King Canada 8055L is a 20V MAX Lithium-ion Cordless Impact Driver that combines power and versatility for a wide range of driving applications. Ideal for both professional and DIY enthusiasts, it features a variable speed trigger for precise control, a 1/4-inch hex quick-release chuck for easy bit changes, and an LED work light for illuminating dark workspaces. With a maximum torque of [value not provided], this impact driver delivers impressive power for driving screws, nuts, and bolts into various materials.
King Canada 8055L is a 20V MAX Lithium-ion Cordless Impact Driver that combines power and versatility for a wide range of driving applications. Ideal for both professional and DIY enthusiasts, it features a variable speed trigger for precise control, a 1/4-inch hex quick-release chuck for easy bit changes, and an LED work light for illuminating dark workspaces. With a maximum torque of [value not provided], this impact driver delivers impressive power for driving screws, nuts, and bolts into various materials.
COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
20V MAX LITHIUM-ION
CORDLESS IMPACT DRIVER
INSTRUCTION MANUAL
MODEL: 8055L
03/2017
WARRANTY INFORMATION
2-YEAR
LIMITED WARRANTY
FOR THIS 20V MAX LI-ION IMPACT
KING CANADA TOOLS
OFFERS A 2-YEAR LIMITED WARRANTY
FOR NON-COMMERCIAL USE.
PROOF OF PURCHASE
Please keep your dated proof of purchase for warranty and servicing purposes.
LIMITED TOOL WARRANTY
King Canada makes every effort to ensure that this product meets high quality and
durability standards. King Canada warrants to the original retail consumer a 2-year
limited warranty as of the date the product was purchased at retail and that each
product is free from defects in materials. Warranty does not apply to defects due
directly or indirectly to misuse, abuse, normal wear and tear, negligence or
accidents, repairs done by an unauthorized service center, alterations and lack of
maintenance. King Canada shall in no event be liable for death, injuries to persons
or property or for incidental, special or consequential damages arising from the use
of our products.
To take advantage of this limited warranty, return the product at your expense
together with your dated proof of purshase to an authorized King Canada service
center. Contact your retailer or visit our web site at www.kingcanada.com for an
updated listing of our authorized service centers. In cooperation with our authorized
serviced center, King Canada will either repair or replace the product if any part or
parts covered under this warranty which examination proves to be defective in
workmanship or material during the warranty period.
NOTE TO USER
This instruction manual is meant to serve as a guide only. Specifications and
references are subject to change without prior notice.
PARTS DIAGRAM & PARTS LISTS
Refer to the Parts section of the King Canada web site for the most updated parts
diagram and parts list.
KING CANADA INC. DORVAL, QUÉBEC, CANADA H9P 2Y4
www.kingcanada.com
1. KNOW YOUR TOOL
Read and understand the instruction manual and labels affixed to the tool. Learn its
application and limitations as well as its specific potential hazards.
2. Don’t use power tools in damp or wet locations or expose them to rain. Keep work area
well lit and provide adequate surrounding work space.
3. USE RIGHT TOOL.
Don’t force the tool or the attachment to do a job for which it was not designed.
4. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties or jewelry (rings, watch) because they could
get caught in moving parts. Non-slip footwear is recommended. Wear protective hair
covering to contain long hair. Roll up long sleeves above the elbows.
5. MAINTAIN TOOL WITH CARE.
Keep tool clean for best and safest performance. Follow instructions for operation and
changing accessories.
6. DISCONNECT TOOLS.
Before servicing, when changing accessories or attachments.
7. AVOID ACCIDENTAL STARTING.
Make sure the switch is in the ‘’OFF’’ position before connecting battery.
8. USE RECOMMENDED ACCESSORIES.
Consult the manual for recommended accessories. Follow the instructions that
accompany the accessories. The use of improper accessories may cause hazards.
9. CHECK FOR DAMAGED PARTS.
Before further use of the tool, a guard or other parts that are damaged should be
carefully checked to ensure they will operate properly and perform their intended
function. Check for alignment of moving parts, breakage of parts, mounting, and any
other conditions that may affect its operation. A guard or other parts which are damaged
should be properly repaired or replaced.
Specific Safety Instructions
1. Only use King attachments and accessories, serious injury can result if this warning is
not respected.
2. Before installing or changing an accessory, remove the battery from the tool. This
will prevent accidental starts and possible injuries.
3. Hold power tool by insulated grip surface, an accessory could contact hidden wiring,
contact with a “live” wire will make exposed metal surfaces “live” and will shock the
operator.
4. Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
stoves and refrigerators. Risk of electric shock if your body is grounded.
5. Use clamps or any other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to
loss of control.
6. Wear protective gloves and safety glasses, an accessory can become extremely hot
during operation, danger of burns!
7. Do not use the tool if switch does not turn it on or off. Any tool that cannot be controlled
with the switch is dangerous and must be repaired.
GENERAL & SPECIFIC
SAFETY INSTRUCTIONS
LITHIUM-ION BATTERY &
CHARGER INFORMATION
WARNING: The warnings, cautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be understood
by the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operator.
King canada offers a variety of 20V max Lithium-ion Power Tools which can all use the
same battery and battery charger. The obvious advantage is not having to purchase
separate batteries and chargers for each tool. (Battery and charger sold separately).
Available batteries and charger for this 20V max Li-ion Reciprocating Saw:
• 1.5 Ah 20V max Lithium-ion battery (Model K-020LBT)
• 3.0 Ah 20V max Lithium-ion battery (Model K-023LBT-3)
• 20V max Lithium-ion battery charger (Model K-020LCG)
Charging any other battery may damage the charger and possibly cause serious injury.
Battery and Charger Safety Precautions
1) Do not store or carry battery in a way which metal objects could contact the exposed
metal end of the battery. The battery could short-circuit causing a fire, personal injury
and damage to the battery.
2) Never attempt to open the battery for any reason. If battery housing has cracked,
discontinue use immediately and do not try to recharge it. Dispose of battery.
3) Never charge a wet battery or a battery that shows signs of corrosion.
4) Do not use an extension cord with the charger, plug charger directly into a 120V AC
receptacle.
5) Do not use charger if power cord is damaged, replace damaged cord or charger.
6) Do not charge battery when work area or the battery temperature is or below 0
0
C or
above 45
0
C.
7) Unplug charger when not in use.
8) It is important to recycle or dispose of battery properly at your nearest battery
recycling location.
9) The contents of the battery is slightly acidic, do not incinerate the battery, it can
explode in a fire.
10) A small leakage from the battery may occur under extreme usage, charging or
temperature conditions. This does not indicate a battery failure. However, if the battery
housing is cracked and leakage gets on your skin, follow these steps;
-Wash with soap immediately.
-Neutralize area with mild acid such as vinegar or lemon juice.
-If leakage gets into your eyes, flush with clean water for a minimum of 10 minutes, then
seek medical attention.
Lithium-ion Battery
Lithium-ion batteries do not have a memory and do not require to be completely
discharged periodically. After use, charge battery so that it is fully charged for the next time
you use this tool. A fully charged battery will only loose about 2% of its charge per month
during storage.
GETTING TO KNOW YOUR TOOL
SPECIFICATIONS
Model ........................................................................................................................8055L
Voltage ................................................................................................................20V MAX
Quick release chuck ..........................................................................................1/4” (hex.)
Speed range ..................................................................................................0-2000 RPM
Impacts per minute ..................................................................................................0-3300
Torque ..............................................................................................................1,350 in/lbs
1. 1/4” hex. drive quick release chuck
2. LED work light
3. Variable speed trigger
4. Forward/reverse switch
5. 20V MAX Li-ion cordless impact driver
Not shown:
• Battery power level indicator
• Bit holder
• 4 nut drivers with 1/4” hex. shank,
6 screwdriver bits (Robertson #1 & #2,
Phillips #1 & #2, 5mm & 6mm flat),
bit extension
Figure 1
OPERATION
Using your 20V MAX Lithium-ion cordless impact driver
Important Note: This Impact Driver does not come with a
battery or charger, if you already own a 20V max Li-ion cord-
less tool you may use its battery (K-020LBT) and charger (K-
020LCG) as they are interchangeable. If not, it will be nec-
essary to purchase a battery and charger.
WARNING: Do not install battery until the accessory is
installed securely to the tool. Wear protective gloves and
safety glasses, an accessory can become extremely hot dur-
ing operation, danger of burns!
Charging the battery/battery level indicator
20V max Li-ion batteries come with a battery power level
indicator (A) Fig.2, press the button (B) to see the charge
level. If the battery level is low charge the battery. To charge
the battery (C) Fig.2, plug charger (D) power cord into a
120V AC receptacle (do not use extension cord). The green
LED (E) will flash to indicate power to the charger. Align the
grooves the battery with those of the charger and slide the
battery all the way until it snaps into place. The red LED (F)
will light up indicating the charging procedure has begun.
