Teltonika RUT955 User manual

Brand: Teltonika

Model: RUT955

Type: User manual

https://wiki.teltonika.lt/

contents in this document in any form without the prior written permission of TELTONIKA Ltd is prohibited. The manufac-

turer reserves the right to modify the product and manual for the purpose of technical improvement without prior notice.

Other product and company names mentioned herein may be trademarks or trade names of their respective owners.

LEGAL NOTICE

ATTENTION

To avoid voltage caused traumas please follow these safety requirements:

- The device is intended to be powered from a Limited Power Source (LPS) that does not exceed 15 W in power consumption

and the current rating of overcurrent protective device should not exceed 2 A.

- The highest transient overvoltage in the output (secondary circuit) of used PSU shall not exceed 36 V peak.

- The device can be used with a Personal Computer (ﬁrst safety class) or Notebook (second safety class). Associated equipment:

PSU (power supply unit) (LPS) and personal computer (PC) shall comply with the requirements of standard EN 60950-1.

- To avoid mechanical damage to the device it is recommended to transport it packed in a damage-proof pack.

When using the device it should be placed so that its indicating LEDs would be visible as they inform in which working mode the

device is in and if it has any working problems.

Protection against over current, short circuiting and earth faults should be provided as a part of the building installation.

SAFETY

FRONT VIEW

BACK VIEW

Mobile AUX antenna connector Mobile MAIN antenna connector

Reset button

WiFi antenna

connectors

LAN LEDs

WAN Ethernet portLAN Ethernet ports

Mobile

signal strength

indication LEDs

Power socket

Power LED Mobile connection status LED

WAN LED

1. Push the SIM holder button with the SIM needle.

2. Pull out the SIM holder.

3. Insert your SIM card into the SIM holder.

4. Slide the SIM holder back into the router.

5. Attach LTE and WiFi antennas (max torque 0.9 Nm 8.0 in-lbs).

6. Connect the power adapter to the socket on the front of the device. Then plug the other end of the power adapter

into a power outlet.

7. Connect to the device wirelessly (SSID: RUT950_**** (unique to each device)) or use an Ethernet cable (connected

to LAN port).

HARDWARE INSTALLATION

POWER SOCKET PINOUT

SIGNAL STRENGTH LEDS

- Constant blinking (~ 2Hz) – router is turning on.

- LED turned oﬀ – no 4G data connection, LED turned on – 4G data connection.

- Green and red blinking alternatively ever 500 ms: no SIM or bad PIN.

- Green, red and yellow blinking alternatively every 500 ms: connecting to GSM.

- Red blinking every 1 sec: connected 2G, but no data session established.

- Yellow blinking every 1 sec: connected 3G, no data session established.

- Green blinking every 1 sec: connected 4G, no data session established.

- Red lit and blinking rapidly while data is being transferred: connected 2G with

data session.

- Yellow lit and blinking rapidly while data is being transferred: connected 3G

with data session.

- Green lit and blinking rapidly while data is being transferred: connected 4G

with data session.

LED INDICATIONS

1. To enter the router's Web interface (WebUI), type http://192.168.1.1 into the URL ﬁeld of your Internet browser.

2. Use login information shown in image A when prompted for authentication.

3. After you log in, you will be prompted to change your password for security reasons. The new password must

contain at least 8 characters, including at least one uppercase letter, one lowercase letter, and one digit. This step is

mandatory, and you will not be able to interact with the router's WebUI before you change the password.

4. When you change the router's password, the Conﬁguration Wizard will start. The Conﬁguration Wizard is a tool

used to set up some of the router's main operating parameters.

5. Go to the Status > Network page and pay attention to the Signal Strength indication (image B). To maximize the

cellular performance try adjusting the antennas or changing the location of your device to achieve the best signal

conditions.

Mobile Information

Mobile

Data connection state

IMEI

IMSI

Sim card state

Signal strength

Connected

123456789012345

Ready

-79 dBm

http://192.168.1.1

Please enter username and password

Username

Password

admin

admin01

GPL

Some products of Teltonika partly contain software code developed by third parties, including software code subject to the

GNU General Public License (“GPL”) version 2, version 3, GNU Lesser General Public License (“LGPL”) version 2.1 and other

open source licenses.

