operate properly and perform their intended function. Check for

alignment of moving parts, breakage of parts, mounting, and any other conditions that

may affect its operation. Parts which are damaged should be properly repaired or

replaced.

Additional safety instructions for batteries and chargers

Batteries

-Never attempt to open the charger for any reason.

-Do not store in locations where the temperature may exceed 40˚C.

-Charge only at ambient temperatures between 4˚C and 40˚C.

-Charge only using the charger provided with the tool.

-Under extreme conditions, battery leakage may occur. When you notice liquid on the

battery, proceed as follows:

•Carefully wipe the liquid off using a cloth. Avoid skin contact.

• In case of skin or eye contact, follow the instructions below.

In case of skin contact, immediately rinse with water. Neutralise with a mild acid such as

lemon juice or vinegar. In case of eye contact, rinse abundantly with clean water for at least

10 minutes. Consult a physician.

Fire hazard! Avoid short-circuiting the contacts of a detached battery. Do not incinerate the

battery.

Chargers (This charger is intended for indoor use only)

-Use the charger provided with the tool only to charge the battery.

-Never attempt to charge non-rechargeable batteries.

-Have defective cords replaced immediately.

-Do not expose to water.

-Donot open the charger.

-Donot probe the charger.

GENERAL & SPECIFIC

SAFETY INSTRUCTIONS

GETTING TO KNOW YOUR

CORDLESS SCREWDRIVER

Specifications

Model ..................................................................................................................8313

Voltage ................................................................................................................4.8V

Collet size ............................................................................................................1/4”

Single speed (no load) ................................................................................200 RPM

Battery type ......................................................................................................Ni-Mh

Charger Input ............................................................................................120V/60Hz

Charger output........................................................................................................6V

Charge time ................................................................................................3-8 hours

1) Charger jack

2) Charger

3) 1/4” Collet

4) Forward/reverse switch

5) Power level indicator LED lights

6) Power level display button

7) Built-in rechargeable battery

8) DC socket

9) 27 pcs assorted driver bits

10) Bit extension

11) 2 Double-ended driver bits

CHARGING BATTERY,

OPERATION

Charging the Battery

Caution: The battery is not fully charged and must therefore be charged before the tool is

used for the first time.

1. Place tool within one meter of a 120V / 60 Hz wall receptacle.

2. Insert charger jack into DC socket on bottom of tool body.

3. Insert charger into a 120V / 60 Hz wall receptacle. The red indicator light will turn on.

4. Allow 3 to 8 hours for battery to become fully charged.

5. Disconnect from the charger from the tool and the wall receptacle after charging.

Do not use the tool while it is connected to the charger.

Operation

1. Insert bit into the bit holder as far as it will go.

2. Grasp the tool firmly with both hands, align the bit with the screw and press it firmly into

the screw.

3. Start the tool by pressing the ON/OFF switch. Hold down the top of the switch to turn

the screw in forward. Hold down the bottom of the switch to turn the screw in reverse.

4. Battery power charge display LED lights:

•Press the small power charge button located below the forward/reverse switch, on the

front part of the grip.

•If the red, yellow and green lights all illuminate, the battery is fully charged.

•If only the red and yellow lights illuminate, the battery is half-charged.

• If only the red light illuminates, the battery is low and the tool should be recharged.

Fitting and removing a screwdriver bit

•To fit a screwdriver bit, push it into the 1/4” collet until it locates.

•To remove a screwdriver bit, pull it straight from the 1/4” collet.

Fitting and removing a bit using extension bit holder

•Tofit the extension bit holder,push it into the 1/4” collet.

•To fit a bit, insert it into the extension bit holder.

•To remove a bit, pull it from the extension bit holder.

•To remove the extension bit holder, pull it straight from the 1/4” collet.

OPERATION & MAINTENANCE

screwdriver bit selection

Always select the correct screwdriver bit for the screw being used. Use the largest

possible size that will fit into the screw to avoid damaging the screw or the bit. Only use 1”

short bits together with the extension bit holder.

Maintenance

Your tool has been designed to operate over a long period of time with a minimum of

maintenance. Continuous satisfactory operation depends upon proper tool care and

regular cleaning. Your charger does not require any maintenance apart from regular

cleaning. Unplug the charger before cleaning it.

•Regularly clean the charger using a soft brush or dry cloth.

•Regularly clean your tool using a damp cloth.

•Do not use any abrasive or solvent-based cleaner.

Protecting the Environment

Should you find one day that your tool needs replacement, or if it is of no further use to

you, think of the protection of the environment.

If you want to dispose of the tool yourself, the battery must be removed as described below

and disposed of in accordance with local regulations.

Do not short-circuit the battery terminals. Do not use tools to remove the battery; only use

your fingers.

•Loosen the screws of tool and open the tool cover.

•Pull the battery out and disconnect the wires to remove it from the tool.

•Place the battery in a suitable packaging to ensure that the terminals cannot be short-

circuited.

•Take the battery to your service agent or a local recycling station. Collected batteries will

be recycled or disposed of properly.

King Canada 8313 User manual

King Canada 8313 User manual

King Canada 8313 User manual

Related papers

Other documents