Krone BA BiG X 780 (BX404-25) Operating instructions
- Type
- Operating instructions
Original operating instructions
Document number: 150000943_11_en
Version: 31/08/2023
BX404-25
Precision forage harvester
BiG X 780
From machine number: 1136331
2
BiG X 780
Original operating instructions 150000943_11_en
Contact
Maschinenfabrik Bernard Krone GmbH & Co. KG
Heinrich-Krone-Straße 10
48480 Spelle
Germany
Telephone main office + 49 (0) 59 77/935-0
Telefax main office + 49 (0) 59 77/935-339
Telefax spare parts warehouse na-
tional territory
+ 49 (0) 59 77/935-239
Telefax spare parts warehouse export + 49 (0) 59 77/935-359
Internet www.landmaschinen.krone.de
https://mediathek.krone.de/
For information on your KRONE machines, also refer to mykrone.green. After you have
registered, you can generate and manage your machines via the machine number so that you
can view the machine data. Via your personal account, you can also access all KRONE
Services.
Technical Information Center (TIC)
Technical and service-relevant information on your KRONE machines can also be found in the
Technical Information Center. All information can be searched using a full-text search, such as
operating instructions, spare parts information, training documents (qualification-based), error
code and parameter descriptions, guided troubleshooting, video tutorials and much more.
3
BiG X 780
Original operating instructions 150000943_11_en
Information for enquiries and orders
Model
Vehicle identification number
Year of manufacture
Contact data of your dealer
Table of contents
4
BiG X 780
Original operating instructions 150000943_11_en
1 Information on This Document...............................................................................................14
1.1 Validity .......................................................................................................................................14
1.2 Significance of the document.....................................................................................................14
1.3 Re-ordering ................................................................................................................................14
1.4 Applicable documents................................................................................................................14
1.5 Target group of this document ...................................................................................................14
1.6 How to use this document..........................................................................................................15
1.6.1 Directories and references.........................................................................................................15
1.6.2 Information on direction .............................................................................................................15
1.6.3 Term “machine”..........................................................................................................................15
1.6.4 Figures .......................................................................................................................................15
1.6.5 Scope of the document ..............................................................................................................15
1.6.6 Means of representation ............................................................................................................15
1.6.7 Conversion table ........................................................................................................................18
2 Safety ........................................................................................................................................20
2.1 Intended use ..............................................................................................................................20
2.2 Reasonably foreseeable misuse................................................................................................20
2.3 Service life of the machine.........................................................................................................21
2.4 Basic safety instructions ............................................................................................................21
2.4.1 Importance of operating instructions..........................................................................................21
2.4.2 Personnel qualification of the operating personnel ....................................................................21
2.4.3 Personnel qualification of the technicians..................................................................................22
2.4.4 Children in danger......................................................................................................................22
2.4.5 Connecting the machine ............................................................................................................22
2.4.6 Structural modifications on the machine ....................................................................................23
2.4.7 Additional equipment and spare parts .......................................................................................23
2.4.8 Jobs on the machine..................................................................................................................23
2.4.9 Operational safety: Technically sound condition........................................................................24
2.4.10 Danger zones.............................................................................................................................25
2.4.11 Ensuring functionality of safety devices .....................................................................................27
2.4.12 Personal protective equipment ..................................................................................................27
2.4.13 Safety sign on the machine........................................................................................................28
2.4.14 Road safety................................................................................................................................28
2.4.15 Parking the machine safely .......................................................................................................29
2.4.16 Consumables .............................................................................................................................29
2.4.17 Chemicals ..................................................................................................................................30
2.4.18 Dangers arising from environment.............................................................................................30
2.4.19 Sources of danger on the machine ............................................................................................32
2.4.20 Dangers in connection with certain activities: climbing up and down ........................................33
2.4.21 Dangers in connection with certain activities: Working on the machine ....................................34
2.4.22 Dangers in connection with certain activities: checking and charging batteries ........................35
2.4.23 Dangers in connection with certain activities: working on wheels and tyres..............................35
2.4.24 Behaviour in dangerous situations and in case of accidents .....................................................36
2.5 Safety routines ...........................................................................................................................36
2.5.1 Shutting down and safeguarding the machine...........................................................................36
2.5.2 Securing raised machine and machine parts against lowering..................................................37
2.5.3 Carrying out oil level check and oil and filter element changes safely.......................................37
2.5.4 Running actuator test.................................................................................................................38
2.6 Safety sign on the machine........................................................................................................38
2.7 Information signs on the machine ..............................................................................................57
2.8 Safety equipment .......................................................................................................................65
2.8.1 SMV emblem .............................................................................................................................67
2.8.2 Fire extinguisher ........................................................................................................................67
3 Data memory ............................................................................................................................69
4 Machine Description................................................................................................................70
4.1 Machine overview ......................................................................................................................70
4.1.1 Contents of the storage compartment........................................................................................71
4.2 Labelling.....................................................................................................................................72
4.3 Lighting ......................................................................................................................................73
Table of contents
BiG X 780
Original operating instructions 150000943_11_en 5
4.3.1 Road travel lighting ....................................................................................................................73
4.3.2 Working lights ............................................................................................................................74
4.3.3 Maintenance lighting ..................................................................................................................75
4.4 Function description chopping crops .........................................................................................76
5 Technical Data..........................................................................................................................78
5.1 Dimensions ................................................................................................................................78
5.2 Weights ......................................................................................................................................78
5.3 Technically permitted maximum speed (road travel) .................................................................78
5.4 Engine data................................................................................................................................79
5.5 Traction drive .............................................................................................................................79
5.6 Electrical system ........................................................................................................................79
5.7 Airborne noise emission.............................................................................................................79
5.8 Ambient temperature .................................................................................................................80
5.9 Vibration values .........................................................................................................................80
5.10 tow coupling ...............................................................................................................................80
5.11 Power supply for headers – power ............................................................................................80
5.12 Power supply for headers – hydraulics ......................................................................................80
5.13 Power supply for headers – electrics .........................................................................................80
5.14 Consumables .............................................................................................................................80
5.14.1 oils..............................................................................................................................................81
5.14.2 Lubricating grease .....................................................................................................................83
5.14.3 Coolant.......................................................................................................................................83
5.14.4 Refrigerant (air conditioning)......................................................................................................83
5.14.5 Fuel ............................................................................................................................................84
5.15 Tyres ..........................................................................................................................................84
5.16 Total weights and axle loads......................................................................................................85
5.17 Released headers......................................................................................................................87
