Inverto IDLV-3000P User manual

IDLV-3000P

Professional Integrated Receiver/Decoder

En

Professional

Integrated

Receiver/Decoder

User Manual

IDLV-3000P

En

1

Table of Contents

Notices 2

Before using the device 3

Overview 4

Main Features 4

Unpacking 5

Control panel and interfaces 5

Basic Functions 10

Menu Operations 12

ASI Input / Output and CI descramble function 27

Trouble Shooting 29

Specications 30

Safety 32

Warrenty, service and support 33

2

Not to be copied, used or translated in part or whole without Inverto prior consent in writing except approval of

ownership of copyright and copyright law.

WARRANTY

This warranty does not cover parts which may become defective due to misuse of the information contained in

this manual.

Read this manual carefully and make sure you understand the instructions provided. For your safety, be aware of

the following precautions.

WARNING! IMPORTANT SAFETY INSTRUCTIONS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

WARNING

To• reducetheriskofreorelectricshock,donotexposethisapparatustorainormoisture.

Toavoidexplosiondanger,donotdisposeofbatteriesinanopenre.•

CE MARK FOR EUROPEAN HARMONISED STANDARDS

The CE mark which is attached to these products means it conforms to EMC Directive (89/336/EEC) and

Low Voltage Directive (73/23/EEC).

IMPORTANT INFORMATION

Sh• ould you experience a problem with this unit, please refer to the trouble shooting section of this user

manual.

Please retain the original packaging, should it be necessary at some stage to return the unit.•

Disposal of Old Electrical and Electronic Equipment (Applicable in the European Union and other European

countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste.

Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic

equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences

for the environment and human health, which could otherwise be caused by inappropriate waste handling of this

product. The recycling of materials will help to conserve natural resources. For more detailed information about

recyclingofthisproduct,pleasecontactyourlocalCivicOfce,yourhouseholdwastedisposalservice,ortheshop

where you purchased the product.

COPYRIGHTS

Television programmes, movies, video tapes, discs, and other materials may be copyrighted. Unauthorized

recording of copyrighted material may be against the copyright laws in your region. Also, use of this product with

cable television transmissions may require authorization from the cable television operator or transmitter/owner.

VENTILATION

Do not expose the product to high temperatures, such as placing it on top of other product that produce •

heat or in places exposed to direct sunlight or spot lights.

Theventilationslotsontopoftheproductmustbeleftuncoveredtoallowproperairowintotheunit.•

Do not stand the product on soft furnishings or carpets. •

Do not stack electronic equipments on top of the product.•

Do not place the product in a location subject to extreme changes in temperature. The temperature •

gradient should be less than 10 degrees C/hour.

Place the product in a location with adequate ventilation to prevent the build-up of heat inside the product. •

The minimum ventilation space around the unit should be 7 cm. The ventilation should not be impeded by

covering the ventilation openings with items, such as newspapers, table cloth, curtains, etc.

POWER SOURCES

The product is not disconnected from the AC power source (mains) as long as it is connected to the power •

outlet or wall socket, even if the product is turned off.

If the product will not be used for a long period of time, disconnect it from the AC power outlet or wall socket.•

Notices

En

3

Before Using the device

Thank you for purchasing the IDLV-3000P Professional Integrated Receiver Decoder. This User Manual is written

for operators/users of the IDLV-3000P to assist in installation and operation. Please read this user manual carefully

before installation and use of the device.

FOR YOUR SAFETY

This equipment is provided with a protective earthing ground incorporated in the power cord. The main plug shall

only be inserted in a socket outlet provided with a protective earth contact. Any interruption of the protective

conductor, inside or outside the device, is likely to make the device dangerous. Do not remove the covers of this

equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed.

Only Inverto trained and approved service engineers are permitted to service this equipment.

The supplied AC power cable must be used to power the device. If the power cord becomes damaged it must be

replaced. No operator serviceable parts inside. Refer servicing to Inverto trained and approved service engineers.

For the correct and safe use of the device, it is essential that both operating and servicing personnel follow

generallyacceptedsafetyproceduresinadditiontothesafetyprecautionsspeciedinthismanual.Wheneverit

is likely that safety protection is impaired, the device must be made in-operative and secured against unintended

operation. The appropriate servicing authority must be informed. For example, safety is likely to be impaired if the

device fails to perform the intended measurements or shows visible damage.

