Childcare 089420 Owner's manual

Brand: Childcare

Model: 089420

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

DELUXE UNIVERSAL

HEARTH GATE

Model # 089420

IMPORTANT: RETAIN FOR FUTURE

REFERENCE, READ CAREFULLY

This product has been designed for use with children up to 24 months of age.

This product has been designed and manufactured to comply with the Safety Standard ASTM F1004.

When used as a safety gate, never use without wall ttings.

When used as a hearth gate, always place the gate minimum 75cm away from the source of heat / re and minimum 90cm from

open re.

Since every replace / wood burning stove reaches different temperatures, the above placing is only intended as a guideline. Test

your own unit at maximum heat output before placing the gate. If the gate is hot to touch, move gate further from heat source than

the recommended minimum distance.

Check and tighten mountings regularly.

Never allow child to climb or swing on gate.

Do not use if any part of gate is broken or missing.

When folded, store away from children.

This product will not necessarily prevent all accidents.

Never leave child unattended.

Use only approved spare parts and accessories from the manufacturer.

Use only with locking mechanism securely engaged.

Install according to the manufacturer’s instructions.

When used as a re surround, this product is not a re guard. It is intended to keep children away from the area surrounding the

replace.

Do not leave anything in the hearth gate which could provide a foothold or create a danger of suffocation or strangulation.

When used as a hearth gate be aware of the risk of open re and other sources of strong heat, such as electric bar res, gas res,

etc in the vicinity of the hearth gate.

Read all instructions before assembly and use of the gate. Keep

instructions for future use.

Safety Precautions

TO PREVENT SERIOUS INJURY OR DEATH, SECURELY

INSTALL GATE OR ENCLOSURE AND USE ACCORDING TO

MANUFACTURER’S INSTRUCTIONS.

NEVER LEAVE CHILD UNATTENDED.

NEVER USE WITH A CHILD ABLE TO CLIMB OVER OR DISLODGE/

OPEN THE GATE OR ENCLOSURE.

THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL

ACCIDENTS.

USE ONLY WITH LOCKING/LATCHING MECHANISM SECURELY

ENGAGED.

WARNING

DO NOT FORCE HINGES

Please read the instructions regarding adjusting the hinge position on page 5 or 9

Due to variations in the style and design of our products, the photographs and illustrations

shown in this instruction manual are generic, therefore product fabrics, colour and

design may vary from images shown. CNP Brands reserves the right to alter product

specications without notice as a result of our ongoing policy of product improvement.

Contents

Assembly contents list

Assembly / Operating instructions

How to care for your Childcare Gate

Congratulations on your purchase of the

Childcare Deluxe Universal Hearth Gate.

This product has been designed and developed with

safety, comfort and functionality in mind. Please take

the time to read this manual carefully before using

this product and keep it in a safe place for future

reference.

Supplied loose in box:

Assembly Contents

Check what you have received...

You have received 1 box. Please check the contents of the box against the list below. If anything is

missing, please contact Customer Service. In Australia, contact CNP Brands on 1300 667 137, in

New Zealand contact Wainhouse Distribution on 0800 567 5000.

Hearth Gate

(6 sections)

Lower bracket

slider

Upper bracket

Wall plates

Removable

vertical bar

(pre-assembled

in hearth gate)

Bottom hinge

caps with groove

(pre-assembled)

Bottom hinge

cap plain

(pre-assembled)

Hinge cones

(pre-assembled)

Top hinge cap

(rounded)

(pre-assembled)

Wood screws

Lower bracket

bolt and nut

Mattress

Assembly / Operating Instructions

Setting up as Play Den

1. Unpack the hearth gate on a stable surface making sure the

handle is on the top.

2. Unfold the sections by pushing in

the button on the join and turning

the sections. If required, lift the top

section slightly while pushing the

button.

3. Unfold the hearth gate into either a hexagon or square. The

markings on the top of the hinges indicate the position to unfold

each hinge for either hexagon or square conguration.

4. The removable vertical bar has been tted into the end section

by the manufacturers. Lift up the vertical bar and remove it by

sliding it out of the lower hinge.

Assembly / Operating Instructions

Setting up as Play Den (cont)

5. Remove the pre-assembled

hinge cone and top and

bottom hinge caps from the

ends of the den which are to

be joined together.

6. Connect the two sections by aligning the ends of the sections

and ensuring that the hinges drop together on both the top and

the bottom.

7. Push the vertical bar up into the

top hinge and then slide into the

groove in the bottom hinge. Ensure

the vertical bar is inserted with the

protruding rod at the top.

Assembly / Operating Instructions

To open the gate

Squeeze the handle tightly and slide

lock across at the same time. The gate

may then be opened in either direction.

To close the gate

Squeeze the handle tightly and slide the lock at the same time. Align

the gate and gate frame. Release the handle and the gate should lock

correctly. Please note that the gate will be properly secured when the

locking bar has also engaged in the bottom of the gate frame.

Positioning as Hearth Gate around a ﬁreplace

1. When used as a hearth barrier around a replace, the distance between the replace /

hearth and gate sections must be a minimum of 75cm. The gate must never be setup in a

straight line. Should it not be possible to keep the recommended minimum distances, gate

extensions are available for purchase.

2. When used as a hearth barrier around an open re, the distance between the replace and

gate sections must be a minimum of 90cm. The gate must never be setup in a straight line.

WARNING: The minimum distances suggested between replace and gates are only

recommended distances sincce every replace / wood burning stove reaches different

temperatures. Test your unit at maximum heat output before nal placing of the gate.

Place the gate according to the instructions at maximum heat output. If the gate is too hot to

touch, move gate further from the heat source than recommended.