6 Control and Display Elements ................................................................................................88
6.1 Overview of operating elements ................................................................................................88
6.2 Opening doors and windows of cabin .......................................................................................88
6.3 Control and display elements on the steering column ...............................................................91
6.3.1 Steering column switch ..............................................................................................................91
6.3.1.1 Activating horn ...........................................................................................................................91
6.3.1.2 Switching direction indicators on/off...........................................................................................92
6.3.1.3 Switching parking light, dipped beam and work lightings on/off.................................................92
6.3.1.4 Switching full beam on/off ..........................................................................................................94
6.3.1.5 Actuating headlamp flasher .......................................................................................................94
6.3.1.6 Switching windshield wipers on/off ...........................................................................................94
6.3.2 Indicator and warning lamps ......................................................................................................95
6.3.3 Switching the flashing warning light on/off .................................................................................96
6.4 Actuating service brake..............................................................................................................96
6.5 Actuate the trailer brake system (for "trailer brake system" version) .........................................97
6.6 Actuating the momentary foot switches (for "Momentary foot switches in the cabin" version) ..98
6.7 Mirror adjuster............................................................................................................................98
6.8 Setting the anti-collision mirror...................................................................................................99
6.9 Keypad for wiper and warning beacon.....................................................................................100
6.10 Lighting on the cabin ladder and right ladder...........................................................................100
6.11 Interior lighting .........................................................................................................................102
6.12 Operating elements on control lever ........................................................................................102
6.13 Control and display elements on the keypad ...........................................................................106
6.14 Main mode switch ....................................................................................................................108
6.15 Quick-stop switch.....................................................................................................................109
6.16 Navigation module ...................................................................................................................109
6.17 Ignition lock ..............................................................................................................................111
6.18 Additional keypad.....................................................................................................................111
6.19 Sockets ....................................................................................................................................112
6.19.1 Cigarette lighter 12 Volt ...........................................................................................................112
6.19.2 12 V socket/24 V socket ..........................................................................................................113
6.19.3 Diagnostics sockets .................................................................................................................114
6.19.4 In-cab socket............................................................................................................................114
Table of contents
6
BiG X 780
Original operating instructions 150000943_11_en
6.19.5 USB connection .......................................................................................................................114
6.20 Grinding control unit.................................................................................................................115
6.21 Quick-stop switch grinding control unit ....................................................................................116
6.22 Opening and closing side hoods and rear hood ......................................................................117
7 Initial operation ......................................................................................................................119
7.1 Checklist for initial operation ....................................................................................................119
7.2 Mounting warning panels in operating position........................................................................120
7.3 Mounting fire extinguisher........................................................................................................120
7.4 Mounting licence plate .............................................................................................................121
7.5 Connecting side tank to main tank...........................................................................................121
8 Start-up ...................................................................................................................................123
8.1 Check before start-up ..............................................................................................................123
8.2 Setting driver’s seat .................................................................................................................124
8.2.1 Air-cushioned comfort seat ......................................................................................................124
8.2.1.1 Operating air-cushioned comfort seat (for "Standard" version)................................................125
8.2.1.2 Operating air-cushioned comfort seat (for "ACTIVO" version).................................................127
8.2.1.3 Turning the driver's seat (for the "Swivel seat adapter" design) ..............................................131
8.2.2 Steering column adjustment ....................................................................................................131
8.2.3 Setting the terminal ..................................................................................................................132
8.2.4 Monitor for camera monitoring .................................................................................................133
8.2.5 Sun visor ..................................................................................................................................134
8.2.6 Adjustable air nozzles ..............................................................................................................135
8.2.7 Inside rear mirror......................................................................................................................135
8.3 General aspects.......................................................................................................................135
8.3.1 Instructional seat......................................................................................................................135
8.3.2 Cooling box (version with "Insulated thermobox")....................................................................136
8.3.3 Drawer for first-aid kit and operating instructions.....................................................................136
9 Start-up – Grass mode/direct cut header ............................................................................137
9.1 Removing the corn conditioner ................................................................................................138
9.2 Installing the grass channel .....................................................................................................142
9.3 Adjusting the air intake.............................................................................................................143
9.4 Removing round brush from the rotating screen......................................................................144
9.5 Setting Lifting Unit Hydraulics ..................................................................................................144
9.6 Removing grain capture sheet .................................................................................................145
9.7 Disconnecting the side and additional tanks from the main tank .............................................146
9.7.1 Disconnecting the side tank from the main tank ......................................................................146
9.7.2 Disconnecting the additional tank from the main tank .............................................................147
9.8 Removing rear weight ..............................................................................................................147
9.9 Removing spout extension.......................................................................................................149
9.10 Mounting camera in grass mode position (for "EasyLoad auto-loading system" version) .......151
9.11 Dismounting camera in maize mode position (for "EasyLoad auto-loading system" version) .152
9.12 Removing husk comb (version with "Husk comb")...................................................................153
9.12.1 Removing the maintenance flap and deflector sheet...............................................................153
9.12.2 Removing blade support and husk comb.................................................................................155
9.12.3 Removing wear plate ...............................................................................................................156
9.12.4 Mounting wear plate (without window) and deflector sheet .....................................................156
9.12.5 Mounting maintenance flap transfer shaft................................................................................157
10 Start-up – Maize mode...........................................................................................................158
10.1 Removing the grass channel ...................................................................................................159
10.2 Installing the corn conditioner ..................................................................................................160
10.3 Adjusting the air intake.............................................................................................................165
10.4 Pressing round brushes onto the rotating screen ....................................................................166
10.5 Adjusting the lifting unit hydraulics...........................................................................................166
10.6 Mounting grain capture sheet ..................................................................................................167
10.7 Connecting the side and additional tanks from the main tank .................................................167
10.7.1 Connecting the side tank to the main tank...............................................................................168
10.7.2 Connecting the additional tank to the main tank ......................................................................168
10.8 Mounting spout extension ........................................................................................................168
Table of contents
BiG X 780
Original operating instructions 150000943_11_en 7
10.9 Mounting camera in maize mode position (for "EasyLoad auto-loading system" version) ......173
10.10 Dismounting camera in grass mode position (for "EasyLoad auto-loading system" version) ..175
10.11 Attach rear weight ....................................................................................................................176
10.12 Installing husk comb (version with "Husk comb").....................................................................179
10.12.1 Removing the maintenance flap transfer shaft and wear plate................................................179
10.12.2 Mounting wear plate.................................................................................................................181
10.12.3 Mounting husk comb................................................................................................................182
10.12.4 Mounting blade support ...........................................................................................................183
10.12.5 Mounting maintenance flap transfer shaft and deflector sheet ................................................185
11 Commissioning – Grass/maize mode for the transition period.........................................186
12 Start-up – Attaching and removing EasyFlow ....................................................................190