WARNINGS

The mounting environment should be relatively dust free, free of excessive vibration and the ambient •

temperature between 0C° to 40C°. Relative humidity of 20% to 80% (non-condensed) is recommended.

Avoid direct contact with water.•

Never place the equipment in direct sunlight.•

The outside of the equipment may be cleaned using a lightly dampened cloth. Do not use any cleaning •

liquids containing alcohol, methylated spirit or ammonia etc.

Forcontinuedprotectionagainstrehazard,replacelinefusedonlywithsametype.•

Airintakeforcoolingisachievedviaholesatthesideofthedeviceandthefansinside.Theairowshould•

notbeobstructed.Therefore,thedevicehastobeplacedonaatsurface,leavingsomespaceatthe

sides of the device.

When in operation, the internal temperature should not exceed the limit of 70C°.•

4

Overview

The IDLV-3000P is a professional digital receiver decoder platform with CI interface. IDLV-3000P can receive

digital satellite TV (DVB-S), cable TV (DVB-C) or terrestrial TV (DVB-T) signal. The IDLV-3000P platform

contains the following series:

IDLV-3000P-10 series provides two CI slots, A/V outputs without ASI output;•

IDLV-3000P-18 series decodes free-to-air TV and provides A/V and ASI outputs;•

IDLV-3000P-20 series provides two CI slots, A/V and ASI output;•

IDLV-3000P-30 series provides two CI slots, A/V outputs, ASI output and ASI input interface. •

The following table summarizes the main functionalities and availability for the different series:

Function

Model

Input Signal

DVB-S DVB-C DVB-T

A V C I ASI OUT ASI IN BNC Video

3000P-10 series ●●● ● ● ○ ○ ●

3000P-18 series ●●● ● ○ ● ○ ●

3000P-20 series ●●● ● ● ● ○ ●

3000P-30 series ●●● ● ● ● ● ●

Notes:“●”showsthatthefunctionisavailable;“○”showsthatthefunctionisnotavailable.

Main Features

Fully compliant with MPEG-2 and DVB standards•

2 Common Interface slots (PCMCIA) supporting CAMs of Irdeto, Viaccess, NDS and others•

Multi-program descrambling, depending on the CI module (available on -10/ -20/ -30 series)•

ASI input, the un-decrypted programs could be further decrypted through loop through (available on IDLV-•

3000P-30 series only)

Support professional analog video/audio interface outputs•

User-friendly OSD and easy-to-use menus •

User programmable satellite & transponder information (on IDLV-3000P-xxS models)•

Auto network search for newly added transponders/networks (on IDLV-3000P-xxS models)•

Storing up to 2000 channels•

SCPC/MCPC reception from C/Ku band satellites (available on IDLV-3000P-xxS models)•

VBI Teletext support•

Antenna positioning help feature (available on IDLV-3000P-xxS models)•

Automatic PAL/NTSC conversion•

Auto storing last channel tuned•

En

5

Unpacking

Please unpack the box to check all of the following items are included in the packaging:

User’s manual 1pc

IDLV-3000P 1pc

Power cord 1pc

AV cable with three cores 1pc

ASI cable 1pc (with IDLV-3000P-20/ -30 series)

XLR connector 2pcs (with IDLV-3000P-30 series)

Control Panels and Interfaces

FRONT PANEL

Menu Esc Shift

Ok

Audio R/L Info TV/R

Common Interface

Po werLock Shift

IDL V -3000P Professional MPEG-2 DVB Integrated Receiver Decoder

A1 A2 A3 A4 A5 A6-A9 A10

A11

A12

B13

A1 Power Power indicator, it is on when the power supply works

A2 Lock Satellite signal indicator, it is on when the satellite signal or ASI input signal

are received and locked

A3 SHIFT Shift indicator, when it is on, the keys of A6~A9 operates with their alternative

function

A4 4x 7-segment LED Display current channel No. and information, when IRD starts, it display as

boot & - - - - In general, the LED displays the channel number from 0 ~ 2000,

when you are tuning the volume it will display from 0 ~ 17, if you are checking

the channel information, the LED will display the BER value from 0.00 – 10.00

A5 Common Interface 2 PCMCIA Module slot

A6~A9 ▲▼◄►  Thesekeysareusedtosetorselecttheparametersofdifferentfunctions,

    pleaserefertothetablebelowfordetaileddenitionofA6~A9:

Key Viewing mode

SHIFT is off SHIFT is on

Menu mode

▲/Up Change to last channel Select audio language Cursor moves up

▼/Down Change to next channel Select audio channel Cursor moves down

◄/Left Decrease volume Display channel information Modify parameter/ Cursor

moves left

►/Right Increase volume TV/Radio switch Modify parameter/ Cursor

moves right

6

A10 OK  ConrmationKey,itisusedtoentersubmenuorconrmoperation/selection.

