N13275
30cm Soft Blade Fan
BRIO30
Instruction Manual
AFTER SALES SUPPORT
NZ: 0800 836 761
AU: 1300 886 649
IMPORTANT SAFETY INSTRUCTIONS
Read these instructions before use and keep in a safe place. Remove the packaging
and make sure that the appliance is intact. If in doubt, do not use it and contact
qualied personnel only. Packaging materials (plastic bags, polystyrene, staples etc.)
must be kept out of the reach of children as they could be hazardous.
• The appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
• Young children should be supervised to ensure that they do not play with
the appliance.
CAUTION:
• The appliance must only be used by responsible adults; for their own safety,
children and persons with reduced mental capacities must not use the
appliance unless under the supervision of responsible adults.Children should
not use the appliance as a game, but should always be supervised by a
responsible adult.
• Before connecting the appliance, check that the appliance rating corresponds
to the mains rating.
• If the power cable is damaged, it must be replaced by the manufacturer or by its
after sales service or otherwise by a qualied person in order to prevent any risk.
• This appliance must only be used for the purpose for which it has been
manufactured, i.e. as a ceiling fan. The manufacturer is not responsible for any
damage caused by improper or incorrect use.
• Before cleaning or carrying out maintenance on the appliance, disconnect it
from the electrical mains by switching o the system switch.
• If the appliance is faulty and/or operating incorrectly, switch it o without
tampering with it. If any repair is required, please contact our after-sale centres
only and ask for original spare parts. If the above is disregarded, the safety of
the appliance may be compromised.
• Switch o the appliance when not in use.
• The use of any electrical appliance calls for the awareness of some basic rules,
such as: do not use the appliance near sources of water such as baths, showers
or swimming pools, do not touch the device with wet or damp hands or feet,
do not leave the appliance exposed to atmospheric agents
• Max. ambient temperature 40°C.
• Do not use the appliance in the presence of potentially ammable or explosive
liquids or gases.
PARTS OF YOUR FAN
ASSEMBLING
1. Unscrew the spinner clockwise and the nut counter-clockwise then remove
both of them.
2. Use “Base Screw” to screw “Base & Fan Pillar” tightly, and then cover the “Base
C o v e r ”.
3. Install” Rear Guard” in proper position with handle up and screw the screw.
4. Screw on plastic nut tightly to attach rear guard.
5. Set the “Rear Guard” into the “Round ring” in the proper position.
6. Install “Fan Blades” into “Blade Holder” in the proper position and then x onto
motor shaft.
7. Cover “Blade Holder Cover”
8. Screw “Spinner” on to motor shaft counter-clockwise, to prevent the spinner
can be removed by hand, please screw the screw at the centre of “Spinner”,
then put the rubber protector to cover the screw carefully.
9. Fix “Front Guard” into “Round Ring” in the proper position.
4
ASSEMBLING
1. Unscrew the spinner clockwise and the nut counter-clockwise then remove both
of them
2. Use “Base Screw” to screw “Base & Fan Pillar” tightly, and then cover the “Base
Cover”
3. Install” Rear Guard” in proper position with handle up and screw the screw.
4. Screw on plastic nut tightly to attach rear guard
5. Set the “Rear Guard” into the “Round ring” in the proper position
6. Install “Fan Blades” into “Blade Holder” in the proper position and then fix onto
motor shaft
7. Cover “Blade Holder Cover”
8. Screw “Spinner” on to motor shaft counter-clockwise, to prevent the spinner can
be removed by hand, please screw the screw at the centre of “Spinner”, then put
the rubber protector to cover the screw carefully.
9. Fix “Front Guard” into “Round Ring” in the proper position
OPERATING
Place the appliance on a dry and flat surface. Operate the appliance with the noted
power voltage which was marked on the appliance (A.C. only). Do not immerse the
appliance into water; use a damp cloth to wipe the body and a dry one to wipe over
the water. Note: please let the appliance cool down fully before cleaning.
1. Plug the power supply cord into
a wall outlet.
2. To make/stop the fan head
oscillate, pushes down/pull the
clutch knob.
3. To adjust the airflow upward or
mild downward, simply adjust
the grille to desired angle by
hand freely, must shut down
the fan before the adjustment.
4. Speed is controlled by Speed
switch.
4
ASSEMBLING
1. Unscrew the spinner clockwise and the nut counter-clockwise then remove both
of them
2. Use “Base Screw” to screw “Base & Fan Pillar” tightly, and then cover the “Base
Cover”
3. Install” Rear Guard” in proper position with handle up and screw the screw.
4. Screw on plastic nut tightly to attach rear guard
5. Set the “Rear Guard” into the “Round ring” in the proper position
6. Install “Fan Blades” into “Blade Holder” in the proper position and then fix onto
motor shaft
7. Cover “Blade Holder Cover”
8. Screw “Spinner” on to motor shaft counter-clockwise, to prevent the spinner can
be removed by hand, please screw the screw at the centre of “Spinner”, then put
the rubber protector to cover the screw carefully.
9. Fix “Front Guard” into “Round Ring” in the proper position
O PERATING
Place the appliance on a dry and flat surface. Operate the appliance with the noted
power voltage which was marked on the appliance (A.C. only). Do not immerse the
appliance into water; use a damp cloth to wipe the body and a dry one to wipe over
the water. Note: please let the appliance cool down fully before cleaning.
1. Plug the power supply cord into
a wall outlet.
2. To make/stop the fan head
oscillate, pushes down/pull the
clutch knob.
3. To adjust the airflow upward or
mild downward, simply adjust
the grille to desired angle by
hand freely, must shut down
the fan before the adjustment.
4. Speed is controlled by Speed
switch.
Distributed by Tempo (Aust) Pty Ltd ABN 70 106 100 252
Unit 8/14 Rodborough Rd, Frenchs Forest, Australia NSW 2086
Customer Help Line : 1300 886 649 (AU) | 0800 836 761 (NZ)
Telephone: (02) 9975 2199 Fax: (02) 9975 2688
Email: info@tempoaustralia.com.au
OPERATION
Place the appliance on a dry and at surface. Operate the appliance with the noted
power voltage which was marked on the appliance (A.C. only). Do not immerse the
appliance into water; use a damp cloth to wipe the body and a dry one to wipe over
the water. Note: please let the appliance cool down fully before cleaning.
MAINTENANCE
Before carrying out routine cleaning, switch o the fan and disconnect mains power.
Use a soft, damp cloth only and do not use abrasive substances.
NOTE: Do not submerge any part of the fan in the water.
1. Plug the power supply cord into a
wall outlet.
2. To make/stop the fan head oscillate,
pushes down/pull the clutch knob.
3. To adjust the airow upward or mild
downward, simply adjust the grille
to desired angle by hand freely,
must shut down the fan before the
adjustment.
4. Speed is controlled by Speed switch.
RECYCLING
At the end of its working life, do not throw this appliance out with your household
rubbish. Observe any local regulations regarding the disposal of electrical consum-
er goods and dispose of it appropriately for recycling. Contact your local authorities
for advice on recycling facilities in your area.
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Unbranded XXCI-CR User guide
-
Campomatic SF200R SF300R Owner's manual
-
-
Orieme BRIO 40 C User manual
-
Coopers of Stortford K319 User manual
-
Hitachi UZ557000 User manual
-
Orieme BRIO 30 R User manual
-
-
Goldair GCPF315 User manual
-