12.1 Mounting EasyFlow..................................................................................................................191
12.1.1 Preparing the intake.................................................................................................................191
12.1.2 Connecting EasyFlow ..............................................................................................................192
12.1.3 Connecting hydraulic hoses.....................................................................................................194
12.1.4 Moving parking jacks on right/left into transport position .........................................................195
12.2 Removing EasyFlow ................................................................................................................195
12.3 Putting Down EasyFlow ...........................................................................................................197
13 Commissioning – Attaching and removing XCollect..........................................................198
13.1 Attaching XCollect....................................................................................................................199
13.1.1 Preparing the intake.................................................................................................................199
13.1.2 Connecting XCollect ................................................................................................................200
13.1.3 Connecting hydraulic hoses.....................................................................................................202
13.1.4 Moving support jacks on right/left into transport position .........................................................203
13.1.5 Enabling additional axle on the terminal ..................................................................................204
13.2 Removing XCollect ..................................................................................................................204
13.3 Parking XCollect ......................................................................................................................207
14 Start-up – Attaching and removing EasyCollect.................................................................208
14.1 Mounting EasyCollect ..............................................................................................................209
14.1.1 Preparing the intake.................................................................................................................209
14.1.2 Connecting EasyCollect...........................................................................................................210
14.1.3 Connecting hydraulic hoses.....................................................................................................212
14.1.4 Moving parking jacks on right/left into transport position .........................................................213
14.2 Removing EasyCollect.............................................................................................................214
14.3 Putting down EasyCollect .......................................................................................................217
15 Start-up – Attaching and removing XDisc ...........................................................................218
15.1 Mounting XDisc........................................................................................................................219
15.1.1 Preparing the intake.................................................................................................................219
15.1.2 Connecting XDisc ....................................................................................................................219
15.1.3 Moving parking jacks on right/left into transport position .........................................................222
15.2 Removing XDisc ......................................................................................................................222
15.3 Putting down XDisc..................................................................................................................224
16 Driving and Transport ...........................................................................................................225
16.1 Preparing the machine for road travel......................................................................................225
16.1.1 Transport position ....................................................................................................................226
16.1.2 Moving header to transport position.........................................................................................226
16.1.3 Moving intake into transport position .......................................................................................229
16.1.4 Swivelling spout into transport position....................................................................................229
16.1.5 Opening the stop cock additional running gear on the XCollect ..............................................230
16.2 Starting engine.........................................................................................................................230
16.2.1 Observing indicator and warning lamps...................................................................................232
16.3 Behaviour after the engine has stalled.....................................................................................233
16.4 Starting up machine .................................................................................................................233
16.4.1 Setting the acceleration behaviour...........................................................................................233
16.4.2 Notes on driving the machine ..................................................................................................234
16.4.3 Driving forwards and stopping .................................................................................................234
16.4.3.1 Cruise control...........................................................................................................................235
Table of contents
8
BiG X 780
Original operating instructions 150000943_11_en
16.4.4 Driving backward and stopping................................................................................................236
16.5 Stopping the machine ..............................................................................................................237
16.5.1 Stopping machine by using control lever .................................................................................237
16.5.2 Stopping machine with the service brake ................................................................................238
16.6 Couple brake pedals (for "trailer brake system" version).........................................................239
16.7 Applying parking brake ............................................................................................................239
16.8 Switching off the engine...........................................................................................................241
16.9 Fitting wheel chocks.................................................................................................................241
16.10 Main battery switch ..................................................................................................................242
16.11 Parking the machine ................................................................................................................242
16.12 Towing the machine.................................................................................................................243
16.12.1 Releasing the parking brake manually.....................................................................................244
16.13 Preparing the machine for shipment ........................................................................................244
16.13.1 Lashing the machine................................................................................................................245
17 Operation device....................................................................................................................246
17.1 Raising and lowering lifting unit ...............................................................................................247
17.2 Aligning pendulum tube horizontally ........................................................................................247
17.3 Releasing header locking.........................................................................................................248
17.4 Trailer operation.......................................................................................................................249
17.4.1 Connecting trailer.....................................................................................................................250
17.4.2 Disconnecting trailer ................................................................................................................251
17.5 Silage additives unit .................................................................................................................252
17.5.1 Internal silage additives unit coarse dosing (for "Controlled silage additives unit" design)......253
17.5.2 Internal silage additives unit fine dosing (for "controlled silage additives unit fine dosing" design)
.................................................................................................................................................260
17.5.3 Connecting an additional silage additives unit (for "External silage additives unit" version)....265
17.6 Field mode on slopes...............................................................................................................266
17.7 Setting inclination-dependent distribution of traction of the traction drive (for "inclination sensor"
version) ....................................................................................................................................266
17.8 Fast change of direction of travel (fast reversing)....................................................................267
17.9 Operating intake/header ..........................................................................................................268
17.10 Lifting unit control.....................................................................................................................270
17.11 Setting spout ...........................................................................................................................273
17.12 Adjusting discharge distance ...................................................................................................273
17.13 TractionControl/Traction control system ..................................................................................274
17.14 Automatic steering system.......................................................................................................275
17.15 Setting chop length ..................................................................................................................277
17.16 Metal detection.........................................................................................................................278
17.17 RockProtect .............................................................................................................................280
17.18 ConstantPower ........................................................................................................................280
17.19 Engine speed management .....................................................................................................281
17.20 AutoScan .................................................................................................................................282
17.21 CropControl..............................................................................................................................283
17.22 PowerSplit................................................................................................................................284
17.23 Contents sensor system ..........................................................................................................286
17.24 Operating VariQuick electrically...............................................................................................289
17.25 Operating VariLOC chop length gearbox.................................................................................289
17.25.1 Switching VariLOC cutting length gearbox ..............................................................................291
17.25.2 VariLOC cutting length gearbox settings on the terminal.........................................................292
17.26 Operating the EasyLoad auto-loading system .........................................................................295
17.26.1 Camera monitor status display ................................................................................................295
17.26.2 Setting EasyLoad auto-loading system....................................................................................297
17.26.3 Activating/deactivating EasyLoad auto-loading system ...........................................................300
