MountzPro MountzProDT135 Owner's manual

OWNER’S MANUAL

MountzPro Digital Flex Head Torque Wrench

TM

Mountz, Inc.

1080 N. 11th Street

San Jose, CA 95112

888-925-2763

www.mountzpro.com

Wrench Components

Push Button

Socket Release

Handle

Function Panel

Digital LCD Display

Battery Cap

TM

Ratchet Direction

Switch

TM

Wrench Torque Ranges & Specications

Torque Ranges Sq. Drive Length

Model Item # lbf.ft lbf.in N.m in. mm

MountzProDT135

MP320000 11-99 lbf.ft 132-1198 lbf.in 15 - 135 n.M 3/8” 15 3/4” 400

MountzProDT135

MP320000 11-99 lbf.ft 132-1198 lbf.in 15 - 135 n.M 1/2” 22 3/4” 570

TM

Battery

1. Remove screw that secures the

end-cap of the handle with PH2

screwdriver and remove end-cap.

2. Position battery to the correct orientation by

following the Positive and Negative markings on

the handle and insert battery.

3. Replace end-cap and secure the

screw.

• Use (9v) battery only. Wrong battery usage may

lead to broken battery or electrolyte leaking, and

damage or break down torque wrench.

• Remove battery if wrench will not be used for a

long period of time.

• Replace a dead battery as soon as possible.

Attention:

TM

Digital Display & Functional Panel

Audible Alert

Red LED Light

Green LED Light

Clear

Torque Value Set /Save

Value

+

Value -

Tolerance

Battery Indicator

Digital LCD

Unit Selection

Power on: Press any key for 3 seconds Power o: Auto Shut o after 90 seconds or

Hold CLR for 5 seconds

Setting Torque Wrench : Selecting Units

Press UNI to select the desired torque measurement unit

Unit: Newton Meters - N.m

Unit: Foot Pounds - lbf.ft

Unit: Inch Pounds - lbf.in

Unit: Kilogram Force Meters - kgf.m

TM

Setting Torque Wrench : Setting Torque

Press SET to change the desired torque value

When the desired torque value is reached,

press SET to save the value

Press the Up or Down arrows to change the target torque value

TM

Setting Torque Wrench : Setting Alarm Tolerance

Press % to change the desired tolerance value

Press the Up or Down arrows to change the target tolerance value

When the desired tolerance value is reached, press % to save the value

TM

Tolerance Example

If the torque wrench is set to 45 lbf.ft and the tolerance is set at 10%, then an alert tone will occur at 40.5 lbf.ft. There will be a

rapid pulsing tone to indicate the torque value is closing to the target value of 45 lbf.ft.

45

40.5

{

Tolerance 10%

Rapid Pulsing Tone

LBF.FT

TM

T

Operating Torque Wrench

• Be sure not to apply torque when the wrench has not been powered on. To power on wrench, press and hold any button for 3

seconds.

• Use correct size socket for the applied torque load.

• Apply force in steady and smooth manner.

• Press CLR to manual clear ending torque value or begin a new tightening and the wrench will clear automatically.

• When approaching target torque the wrench will begin producing a rapid pulsing tone and ashing the Green LED when the

tolerance threshold is reached.

• When the applied torque reaches the target torque the Green & Red LED are solid as well as the audible tone and the wrench

handle will vibrate. Stop applying force at this point.

TM

Warnings

• Low Battery

-When battery capacity is 30% remaining, the battery icon on the display ashes. The wrench is still usable, however

battery should be replaced soon.

-When Battery capacity is 10% remaining, the display will only show the battery icon and the wrench will not function.

Replace battery.

• Over torquing can cause damage to the tool.

• Verify the calibration of the wrench if you know or suspect its capacity has been exceeded.

• Never use the wrench with the power o.

• Do not press any buttons while torque is being applied.

TM

Mountz, Inc.

1080 N. 11th Street

San Jose, CA 95112

888-925-2763

www.mountzpro.com

MountzPro MountzProDT135 Owner's manual

MountzPro MountzProDT135 Owner's manual

Other documents