A11 MENU The Menu key is used to display menu and command box

A12 ESC The Exit key is used to return to last level menu or exit menu

A13 SHIFT Alternative function key, press the SHIFT key for 2 seconds, SHIFT indicator

will be on, then A6~A9 will operate in alternative function mode, please refer to

the table above. When SHIFT is on, the IRD can be operated through remote

control (optional, not supplied).

REAR PANEL

B2 B4

B3 B10 B11

B7

B5 B8 B9 B12 B13 B14B1

B6

B15

B1 GND Connect to ground

B2 XLR L XLR interface, left audio channel balance output

B3 XLR R XLR interface, right audio channel balance output

B4 VIDEO RCA interface, AV video output

B5 AUDIO L RCA interface, left audio channel output

B6 AUDIO R RCA interface, right audio channel output

B7 VIDEO BNC interface, multiplex video output

B8 ASI OUT1 ASI output interface

B9 ASI OUT2 ASI output interface

B10 ASI IN ASI input interface

B11 RS-232 Data interface, it is used to upgrade software

B12 LOOP THRU Satellite signal input interface

B13 TUNER IN Satellite signal output interface, it provides satellite signal for next IRD

B14 AC90~260V 50Hz/60Hz AC power socket

B15 FUSE Fuse, it is installed in power socket

I NS TA L L AT I O N

IDLV-3000Pisinstalledonthe19”rack,pleaserefertotheuser’smanualwhenyouinstallIDLV-3000P.

The following are typical applications using IDLV-3000P (For example: IDLV-3000P-30 series):

IDLV-3000P-30S

There are four options:

The IDLV-3000P-30S receives the QPSK signal, demodulates it to output ASI baseband transport stream •

toaDVBMPEG-2multiplexer.ThemultiplexerltersorrefreshesthePIDsoftheselectedprograms,

and rebuild the EPG, SI and other necessary tables.

The IDLV-3000P-30S receives the QPSK satellite signal, demodulates it and outputs ASI baseband •

transport stream to QAM modulator. The QAM modulator will transmit the QAM signal to CATV network.

The IDLV-3000P-30S receives the QPSK satellite signal, demodulates it and outputs ASI baseband •

transport stream to a DVB-IP gateway to serve as a signal source of a media player or an encoder.

The IDLV-3000P-30S provides baseband transport stream from satellite needed for monitoring and •

analyzing.

En

7

Connecting to a Multiplexer

M

U

L

T

I

P

L

E

X

E

R

1.1.1.4

1.1.1.3

CATV

Network

IDLV-3000P-30S

Professional IRD

IDLV-3000P-30S

Professional IRD

ASI TS

IDLV-3000P-30S

Professional IRD

IDLV-3000P-30S

Professional IRD

ASI TS

1.1.1.1

ASI TS

Input

QAM

Modulator

1.1.1.2

Connecting to a QAM Modulator

IDLV-3000P-30S

Professional IRD

IDLV-3000P-30S

Professional IRD

IDLV-3000P-30S

Professional IRD

IDLV-3000P-30S

Professional IRD

1.1.1.1

CATV

Network

ASI TS

IDLV-3000TM

QAM Modulator

IDLV-3000TM

QAM Modulator

IDLV-3000TM

QAM Modulator

IDLV-3000TM

QAM Modulator

Connecting to a TS Generator

DVB MPEG2

TS ANAL AYZER

IDLV-3000P-30S

Professional Decoder

8

IDLV-3000P-30C

IDLV-3000P-30Cisinstalledonthe19”rack.Pleaserefertotheuser’smanualwhenyouinstallit.

The IDLV-3000P-30C receives the signal from QAM modulator, demodulates it and outputs ASI baseband

transportstreamtoaDVBMPEG-2multiplexer.ThemultiplexerltersorrefreshesthePIDsoftheselected

programs, and rebuild the EPG, SI and other necessary tables and outputs ASI TS as well as decoded video and

audio through the audio/video of a TV.