17.26.4 Selecting filling strategy ...........................................................................................................300
17.26.5 Filling to rear ............................................................................................................................301
17.27 Operating the cabin lift .............................................................................................................302
17.28 Operating the dirt seal..............................................................................................................303
18 Terminal ..................................................................................................................................305
18.1 Display design..........................................................................................................................305
18.2 Description display...................................................................................................................306
Table of contents
BiG X 780
Original operating instructions 150000943_11_en 9
18.3 Input window ............................................................................................................................306
18.4 Selection window .....................................................................................................................308
19 Terminal machine functions .................................................................................................310
19.1 Status line ................................................................................................................................311
19.2 Malfunctions indicated on malfunction warning panel..............................................................317
19.3 Keys in the title bar ..................................................................................................................318
19.3.1 “Counters” menu ......................................................................................................................319
19.3.2 “Error” menu.............................................................................................................................328
19.3.3 Main menu ...............................................................................................................................332
19.4 Direct input “Field mode”..........................................................................................................332
19.4.1 Temporarily change working width or number of rows ............................................................333
19.4.2 Changing the header speed.....................................................................................................334
19.4.3 Change chop length.................................................................................................................334
19.4.4 Changing the lifting unit control default value ..........................................................................335
19.4.5 Changing Corn Conditioner Roller Distance ............................................................................335
19.5 Information area.......................................................................................................................336
19.6 Engine and driving data display range.....................................................................................336
19.7 Traction drive indicator lights ...................................................................................................340
20 Terminal - Menus ...................................................................................................................343
20.1 Menu structure .........................................................................................................................343
20.2 Bringing up menu level ............................................................................................................353
20.3 Navigating in menus ................................................................................................................354
20.3.1 Changing/saving parameter.....................................................................................................354
20.4 “Diagnostics” menu explanation...............................................................................................354
20.5 "Machine" menu.......................................................................................................................356
20.5.1 "Tanks" menu...........................................................................................................................359
20.5.2 "Cabin lift" menu.......................................................................................................................360
20.5.3 "Electronics" menu...................................................................................................................360
20.5.3.1 "E-Solutions" menu ..................................................................................................................361
20.5.3.2 "Telemetry" menu.....................................................................................................................361
20.5.3.3 "Active errors" menu ................................................................................................................363
20.5.3.4 "Error history" menu.................................................................................................................364
20.5.3.5 "Control units overview" menu .................................................................................................365
20.5.3.6 "Control unit versions" menu....................................................................................................367
20.5.3.7 "Information" menu...................................................................................................................368
20.5.4 "Lighting" menu........................................................................................................................368
20.5.5 "Camera systems" menu..........................................................................................................370
20.5.5.1 "Camera system" menu ...........................................................................................................371
20.5.5.2 "Surround View" menu.............................................................................................................371
20.6 “Cabin” menu ...........................................................................................................................372
20.6.1 “Terminal” menu.......................................................................................................................374
20.6.2 “Armrest” menu ........................................................................................................................375
20.6.3 “Control Lever” menu ...............................................................................................................376
20.6.4 "Interior lighting" menu.............................................................................................................378
20.6.5 “Control Unit Versions” menu...................................................................................................378
20.6.6 “Printer” menu ..........................................................................................................................379
20.6.7 "Automatic climate control" menu ............................................................................................380
20.6.8 "Wiper" menu ...........................................................................................................................382
20.6.9 "Mirror heating" menu ..............................................................................................................382
20.6.10 "Momentary foot switch" menu.................................................................................................383
20.7 "Lubrication" menu...................................................................................................................384
20.7.1 "Central lubrication" menu........................................................................................................385
20.7.2 "Intermediate gearbox" menu...................................................................................................386
20.8 "Crop flow" menu .....................................................................................................................386
20.8.1 “Header” menu.........................................................................................................................390
20.8.2 “Header Drive” menu ...............................................................................................................390
20.8.3 "AutoScan" menu.....................................................................................................................391
20.8.4 “Intake” menu...........................................................................................................................392
20.8.5 "Foreign object detection" menu ..............................................................................................392
20.8.6 “Lifting Unit” menu....................................................................................................................393
Table of contents
10
BiG X 780
Original operating instructions 150000943_11_en
20.8.7 "Grinding device and counterblade" menu...............................................................................395
20.8.8 “Main Coupling” menu..............................................................................................................397
20.8.9 “Corn Conditioner” menu .........................................................................................................399
20.8.10 “Discharge Accelerator” menu .................................................................................................402
20.8.11 "Content material sensor" menu ..............................................................................................403
20.8.12 "CropControl" menu .................................................................................................................404
20.8.13 "Silage additives units" menu...................................................................................................407
20.8.13.1 "External silage additives unit" menu.......................................................................................407
20.8.13.2 "Silage additives unit fine dosing" menu ..................................................................................407
20.8.13.3 "Silage additives unit coarse dosing" menu .............................................................................408
20.9 "Spout" menu ...........................................................................................................................409
20.9.1 "Spout" menu ...........................................................................................................................410
20.9.2 "Auto-loading system" menu....................................................................................................412
20.10 “Engine” menu .........................................................................................................................413
20.10.1 “Diesel Engine” menu ..............................................................................................................414
20.10.2 “ConstantPower” menu ...........................................................................................................415
20.10.3 "Compressed air cleaning" menu.............................................................................................416
20.11 “Hydraulics” menu....................................................................................................................417
20.11.1 “Header Locking” menu ..........................................................................................................418
20.11.2 “Work Hydraulics” menu ..........................................................................................................418
20.11.3 “Auxiliary Hydraulics” menu .....................................................................................................419
20.12 “Drive Functions” menu............................................................................................................419
20.12.1 “Automatic Steering System” menu .........................................................................................420
20.12.2 “Traction Drive” Menu ..............................................................................................................421
20.12.3 “Rear Axle” menu.....................................................................................................................423
20.12.4 "Trailer brake" menu ................................................................................................................424
20.13 “Season Settings” menu ..........................................................................................................425
20.14 "User level" menu.....................................................................................................................426
21 Settings...................................................................................................................................427