Once the green LED (E) lights up, the battery is fully charged
and ready to use. Press the battery clip (B) Fig.3 to remove
battery from charger.
Installing/removing battery from impact driver
To install a battery (A) Fig.3 to the base of the cordless
impact driver, align the grooves the battery with those of the
impact base and slide the battery all the way until the battery
clip (B) snaps and holds the battery into place.
To remove the battery from the base, press the battery clip
(B) Fig.3 and slide the battery away from the base.
Variable speed trigger
Your cordless impact driver is equipped with a variable
speed trigger (A) Fig.4. The speed can be controled from the
minimum to the maximum RPM just by the pressure applied
to the trigger switch. Apply more pressure to increase speed
and apply less pressure to decrease speed. Release trigger
to stop impact driver.
Forward/reverse switch and trigger lock
Your cordless impact driver is equipped with a
forward/reverse switch and trigger lock (B) Fig.4. It is located
above the trigger. This switch is designed to change the
direction of rotation of the chuck and to lock the trigger to
help prevent accidental starts and battery discharge. For a
forward rotation (with the chuck pointing away from you) move the lever to the left. For reverse
rotation move the lever to the right. To lock the trigger, place the lever in the centre position.
WARNING! Do not change the rotation direction until the impact driver chuck has come
to a complete stop. Changing the rotation during an operation can cause damage to the
tool.
Electric brake
This impact driver is equipped with an electric brake. If the tool consistantly fails to stop quickly
after the trigger is released, have the tool serviced.
Figure 2
Figure 3
Figure 4
OPERATION & MAINTENANCE
LED lights
Your cordless impact driver features a LED light system with
three LEDs (A) Fig.5 which gets activated by pressing the
trigger. This feature is ideal when working in partially lit work
environments.
Inserting/removingdriver bit or nut driver into 1/4” quick
release chuck
Warning! Only use 1/4” driver bits or nut drivers with
identical dimensions as shown in Fig.6. Do not use any other
driver bits or nut drivers.
To install a driver bit or nut driver (C) Fig.7 into the 1/4” hex.
chuck (A), pull the chuck collar (B) Fig.7 away from the
impact driver and insert the bit into the chuck as far as it will
go. Release the collar to lock the driver bit into place.
Warning! If the driver bit is not fully inserted into the chuck,
the chuck collar will not return to the original position when
released and the driver bit will not lock into place.
To remove the driver bit, pull the chuck collar away from the
impact driver and pull the driver bit out.
Impact action
When this impact driver reaches a certain torque, the impact
function is engaged and a clicking sound will be heard, this
is normal.
MAINTENANCE
WARNING: NO USER SERVICE-ABLE PARTS INSIDE
Preventative maintance performed by an unauthorized
personnel may result in the misplacement of internal wires
and componenets which could cause serious hazards. We
recommend that all servicing be performed by a qualified
KING CANADA service centre technician.
Battery
Pay attention to the battery power levels as the battery nears
its end of life. If you notice a decrease in battery performance or a significant difference in
running power between charges, then it is time to replace the battery. Failure to do so may
damage the charger and cause improper operation.
Tool lubrication
This tool has been properly lubricated and will never require additionnal lubrication.
Cleaning
To avoid accidents, always remove the battery from the cordless impact before cleaning. The
tool is most effectively cleaned with the use of an air compressor. Always wear safety glasses
when using an air compressor. Ventilation openings and switch levers must be kept clean and
free of foreign objects. Do not insert pointed objects through these openings in the attempt to
clean them.
1. Air vents of the tool should be cleaned regularly to avoid overheating of the motor which is
caused by the blocking of the air vents.
2. DON’T clean this tool with water, as no liquid is allowed in the tool body. Clean the tool with
a dry clean cloth only. Compressed air at low pressure is also suitable.
3. DON’T allow petroleum based products to come into contact with the plastic parts of the tool,
as they contain chemicals that can damage or destroy the plastic parts.
Figure 5
Figure 7
Figure 6
-
1
-
2
-
3
-
4
King Canada 8055L is a 20V MAX Lithium-ion Cordless Impact Driver that combines power and versatility for a wide range of driving applications. Ideal for both professional and DIY enthusiasts, it features a variable speed trigger for precise control, a 1/4-inch hex quick-release chuck for easy bit changes, and an LED work light for illuminating dark workspaces. With a maximum torque of [value not provided], this impact driver delivers impressive power for driving screws, nuts, and bolts into various materials.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
King Canada 8020L/8022LK User manual
-
-
-
-
-
-
-
-
-