Connecting to a QAM Modulator

RF

ASI TS

IDLV -3000P-30C

QAM Demodulator

IDLV -3000P-30C

QAM Demodulator

ASI TS

IDLV -3000P-30C

QAM Demodulator

IDLV -3000TM

QAM Modulator

IDLV -3000TM

QAM Modulator

IDLV -3000TM

QAM Modulator

Multiplexer

RF

ASI TS

IDLV -3000P-30C

QAM Demodulator

IDLV -3000TM

QAM Modulator

IDLV-3000P-30T

IDLV-3000P-30Tisinstalledonthe19”rack.Pleaserefertotheuser’smanualwhenyouinstallit.

The following describe typical applications of IDLV-3000P-30T:

The IDLV-3000P-30T receives the antenna signal, demodulates it to output ASI baseband transport stream •

toaDVBMPEG-2multiplexer.ThemultiplexerltersorrefreshesthePIDsoftheselectedprograms,and

rebuild the EPG, SI and other necessary tables.

The IDLV-3000P-30T receives the antenna signal and demodulates the signal. It will output ASI baseband •

transport stream to QAM modulator, the QAM modulator will transmit the QAM signal to CATV network.

The IDLV-3000P-30T receives the antenna signal and demodulates the signal. It will output ASI baseband •

transport stream to serve as a signal source of a media player or an encoder.

The IDLV-3000P-30T can provide baseband transport stream required for monitoring and analyzing.•

En

9

Connecting to a Multiplexer

1.1.1.2

MULTIPL

EXER

1.1.1.3

1.1.1.1

CATV

Net-work

IDLV-3000P-30T

Professional IRD

IDLV-3000P-30T

Professional IRD

ASI TS

IDLV-3000P-30T

Professional IRD

IDLV-3000P-30T

Professional IRD

ASI TS

Input

QAM

Modulator

Connecting to a QAM Modulator

IDLV-3000P-30T

Professional IRD

IDLV-3000P-30T

Professional IRD

IDLV-3000P-30T

Professional IRD

IDLV-3000P-30T

Professional IRD

1.1.1.1

CATV

Net-work

ASI TS

IDLV-3000TM

QAM Modulator

IDLV-3000TM

QAM Modulator

IDLV-3000TM

QAM Modulator

IDLV-3000TM

QAM Modulator

10

Basic Functions

The following describes the basic functions of your IDLV-3000P while watching satellite TV programs or listening

to broadcasts.

Select Channel

Toselectchannels,usethe▲▼keysofthefrontpanel.

Alternatively, while watching, press the OK key. A channel list will be displayed on the right side of the screen.

Press▲▼keystomovethroughthelistfromuptodown.TheOKkeywillconrmyourselection.Ifyoupress

ESC key, the list will disappear.

Channel Information

Every time you change channels, you will receive short-form program information for approximately 6 seconds.

Ifyouwanttocheckdetailedchannelinformation,youcouldpress◄keywhilewatchingorwhileShiftindicator

(Yellow) is on. If you press ESC key, the information will disappear.

En

11

Volume Control

WhileSHIFTindicatorisoffandwatching,youcouldpress◄►keysofthefrontpaneltocontrolvolume.

Notify: The IRD has 18 volume grades, while tuning volume, the LED of the front panel will display a respective

value from 0 to 17.

Audio Control

WhileSHIFTindicatorisoffandwatching,press▲keytoswitchaudiolanguage,press▼keytoswitchaudio

channel, you will receive short-form audio information for approximately 6 seconds.

TV/Radio switching

WhileSHIFTindicatorisonandwatching,press►keytoswitchTVmodeandBroadcastingmode.

Note:Pressing►keyfor2seconds,theSHIFTindicatorwillbe“ON”or“OFF”.

12

Menu operations

ConnecttheIDLV-3000Ptothepowersourceafterinstallationandcableconnection.Inarsttimeoperation

of the unit, the main menu will automatically be displayed. Subsequent to the initial operation, when the unit is

powered up, the last channel information will be displayed. The main menu can then be accessed by pressing

the MENU key of the front panel.

This Main Page menu consists of 4 primary sub menu items:

Channel Manager: Edit or delete programs.•

Installation:Setantennaparameters,searchingchannel,andrestorefactorydefaultconguration.•

Option Menu: Setting system parameters, antenna position and viewing IRD information. •

Common Interface: Checking status of common interface and setting descrambling mode. •

Notes:

The◄►keysletyoumovefromlefttorighttoanyitemwithinthemenu,the▲▼keysletyoumovefrom•

uptodowntoanyitemwithinthemenu,pressingOKkeytoconrmandpressingESCkeytoexit.