21.1 Optimising crop flow.................................................................................................................427
21.2 Optimising discharge capacity of the machine.........................................................................428
21.2.1 Adjusting overhang of chopping blades ...................................................................................428
21.2.2 Setting drum base ...................................................................................................................428
21.2.3 Setting the rear wall discharge accelerator..............................................................................431
21.3 Setting the corn conditioner/grass channel holding-down clamp.............................................435
21.4 Setting deflector sheet on the corn conditioner........................................................................436
22 Maintenance - General Information......................................................................................437
22.1 Observe the service record booklet .........................................................................................437
22.2 Maintenance table....................................................................................................................438
22.2.1 Maintenance – Before the season ...........................................................................................438
22.2.2 Maintenance – After the season ..............................................................................................439
22.2.3 Maintenance – Once after 1 hour ............................................................................................440
22.2.4 Maintenance – Once after 10 hours.........................................................................................441
22.2.5 Maintenance – 6 times after every 10 hours............................................................................441
22.2.6 Maintenance – Once after 50 hours.........................................................................................441
22.2.7 Maintenance – Once after 200 hours.......................................................................................442
22.2.8 Maintenance – Once after 500 hours.......................................................................................442
22.2.9 Maintenance – Once after 1000 km.........................................................................................442
22.2.10 Maintenance – At the beginning of the cold season ................................................................442
22.2.11 Maintenance – Every 10 hours, at least daily ..........................................................................442
22.2.12 Maintenance – Weekly.............................................................................................................444
22.2.13 Maintenance – Every 30 hours ................................................................................................444
22.2.14 Maintenance – Every 50 hours ................................................................................................444
22.2.15 Maintenance – Every 100 hours ..............................................................................................445
22.2.16 Maintenance – Monthly............................................................................................................445
22.2.17 Maintenance – Every 250 hours ..............................................................................................445
22.2.18 Maintenance – Every 500 hours ..............................................................................................446
22.2.19 Maintenance – Every 1,000 hours, at least after the season...................................................447
22.2.20 Maintenance - Every 1000 hours, at least every 2 years.........................................................448
22.2.21 Maintenance – Every 2,000 hours, at least once a year..........................................................448
Table of contents
BiG X 780
Original operating instructions 150000943_11_en 11
22.2.22 Maintenance – Every 3 years ..................................................................................................448
22.2.23 Maintenance – Every 4,000 hours, at least every four years...................................................449
22.2.24 Maintenance – As needed .......................................................................................................449
22.3 Tightening torques ...................................................................................................................450
22.4 Cleaning the machine ..............................................................................................................453
22.5 Compressed air connections to clean with compressed air.....................................................454
22.6 Swivel the ladder to the cabin to the side ................................................................................455
22.7 Securing cabin lift.....................................................................................................................456
23 Maintenance - Engine ............................................................................................................458
23.1 Overview of engine ..................................................................................................................458
23.2 Dirt deposits in engine compartment .......................................................................................459
23.2.1 Cleaning engine compartment with compressed air ................................................................459
23.3 Engine oil level.........................................................................................................................459
23.3.1 Checking engine oil level ........................................................................................................460
23.3.2 Topping up engine oil...............................................................................................................460
23.4 Cleaning fuel tank ....................................................................................................................461
23.5 Fuel prefilter/water separator ...................................................................................................462
23.5.1 Changing the fuel filter element ...............................................................................................462
23.5.2 Draining condensation water out of the fuel prefilter................................................................462
23.6 Refuelling .................................................................................................................................463
23.7 Venting the fuel prefilter/water separator .................................................................................464
23.8 Vent the diesel engine fuel system ..........................................................................................465
23.9 Engine coolant .........................................................................................................................465
23.10 Checking the engine coolant level ...........................................................................................466
23.11 Checking engine piping............................................................................................................468
23.11.1 Checking pipework in the air conditioning and heating system ...............................................468
23.11.2 Checking tubing in engine cooling system...............................................................................469
23.11.3 Checking pipework in air intake and charge air .......................................................................470
23.11.4 Checking fuel lines...................................................................................................................470
23.12 Cleaning air filter ......................................................................................................................471
23.13 Replacing safety cartridge .......................................................................................................472
23.14 Shutting down the diesel engine ..............................................................................................472
24 Maintenance – Compressed Air System..............................................................................474
24.1 Drain condensation water from the compressed air tank.........................................................474
24.2 Retighten tensioning straps at the compressed air tank ..........................................................475
25 Maintenance – Basic Machine ..............................................................................................476
25.1 Cleaning the windows and outside rear-view mirrors of the cabin...........................................476
25.2 Checking/refilling windscreen washer system .........................................................................477
25.3 Maintaining air conditioning and heating..................................................................................478
25.3.1 Components of air conditioning ...............................................................................................478
25.3.2 Replacing/cleaning fresh air filter.............................................................................................479
25.3.3 Replacing/cleaning circulation filter..........................................................................................479
25.4 Cleaning cooler and cooler compartment ................................................................................480
25.5 Draining coolant .......................................................................................................................481
25.6 Maintaining chassis..................................................................................................................482
25.6.1 Checking attachment of steering cylinder ................................................................................482
25.6.2 Checking fitting of track rod .....................................................................................................482
25.6.3 Checking the hub cover of the rear axle, with front wheel drive version..................................483
25.6.4 Checking the hub bearing of the rear axle, for the front-wheel drive version...........................483
25.6.5 Checking attachment of wheel hub gearbox............................................................................484
25.7 Maintaining brake (Bosch) .......................................................................................................485
25.8 Maintaining belt drives ............................................................................................................486
25.8.1 Checking kraftband ..................................................................................................................486
25.8.2 Checking pulley........................................................................................................................487
25.9 Maintaining tyres and wheels...................................................................................................487
25.9.1 Checking/maintaining tyres......................................................................................................487
25.9.2 Retighten wheel nuts ...............................................................................................................488
25.9.3 Running direction of tyres ........................................................................................................488
25.9.4 Changing tyre size ...................................................................................................................488
Table of contents
12
BiG X 780
Original operating instructions 150000943_11_en
25.10 Maintaining tow coupling..........................................................................................................489
25.11 Checking the fire extinguisher..................................................................................................490
25.12 Checking gap dimensions between rear and side hoods ........................................................490
26 Maintenance – Feed System .................................................................................................492
26.1 Removing intake unit with mounting cart .................................................................................492
26.2 Mounting intake unit with installation cart ................................................................................495
26.3 Removing intake unit with header............................................................................................497
26.4 Mounting intake unit with header .............................................................................................499
26.5 Grinding chopping blades ........................................................................................................501
26.5.1 Grinding the chopping blades when intake is not mounted .....................................................503
26.5.2 Cleaning the grinding channel .................................................................................................503