Assembly / Operating Instructions

Positioning the Hearth Gate at the bottom of stairs

If the gate is to be positioned at the bottom of stairs. please note the

following:

• The gate must be setup in a curve away from the stairs.

• The gate must be placed as far away from the stairs as possible

so that the child will not be able to reach the bottom stair and

climb over the gate.

• There must be a minimum distance of 40cm between gate and

stairs.

Should it not be possible to keep the recommended minimum

distances, gate extensions are available for purchase.

Positioning the Hearth Gate at the top of stairs

If the gate is to be positioned at the top of stairs. please note the

following:

• The gate must be setup in a curve away from the stairs.

• The gate must never be setup in a straight line.

• There must be a minimum distance of 40cm between gate and

stairs.

Should it not be possible to keep the recommended minimum

distances, gate extensions are available for purchase.

Positioning the Hearth Gate in general

Please note that the child is able to reach through the bars, therefore

ensure the gate is placed far enough away from other objects. The

gate must never be setup in a straight line.

PLEASE NOTE:

With 3 sections, the gate ts openings from 90-180cm

With 5 sections, the gate ts openings from 90-300cm

With 6 sections, the gate ts openings from 90-360cm

Assembly / Operating Instructions

Setting up as Hearth Gate and Conﬁgure Gate

1. Unpack the hearth gate on a stable surface making sure the

handle is on the top.

2. Unfold the sections by pushing in

the button on the join and turning

the sections. If required, lift the top

section slightly while pushing the

button.

3. Unfold the hearth gate into either a hexagon or square. The

markings on the top of the hinges indicate the position to unfold

each hinge for either hexagon or square conguration.

4. The removable vertical bar has been tted into the end section

by the manufacturers. Lift up the vertical bar and remove it by

sliding it out of the lower hinge.

5. Remove the hinge cone from the upper hinge and the hinge cap

from the lower rail.

Assembly / Operating Instructions

Setting up as Hearth Gate and Conﬁgure Gate

6. Connect the two sections by aligning the ends of the sections

and ensuring that the hinges drop together on both the top and

the bottom.

Fitting the mattress

1. Pass the elastic underneath three

of the hinges.

2. Remove the vertical removable bar,

and loop the elastic around the slot

in the hinge before replacing the

vertical bar.

3. Loop the remaining elastic

underneath and around the

remaining three hinges.

7. Push the vertical bar up into the

top hinge and then slide into the

groove in the bottom hinge. Ensure

the vertical bar is inserted with the

protruding rod at the top.

Assembly / Operating Instructions

Installing wall ﬁttings

1. Attach the upper wall bracket to the cone hinge.

2. Push the vertical bar up into the top hinge. Ensure the vertical

bar is inserted with the narrow section at the top.

3. Slide the lower bracket onto the

removable bar and slide into the

lower bracket.

4. Repeat steps 1-3 for other end of

gate.

5. Place the congure gate in the

desired location.

6. Rotate upper and lower brackets

until ush against the mounting

surface. With a pencil, outline

brackets on the mounting surface.

NOTE: Lower bracket is adjustable.

It can be moved up (maximum

15cm) to accomodate various

heights of oor moulding; and

by loosening screw, can adjust

widths to accomodate uneven wall

construction.

Max

15cm

Assembly / Operating Instructions

Installing wall ﬁttings (cont.)

7. Remove wall plates from brackets

by pressing locking tabs on the wall

plates and lifting off.

8. Hold one wall plate inside outline on wall and attach using two

wood screws. Repeat for other wall plates.

PLEASE NOTE: Screws provided are for mounting directly

into wood. If mounting into brick, drywall or other surfaces, use

appropriate hardware.

9. Reattach brackets at both ends of the gate to the wall plates.

Gate should now be properly installed.

Assembly / Operating Instructions

Adding optional sections

An extension has a top hinge on one side and a cone hinge on the other side. This makes it

possible to t the extension in a range of congurations.

1. The removable vertical bar has been tted by the manufacturer.

Remove the bar by lifting it up and sliding it out of the lower

hinge.

2. Fit the extension in place by placing the top hinge on the hearth

gate over the cone hinge on the extension. The hinges must be

aligned on both top and bottom.

3. Let the hinges drop together and insert the removable vertical

bar.

Assembly / Operating Instructions

Removing sections

To remove a section, always remove the

end sections. Remove the removable

vertical bar by lifting it up and sliding it

out of the lower hinge. Lift the section off

the hearth gate.

Fitting hinge caps / covers

Depending on the number of sections

removed or added, you will need to t

the appropriate caps and covers to the

end sections as shown.

Cleaning

To ensure the long-lasting use of your gate, wipe down with a damp cloth and use a mild soap

solution if necessary. Do not use abrasive cleaners. Always store product in a clean dry place.

Maintenance

Always check parts regularly for tightness of screws, nuts and other fasteners – tighten or replace

if required. To maintain the safety of your gate, seek prompt repairs for bent, torn, worn or broken

parts. Use only those parts and accessories approved by CNP Brands.

If you have any difculties in assembling the gate, please contact our Service Department. In

Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution

on 0800 567 5000.

How to care for your Hearth Gate

Distributed in Australia by CNP Brands, 20 Calarco Drive, VIC, 3030

Customer Service 1300 667 137 www.cnpbrands.com.au

Distributed in New Zealand by Wainhouse Distribution, 2-6 Argyle St,

Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand

Customer Service: 0800 567 5000 [email protected]

Childcare 089420 Owner's manual

Brand: Childcare

Model: 089420

Category: Fireplaces

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Childcare 089420 Owner's manual

This manual is also suitable for

Childcare 089420 Owner's manual

Related papers

Other documents