For the items with • ◄► mark,the◄►keysletyoumodifyparameters,orpressOKkeytodisplaythe

list, then select correct parameters in the list.

For the items with •

mark, use the ►keytodisplaythenumerickeypad,thenpressthe▲▼keysto

movetonumbers,usethe◄►keystoselectcorrectnumber,andpressOKtoconrmselection,use▲▼

keystoselect“OK”tomakenalconrmationofmodiedparameters,ortoselect“Cancel”tocancelthe

input data.

Channel Manager

The Channel Manager consists of two items:

TV Channel•

Radio Channel •

The functions related to the Radio Channel are the same as that for TV Channel, this manual will only detail the

TV Channel manager.

Select a TV Channel from the Main Page and press OK, the TV Channel Manager is displayed. On the left side

of the TV Channel menu you can see the channel list, on the right side, you can view the current channel in the

Picture in Graphic (PIG) mode (1/9 size of the normal screen size.) as well as channel information under the PIG

screen. When you move from one channel to another, the PIG will change accordingly.

In the TV Channel Manager, you can delete TV channels by using Delete Channel command.

To delete a channel, select the TV channel you want to delete using the ▲▼ keys and press OK.

An“X”marksthechannelthatwillbedeleted.RepeatthisprocedureforotherTVChannelsyoumaywantto

delete.(Tode-selectanymarkedTVchannelselectitandpressOK,the“X”willberemoved).

En

13

Ifyoudecidetodeletethemarkedchannels,pressESC.Amessage“Areyousuretodeletemarkedchannels”is

displayed.Select“OK”or“Cancel”inthemessageboxandthenpresstheOKkeytomakesureyouroperation.

PressESCtoexittheMainMenu,amessageisdisplayed“Savingdata…”.

After the data has been saved, you could view the channel list to check if the delete operation was successful.

Notes:

The deleted channel cannot be recovered unless you start a Channel Search again. •

Pleasedonotpoweroffwhenthemessage“Savingdata…”isdisplayed.•

14

INS TA L L AT I ON

IDLV-3000P-xxS

Antenna Setting

1. Antenna (LNB): Each antenna/LNB corresponds to a satellite.

2. Satellite: The name of the satellite which corresponds to the antenna/LNB.

3. LNB Type: Select your LNB type, there are three options.

Normal: Single Polarization LNBF •

Universal: Dual-pol. (Universal) LNB •

LNBF: Dual-pol. C-band LNB •

4. LNB Freq.: When LNB type changes, the frequency of LNB changes accordingly. You could input frequency

using numeric keys. IDLV-3000P supports two LNB local frequencies, if the channel couldn’t be searched with

En

15

rstlocalfrequency,itwillautomaticallysearchthechannelwithsecondlocalfrequency.

5. Switches(22KHz,DiSEqC):Youcouldselecttheswitcheswithwhichyouwanttoconguretheantenna

PressESCtonishantennasetting,themessage“AreyousuretochangethecongurationofAntennaset

up?” will be displayed. Select OK, press the OK key to conrm it and wait till the updated data has been

saved.

Channel Search

1. Antenna: Select the number of the antenna corresponding to the satellite you want to scan.

Note: On the right side of screen, you can see the corresponding parameters of the selected satellite, if it is not

correct, you can modify it under Antenna Setting.

16

2. Transponder:

Use◄►keystoselectthedesiredTP,ormovetothenewTPitem,youcouldedittheparametersofthisTP.

3. Frequency & Symbol Rate:

Edit the frequency and symbol rate. If the default values couldn’t meet your requirement, you can set the

satellite parameters manually.

4. Polarization: Select H or V.

5. ChannelSearch:Aftersettingthesatelliteparameters,youcouldpress◄►keystoselectsearchoptions:

SearchSAT:Searchallpre-denedchannelsfortheselectedsatellite.•

Search TP: Search all channels for one TP, which has been selected from the TP list. •

Search Network: Search channels on the network related to the selected TP. •

You could use it to search new satellite channel.

How to search:

After setting the parameters, move the cursor to the search column, choose your desired search option, then

press OK to start searching.

During the scanning procedure you can see a list of the previously searched channels in the Searched List Box

onthescreen.Oncompletionofsearchingchannels,youcouldmovecursortoselect“VIEW”or“EXIT”.

Page is loading ...

Inverto IDLV-3000P User manual

Inverto IDLV-3000P User manual

Related papers

Other documents