26.5.3 Performing grinding process ....................................................................................................504
26.5.4 Readjusting the counterblade ..................................................................................................506
26.5.5 Grinding and readjusting counterblade (for the version with "automatisch counterblade
adjustment") .............................................................................................................................508
26.6 Adjusting or replacing the grinding stone.................................................................................510
26.6.1 Setting the grinding stone ........................................................................................................510
26.6.2 Checking the number of remaining grinding cycles .................................................................513
26.6.3 Replacing the grinding stone ...................................................................................................513
26.7 Readjusting or changing chopping blades ...............................................................................518
26.8 Working with half the number of chopping blades ...................................................................533
26.9 Turning or replacing counterblade ...........................................................................................534
26.10 Operating the mounting cart of the chopper unit (for "Chopper unit mounting cart" design) ...536
26.10.1 Setting mounting cart ...............................................................................................................536
26.10.2 Parking mounting cart ..............................................................................................................537
26.11 Turning or replacing conveyor bars of pre-compression roller.................................................537
26.12 Changing conveyor bars on feed roller ....................................................................................538
26.13 Adjusting the gap between the scraper and flat roller..............................................................538
26.14 Adjusting the gap between the compression roller and scraper ..............................................541
26.15 Setting the springs on the intake unit.......................................................................................542
27 Maintenance - Crop Flow.......................................................................................................544
27.1 Access points to crop flow .......................................................................................................544
27.1.1 Removing the grass channel ...................................................................................................545
27.1.2 Installing the grass channel .....................................................................................................545
27.1.3 Opening maintenance flap transfer shaft .................................................................................545
27.1.4 Removing drum base and grating base (version with "Grating base").....................................546
27.1.5 Mounting drum base and grating base (version with "Grating base")......................................548
27.1.6 Removing the rear wall of the discharge accelerator...............................................................549
27.1.7 Reinstalling the rear wall of the discharge accelerator ............................................................550
27.1.8 Removing maintenance flap in channel support ......................................................................550
27.1.9 Opening maintenance flap in the spout ...................................................................................551
27.2 Maintaining the corn conditioner ..............................................................................................552
27.2.1 Lubricating the deflection roll of the corn conditioner belt after washing .................................552
27.2.2 Check the corn conditioner with rollers for wear and tear........................................................553
27.3 Maintenance discharge accelerator .........................................................................................554
27.3.1 Cleaning the bearing of the discharge accelerator ..................................................................554
27.3.2 Checking discharge scoops ....................................................................................................555
27.3.3 Removing/installing discharge scoops.....................................................................................555
27.3.4 Checking and adjusting discharge accelerator scraper ...........................................................556
27.4 Setting corn conditioner ...........................................................................................................557
27.5 Maintenance husk comb (version with "Husk comb") ..............................................................560
28 Maintenance - Hydraulic System..........................................................................................563
28.1 Pressure limiting valves ...........................................................................................................563
28.2 Hydraulic oil .............................................................................................................................564
28.3 Maintaining hydraulic oil tank...................................................................................................564
28.4 Changing the high-pressure filter.............................................................................................565
28.5 Checking hydraulic hoses ........................................................................................................566
29 Maintenance - Gearbox .........................................................................................................567
Table of contents
BiG X 780
Original operating instructions 150000943_11_en 13
29.1 Overview of gearboxes ............................................................................................................567
29.2 Servicing the main gearbox .....................................................................................................567
29.3 Servicing the transfer gearbox .................................................................................................570
29.4 Maintaining intermediate gearbox intake .................................................................................571
29.5 Maintaining bottom roller gearbox............................................................................................572
29.6 Maintaining top roller gearbox..................................................................................................573
29.7 Maintaining wheel hub gearbox ...............................................................................................574
29.8 Maintaining spout rotary drive gearbox....................................................................................576
29.9 Servicing VariLOC chop length gearbox..................................................................................577
30 Maintenance – Electrics ........................................................................................................580
30.1 Batteries...................................................................................................................................581
30.1.1 Cleaning and maintaining batteries..........................................................................................582
30.1.2 Charging batteries....................................................................................................................582
30.1.3 Replacing batteries .................................................................................................................583
30.2 Maintaining alternator ..............................................................................................................585
30.3 Maintaining starter ...................................................................................................................586
31 Maintenance - Lubrication ....................................................................................................587
31.1 Lubricating universal shafts .....................................................................................................587
31.1.1 Lubricating the universal shaft drive intake..............................................................................588
31.1.2 Lubricating the universal shaft upper roller gearbox ................................................................588
31.1.3 Lubricating universal shaft header ...........................................................................................589
31.1.4 Lubricating the double joint ......................................................................................................590
31.1.5 Lubricating universal joints on the transfer gearbox ................................................................590
31.2 Lubrication chart - machine......................................................................................................590
32 Maintenance – Central Lubrication System .......................................................................598
32.1 Distributor blocks of the central lubrication unit .......................................................................598
32.2 Lubricants ................................................................................................................................603
32.3 Filling the lubricant tank ...........................................................................................................603
32.4 Check filling level .....................................................................................................................604
32.5 Starting intermediate lubrication ..............................................................................................605
33 Malfunction, cause and remedy ...........................................................................................606
33.1 Electrics/electronics BiG X defective .......................................................................................606
33.1.1 Cable break, short circuit .........................................................................................................606
33.1.2 Overview of fuses ....................................................................................................................608
33.1.3 Overview of control units..........................................................................................................611
33.1.4 Overview of sensors ................................................................................................................612
33.1.5 Overview actuators ..................................................................................................................613
33.2 Malfunctions in the central lubrication unit ...............................................................................615
33.2.1 Searching for the error in the central lubrication system..........................................................615
33.3 External starting of the machine ..............................................................................................615
33.4 Removing crop blockages........................................................................................................617
33.4.1 Bringing the machine into a safe state.....................................................................................618
33.4.2 Reversing intake/header ..........................................................................................................618
33.4.3 Removing crop blockages from the crop flow ..........................................................................620
33.4.3.1 Removing crop blockages in the area of the transfer shaft......................................................620
33.4.3.2 Removing crop blockages between the chopping drum and the discharge accelerator..........621
33.4.3.3 Removing crop blockage in the area of the discharge accelerator ..........................................624
33.4.3.4 Removing crop blockage above the channel support/in the spout ..........................................625
33.4.3.5 Removing crop blockage in the chopper unit...........................................................................626
33.5 Car jack contact points.............................................................................................................628
34 Waste disposal.......................................................................................................................630
35 Index........................................................................................................................................631
36 Declaration of conformity .....................................................................................................645
1 Information on This Document
1.1 Validity
14
BiG X 780
Original operating instructions 150000943_11_en
1 Information on This Document
1.1 Validity
This document is valid for machines of type:
BX404-25 (BiG X 780)
All information, illustrations and technical data in this document correspond to the latest state at
the time of publication.