In order to comply with the terms of the GPL, Teltonika, where applicable, oﬀers a mail in service of a machine readable

source code of the software subject to the GPL, on an optical media (CD-ROM) upon request by mail or email. Further

information is provided with the relevant products or the software. You can download the free copies of the respective

machine readable source code of the software which is subject to the GPL and contained in Teltonika products if you follow

this internet link: https://wiki.teltonika.lt/index.php?title=GPL

The respective programs are distributed WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABI-

LITY or FITNESS FOR A PARTICULAR PURPOSE. See the respective GNU General Public License for more details.

Please choose the model and version of your Teltonika product from the list found in the provided link in order to

download the source code. You can also review and print the respective GPL license terms.

If you have any more questions or suggestions regarding GPL, please contact us at [email protected]

SPECIFICATIONS

- IEEE 802.3, IEEE 802.3u standards

- 3 x LAN ports, 10/100 Mbps

- 1 x WAN port (can be conﬁgured to LAN) 10/100 Mbps

- Supports Auto MDI/MDIX

ETHERNET

- IEEE 802.11b/g/n WiFi standards

- 2x2 MIMO

- Access Point (AP), Station (STA) modes

- WPA, WPA2, WPA&WPA2 encryption methods

- 2.401 – 2.483 GHz WiFi frequency range*

- 20 dBm max WiFi TX power

- SSID stealth mode and access control based on MAC address

- Up to 100 simultaneous connections

- Captive portal (Hotspot), internal/external Radius server

- Built in customizable hotspot landing page

Wi-Fi

- High performance 550 MHz CPU with 128 MB of DDR2 memory

- 16 MB SPI Flash memory

- 4 pin industrial DC power socket

- External SIM holders, 2 x SIM slots (Mini SIM – 2FF, 2st form factor)

- Reset/restore to default button

- 2 x SMA for LTE, 2 x RP-SMA for WiFi antenna connectors

- 4 x LAN status LEDs, 1 x Power LED

- 1 x bi-color connection status LED, 5 x connection strength LEDs

- DIN rail (can be mounted on two sides), ﬂat surface placement

HARDWARE

*Supported frequency bands are dependent on geographical location and

may not be available in all markets

ELECTRICAL, MECHANICAL & ENVIRONMENTAL

- 40 °C to 75 °C Operating temperature

235 gWeight

80 mm x 106 mm x 46 mm Dimensions (W x D x H)

100 – 240 VAC -> 9 VDC wall adapterPower supply

9 – 30 VDC Input voltage range

< 2W idle, < 7W MaxPower consumption

10 % to 90 % Non-condensingOperating humidity

- 45 °C to 80 °CStorage temperature

5 % to 95 % Non-condensingStorage humidity

TECHNICAL INFORMATION

*Order code dependent.

**Higher gain antenna can be connected to compensate for cable attenuation when a cable is used. The user is responsible for the compliance with the legal regulations.

Radio speciﬁcations

Bundled antennas speciﬁcations*

RF technologies

Max RF power

GSM, GPRS, EDGE, UMTS/HSPA+, LTE, GNSS, WiFi

33 dBm@GSM, 24 dBm@WCDMA, 23 dBm@LTE, 20 dBm@WiFi

GSM/WCDMA/LTE antenna 698~960/1710~2690 MHz, 50 Ω, VSWR<3, gain** 3 dBi, omnidirectional, SMA male connector

WiFi antenna 2400~2483.5 MHz, 50 Ω, VSWR<2, gain** 5 dBi, omnidirectional, RP-SMA male connector

https://wiki.teltonika.lt/

RUT950 router must be used in compliance with any and all applicable national and international laws and with any special restrictions regulating the utilization of the

communication module in prescribed applications and environments.

SAFETY INFORMATION

[EN] English Hereby, TELTONIKA declares that this RUT950 is in compliance with the essential requirements and other relevant provisions of

Directive CE/RED.

[BG] Bulgarian С настоящето, TELTONIKA декларира, че RUT950 е в съответствие със съществените изисквания и другитеприложими разпоредби на

Директива CE/RED.