We reserve the right to make design changes at any time and without notification of reasons.
1.2 Significance of the document
This is an important document. It is addressed to the user and contains safety-relevant
information.
Prior to starting work, read the complete document and observe its contents.
Keep this document ready to hand for the user of the machine.
Hand over this document to subsequent users.
1.3 Re-ordering
You can request a replacement document if this document became completely or partly
unusable, or if you need it in a different language. Please specify the document number shown
on the cover page in your order. Alternatively, you can download the document online from
KRONE MEDIA https://media.mykrone.green.
1.4 Applicable documents
To ensure that the machine is used safely and as intended, observe the following further
applicable documents.
• Operating instructions for diesel engine, Liebherr Machines Bulle S.A.
• Supplement to operating instructions "Error messages, information messages and
parameters"
• Operating instructions for header, KRONE
• Operating instructions for transport wagon, KRONE
• KRONE NIR Control dual operating instructions
• Operating instructions for universal shaft
• Circuit diagram, KRONE
• Spare parts list, KRONE
• Service record booklet, KRONE
1.5 Target group of this document
This document aims at the operator of the machine who fulfills the minimum requirements of
personnel qualification,see Page21.
Information on This Document 1
How to use this document 1.6
BiG X 780
Original operating instructions 150000943_11_en 15
1.6 How to use this document
1.6.1 Directories and references
Contents/headers
The contents and headers in this document ensure quick orientation in the chapters.
Index
The index contains catchwords in alphabetical order which enable to find information on a
desired topic easily. The index can be found on the last pages of this document.
Cross references
Cross references to another place in the document or to another document are in the text with
page number.
Examples:
• Check the tight seat of all screws on the machine, see Page15. (INFO: If you use an
electronic version of this document, click on the link to go to the specified page.)
• For further information, refer to the operating instructions of the universal shaft
manufacturer.
1.6.2 Information on direction
Directional information in this document, such as front, rear, right and left, applies in the
direction of travel of the machine.
1.6.3 Term “machine”
Throughout the rest of this document, the “exact forage harvester” will also be referred to as the
“machine”.
1.6.4 Figures
The figures in this document do not always represent the exact machine type. The information
that refers to the figure always corresponds to the machine type of this document.
1.6.5 Scope of the document
In addition to standard equipment, accessories kits and versions of the machine are described
in this document. Your machine may deviate from this document.
1.6.6 Means of representation
Icons in the text
The following means of representation (icons) are used to present the text more clearly:
1 Information on This Document
1.6 How to use this document
16
BiG X 780
Original operating instructions 150000943_11_en
This arrow characterizes an action step. Several arrows in a row identify a sequence of
actions to be performed step by step.
This icon identifies a prerequisite that has to be fulfilled to perform an action step or a
sequence of actions.
This arrow marks the intermediate result of an action step.
This arrow identifies the result of an action step or sequence of actions.
This bullet point identifies an enumeration. If the bullet point is intended, it identifies the
second level of the enumeration.
Icons in figures
The following icons can be used in illustrations:
Icon Explanation Icon Explanation
1
Reference sign for part
I
Position of a part (e.g. move from
position I to position II)
X
Dimensions (e. g. also W = width,
H = height, L = length)
Magnification of display detail
LH
Left side of machine
RH
Right side of machine
Direction of travel Direction of motion
Reference line for visible material Reference line for covered mater-
ial
Centre line Cable routes
Open Closed
Apply liquid lubricant (e.g. lubric-
ating oil)
Apply lubricating grease
Warning signs
Warnings of dangers are separated from the remaining text as warning signs and are identified
with a danger sign and signal words.
The warning signs must be read and the measures must be observed in order to prevent
personal injury.
Explanation of danger sign
This is the danger sign that warns of a risk of injury.
Please observe all notes marked with the danger sign in order to avoid injuries or death.
Information on This Document 1
How to use this document 1.6
BiG X 780
Original operating instructions 150000943_11_en 17
Explanation of signal words
DANGER
The signal word DANGER warns of a hazardous situation which will result in serious injuries
or death if the warning sign is ignored.
WARNING
The signal word WARNING warns of a hazardous situation which will result in serious injuries
or death if the warning sign is ignored.
CAUTION
The signal word CAUTION warns of a hazardous situation which will result in minor to
moderate injuries if the warning sign is ignored.
Example of a warning sign:
WARNING
Eye damage caused by flying dirt particles
When cleaning with compressed air, dirt particles are ejected at high speed and could get into
the eyes. Therefore eyes could be hurt.
Keep people away from the working area.
Wear personal protective equipment when performing cleaning work with compressed air
(e.g. eye protection).
Warnings of property damage/environmental damage
Warnings of property/environmental damage are separated from the remaining text and marked
with "Notice".
Example:
NOTICE
Gearbox damage due to low oil level
The gearboxes could be damaged when the oil level is too low.
Check gear oil level at regular intervals and top up oil, if necessary.
Check gear oil level approx. 3 to 4 hours after the machine has been switched off. Check
oil level only when machine is in horizontal position.
Notices with information and recommendations
Additional information and recommendations for trouble-free and productive operation of the
machine are separated from the remaining text and marked with “Information”.
Example:
INFO
Each safety sign is provided with an order number and can be ordered directly from the
manufacturer or from an authorised specialist dealer.
1 Information on This Document
1.6 How to use this document
18
BiG X 780
Original operating instructions 150000943_11_en
1.6.7 Conversion table
The following table can be used to convert metric units into US units.
Size SI units (metric) Factor Inch-pound units
Unit name Abbrevi-
ation
Unit name Abbrevi-
ation
Area Hectare ha 2.47105 Acre acres
Volume flow Litres per minute L/min 0.2642 US gallons per
minute
gpm
Cubic metres
per hour
m³/h 4.4029
Force Newton N 0.2248 Pound force lbf
Length Millimetre mm 0.03937 Inch in.
Metre m 3.2808 Foot ft.
Power Kilowatt kW 1.3410 Horsepower hp
Pressure Kilopascal kPa 0.1450 Pounds per
square inch
psi
Megapascal MPa 145.0377
bar (non-SI) bar 14.5038
Torque Newtonmeter Nm 0.7376 pound-foot or
foot-pound
ft∙lbf
8.8507 pound-inch or
inch-pound
in∙lbf
Temperature Degrees Celsius °C °Cx1.8+32 Degrees
Fahrenheit
°F
Velocity Metres per
minute
m/min 3.2808 Feet per minute ft/min
Metres per
second
m/s 3.2808 Feet per second ft/s
Kilometres per
hour
km/h 0.6215 Miles per hour mph
Volumes Litres L 0.2642 US gallon US gal.