[CZ] Czech TELTONIKA tímto prohlašuje, že RUT950 splňuje základní požadavky a všechna příslušná ustanoveni Směrnice CE/RED.

[DE] German Hiermit erklärt TELTONIKA dass sich das Gerät RUT950 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen

einschlägigen Bestimmungen der Richtlinie CE/RED beﬁndet.

[DK] Danish Undertegnede TELTONIKA erklærer herved, at følgende udstyr RUT950 overholder de væsentlige krav og øvrige relevante krav i direktiv CE/RED.

[EE] Estonian Käesolevaga kinnitab TELTONIKA seadme RUT950 vastavust direktiivi CE/RED põhinõuetele ja nimetatud direktiivist tulenevatele teistele

asjakohastele sätetele.

[ES] Spanish Por la presente, TELTONIKA declara que este RUT950 cumple con los requisitos esenciales y otras exigencias relevantes de la Directiva CE/RED.

[FI] Finish TELTONIKA vakuuttaa täten että RUT950 tyyppinen laite on direktiivin CE/RED oleellisten vaatimusten ja sitä koskevien direktiivin muiden

ehtojen mukainen.

[FR] French TELTONIKA déclare que cette RUT950 est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive CE /RED.

[GR] Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Ο ΚΑΤΑΣΚΕΥΑΣΤΗΣ TELTONIKA ΔΗΛΩΝΕΙ ΟΤΙ RUT950 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ

ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ CE/RED.

[HU] Hungarian A TELTONIKA ezzennel kijelenti, hogy a RUT950 típusú berendezés teljesíti az alapvető követelményeket és más CE/RED irányelvben

meghatározott vonatkozó rendelkezéseket.

[IT] Italian Con la presente TELTONIKA dichiara che questo RUT950 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla

direttiva CE/RED.

[LT] Lithuanian Šiuo dokumentu UAB TELTONIKA deklaruoja, kad šis RUT950 atitinka esminius reikalavimus ir kitas CE/RED Direktyvos nuostatas.

[LV] Latvian Ar šo TELTONIKA deklarē, ka RUT950 atbilst Direktīvas CE/RED būtiskajām prasībām un citiem ar to saistītajiem noteikumiem.

[NL] Dutch Hierbij verklaart TELTONIKA dat het toestel l RUT950 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van

richtlijn CE/RED.

[NO] Norwegian TELTONIKA Erklærer herved at RUT950 er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv CE/RED.

[PL] Polish Niniejszym TELTONIKA deklaruje że RUT950 jest zgodny z zasadniczymi wymaganiami i innymi właściwymi postanowieniami Dyrektywy CE/RED.

[PT] Portuguese Eu, TELTONIKA declaro que o RUT950 cumpre os requisitos essenciais e outras provisões relevantes da Directiva CE/RED.

[RO] Romanian Prin prezenta, TELTONIKA declară că aparatul RUT950 este în conformitate cu cerinţele esenţiale şi cu alte prevederi pertinente ale Directivei

CE/RED.

[SE] Swedish Härmed intygar TELTONIKA att denna RUT950 är i överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser

som framgår av direktiv CE/RED.

[SI] Slovenian TELTONIKA izjavlja, da je ta RUT950 v skladu z bistvenimi zahtevami in drugimi relevantnimi določili direktive CE/RED.

[EN] Instruction Manual: Connect the power adapter to turn on the device. Open 192.168.1.1 in your web browser to conﬁgure it. More information on

https://wiki.teltonika.lt

[BG] Инструкция: Свържете адаптера на захранване, за да включите устройството. Отворете 192.168.1.1 в уеб браузър, за да настроите продукта.

Повече информация в https://wiki.teltonika.lt

[CZ] Návod k použití: Připojte napájecí adaptér k zapnutí přístroje. Otevřete 192.168.1.1 ve webovém prohlížeči pro konﬁguraci produktu. Více informací najdete

v https://wiki.teltonika.lt

[DE] Bedienungsanleitung: Verbinden Sie das Netzteil, um das Gerät einzuschalten. Öﬀnen Sie 192.168.1.1 in einem Web Browser, um das Produkt zu

konﬁgurieren. Weitere Informationen im https://wiki.teltonika.lt

[DK] Instruktionsbog: Tilslut strømadapteren for at tænde for enheden. Åbn 192.168.1.1 i en webbrowser til at konﬁgurere produktet. Mere information i

https://wiki.teltonika.lt

[EE] Kasutusjuhend: Ühendage toiteadapter seadme sisselülitamiseks. Avatud 192.168.1.1 in veebilehitseja seadistada toodet. Rohkem teavet

https://wiki.teltonika.lt

[ES] Manual de instrucciones: Conecte el adaptador de alimentación para encender la unidad. Abra 192.168.1.1 en un navegador web para conﬁgurar el

producto. Más información en https://wiki.teltonika.lt

[FI] Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.1.1 in selaimen määrittää tuotteen. Lisää tietoa https://wiki.teltonika.lt

[FR] Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.1.1 dans un navigateur Web pour conﬁgurer le produit. Plus

d'informations dans https://wiki.teltonika.lt

[GR] εγχειρίδιο οδηγιών: Συνδέστε τον προσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.1.1 σε ένα πρόγραμμα περιήγησης στο

Web για να διαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο https://wiki.teltonika.lt

[HU] Használati utasítás: Csatlakoztassa a hálózati adaptert a készülék bekapcsolásához. Megnyitása 192.168.1.1 egy webböngészőben beállítani a terméket.

Több információ https://wiki.teltonika.lt

[IT] Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità. Aprire 192.168.1.1 in un browser Web per conﬁgurare il prodotto.

Maggiori informazioni in https://wiki.teltonika.lt

[LT] Naudojimosi instrukcija: Prijunkite maitinimo adapterį, įjunkite įrenginį. Interneto naršyklėje atidarykite adresą 192.168.1.1 - galite konﬁgūruoti gaminį.

Daugiau informacijos rasite https://wiki.teltonika.lt

[LV] Lietošanas instrukcija: Pievienojiet Strāvas adapteri, lai ieslēgtu ierīci. Atvērt 192.168.1.1 ar interneta pārlūku, lai konﬁgurētu produktu. Plašāka informācija

https://wiki.teltonika.lt

[NL] Handleiding: Sluit voedingsadapter aan op het apparaat in te schakelen. Open 192.168.1.1 in een webbrowser om het product te conﬁgureren. Meer

informatie in https://wiki.teltonika.lt

[NO] Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne 192.168.1.1 i en nettleser for å konﬁgurere produktet. Mer informasjon på

https://wiki.teltonika.lt

[PL] Instrukcja obsługi: Podłącz adapter zasilania, aby włączyć urządzenie. Otwórz 192.168.1.1 w przeglądarce internetowej, aby skonﬁgurować urządzenie.

Więcej informacji w https://wiki.teltonika.lt

[PT] Manual de instruções: Conecte o adaptador de alimentação para ligar o aparelho. Abra 192.168.1.1 em um navegador da web para conﬁgurar o produto.

Mais informações em https://wiki.teltonika.lt

[RO] Instrucțiuni de utilizare: Conectați adaptorul de alimentare pentru a porni aparatul. Deschide 192.168.1.1 întrun browser web pentru a conﬁgura produsul.

Mai multe informații în https://wiki.teltonika.lt

[SE] Instruktionsmanual: Anslut nätadap tern för att slå på enheten. Öppna 192.168.1.1 i en webbläsare för att konﬁgurera produkten. Mer information på

https://wiki.teltonika.lt

[SI] Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.1.1 v spletnem brskalniku nastaviti izdelek. Več informacij v https://wiki.teltonika.lt

[SK] NávoZd na použitie: Pripojte napájací adaptér k zapnutiu prístroja. Otvorte 192.168.1.1 vo webovom prehliadači pre konﬁguráciu produktu. Viac informácií

nájdete v https://wiki.teltonika.lt

For more information visit www.teltonika.lt

https://teltonika.lt/product/rut950/

https://teltonika.lt/

https://wiki.teltonika.lt/