Millilitre ml 0.0338 US ounce US oz.
Cubic centi-
metre
cm³ 0.0610 Cubic inch in³
Weight Kilogram kg 2.2046 Pound lbs
Information on This Document 1
How to use this document 1.6
BiG X 780
Original operating instructions 150000943_11_en 19
This page has been left blank deliberately.
2 Safety
2.1 Intended use
20
BiG X 780
Original operating instructions 150000943_11_en
2 Safety
2.1 Intended use
This machine is a self-propelled forage harvester and is used to chop crops.
The crops designated for the intended use of this machine in conjunction with
• a KRONE XCollect are harvested thick-stemmed forage plants, e.g. maize plants,
• a KRONE EasyCollect are harvested thick-stemmed forage plants, e.g. maize plants,
• a KRONE XDisc are mown stalk and leaf crops,
• a KRONE EasyFlow collected stalk and leaf crops,
• a header for smallwood crops from cut groves.
The machine is designed exclusively for use in agriculture and may only be used when
• all safety devices are available according to the operating instructions and are located in the
protective position.
• all safety instructions of the operating instructions have been observed and complied with,
both in chapter “Basic safety instructions”, see Page21, and directly in the chapters of the
operating instructions.
The machine may be used only by people who satisfy the personnel qualification requirements
designated by the machine manufacturer, see Page21.
These operating instructions are part of the machine and must therefore be at hand when the
machine is in use. The machine may be operated only when the operator has received training
and in compliance with these operating instructions.
If the machine is used for applications which are not described in these operating instructions,
this may result in serious injuries or death and damage to the machine and other property.
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
the proper operation. For this reason, unauthorised modifications shall exclude any liability of
the manufacturer for consequential damage.
The intended use shall also include the adherence to the operating, maintenance and repair
conditions set by the manufacturer.
2.2 Reasonably foreseeable misuse
Any use beyond the intended usesee Page20 is regarded as improper use and is therefore
misuse according to the Machinery Directive. The manufacturer is not liable for damage
resulting from this, the user alone bears the risk.
Such misuse is for example:
• Processing of crops which are outside the intended use of the machine,see Page20
• Transport of people
• Transport of goods
• Exceeding the permitted technical gross weight
• Non-compliance with the safety labels on the machine and safety notes in the operating
instructions
• Performing troubleshooting, setting, cleaning, repair and maintenance work contrary to the
information in the operating instructions
• Unauthorised modifications to the machine
• Attachment of unauthorised or unapproved additional equipment
• Use of spare parts which are not KRONE original spare parts
• Stationary operation of the machine
Unauthorised modifications to the machine may affect the properties of the machine or disrupt
proper operation. For this reason, unauthorised modifications will exclude any liability of the
manufacturer for consequential damage.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
-
355
-
356
-
357
-
358
-
359
-
360
-
361
-
362
-
363
-
364
-
365
-
366
-
367
-
368
-
369
-
370
-
371
-
372
-
373
-
374
-
375
-
376
-
377
-
378
-
379
-
380
-
381
-
382
-
383
-
384
-
385
-
386
-
387
-
388
-
389
-
390
-
391
-
392
-
393
-
394
-
395
-
396
-
397
-
398
-
399
-
400
-
401
-
402
-
403
-
404
-
405
-
406
-
407
-
408
-
409
-
410
-
411
-
412
-
413
-
414
-
415
-
416
-
417
-
418
-
419
-
420
-
421
-
422
-
423
-
424
-
425
-
426
-
427
-
428
-
429
-
430
-
431
-
432
-
433
-
434
-
435
-
436
-
437
-
438
-
439
-
440
-
441
-
442
-
443
-
444
-
445
-
446
-
447
-
448
-
449
-
450
-
451
-
452
-
453
-
454
-
455
-
456
-
457
-
458
-
459
-
460
-
461
-
462
-
463
-
464
-
465
-
466
-
467
-
468
-
469
-
470
-
471
-
472
-
473
-
474
-
475
-
476
-
477
-
478
-
479
-
480
-
481
-
482
-
483
-
484
-
485
-
486
-
487
-
488
-
489
-
490
-
491
-
492
-
493
-
494
-
495
-
496
-
497
-
498
-
499
-
500
-
501
-
502
-
503
-
504
-
505
-
506
-
507
-
508
-
509
-
510
-
511
-
512
-
513
-
514
-
515
-
516
-
517
-
518
-
519
-
520
-
521
-
522
-
523
-
524
-
525
-
526
-
527
-
528
-
529
-
530
-
531
-
532
-
533
-
534
-
535
-
536
-
537
-
538
-
539
-
540
-
541
-
542
-
543
-
544
-
545
-
546
-
547
-
548
-
549
-
550
-
551
-
552
-
553
-
554
-
555
-
556
-
557
-
558
-
559
-
560
-
561
-
562
-
563
-
564
-
565
-
566
-
567
-
568
-
569
-
570
-
571
-
572
-
573
-
574
-
575
-
576
-
577
-
578
-
579
-
580
-
581
-
582
-
583
-
584
-
585
-
586
-
587
-
588
-
589
-
590
-
591
-
592
-
593
-
594
-
595
-
596
-
597
-
598
-
599
-
600
-
601
-
602
-
603
-
604
-
605
-
606
-
607
-
608
-
609
-
610
-
611
-
612
-
613
-
614
-
615
-
616
-
617
-
618
-
619
-
620
-
621
-
622
-
623
-
624
-
625
-
626
-
627
-
628
-
629
-
630
-
631
-
632
-
633
-
634
-
635
-
636
-
637
-
638
-
639
-
640
-
641
-
642
-
643
-
644
-
645
-
646
Krone BA BiG X 780 (BX404-25) Operating instructions
- Type
- Operating instructions
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Krone BA BiG X 630 Stufe 3 (BX201-45) Operating instructions
-
-
-
-
-
-
-
-
-
Other documents
-
Avteq ELT-2100 User guide
-
Wanderer 599462 User guide
-
OXO B0002YTFU0 User manual
-
Harvest TEC 476 Owner's manual
-
LORD W1 User manual
-
Tsubaki TKUA Series User manual
-
Howard Miller 495655 Operating instructions
-
Pottinger MEX OK Operating instructions
-
Tohnichi AFC-20G2 Owner's manual
-
Support TF User manual
