2. Anviz
  3. BL100

Anviz BL100 Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Anviz BL100 Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
B.ListofLockAccessories
1
Keyhole
Cover
6 Screw(4PCS)
2
Frontpanel
Assembly
7
4PCSAA
Batteries
3
Silicagel
backingplate
8
Rearpanel
assembly
4 Lockbody 9 Screw(2PCS)
5
BackLining
Plate
10 Key (2PCS)
.Ⅲ Confirmthedoorinf ormationbeforeinstallation
1.InstallationRequirements
This fingerprint lock is not configured with a handle, and the user can install it on the door as desired. The
fingerprintlockisapplicabletodoorsof3550mminthickness.
2. Makesureofthedooropeningdirectionsandlockbodydirections
(1).Make sureofthedooropeningdirections.Thelockbody'soutsideandinsidecan'tbesetcontrary.Assume
you are standing outside and facing a door and then thereare four door opening directions: Left inward, left
outward, right inward and right outward. Left inward/outward means the door swings inward/outward with
hinges on the left; right inward/outward means the door swings inward/outward with hinges on the right, as
showninthefollowing Figure1:
(2).Makesureofthelockbody directions. According tothedooropeningdirectionsto makesureof the lock
bodydirections,shownasthefollowing Figure2:
.Ⅰ ReferenceToolsforInstallingtheDoorLock
1Hammer 2Screwdriver 3Chiselforwoodworking 4Anglesquare 5Percussiondrill
6Holesaw 7Polisher 8Rivetgun 9Carpenter'spencil 10Pliers
.QuickReferenceⅡ
A.QuickreferenceforInstallationGuide
Ø Confirm the door information beforeinstallation, pleasesee Ⅲ. Confirm the door information before
installation;
Ø InstallLockBody,pleasesee Ⅳ.InstallLockBody;
Ø ConfirmthelengthofLockingBar,pleasesee Ⅴ.ConfirmthelengthofLockingBar;
Ø InstalltheFrontpanelAssembly,pleasesee Ⅵ.InstalltheFrontpanelAssembly;
Ø InstallBatteries,pleasesee Ⅶ.InstalltheBatteries;
Ø InstalltheRearpanelAssembly,pleasesee Ⅷ.InstalltheRearpanelAssembly;
Ø UseInstruction,pleasesee Ⅸ.UseInstructions;
Ø TheBasicOperation,pleaseseeⅩ.TheBasicOperation;
Ø RoutineMaintenance,pleasesee Ⅺ.RoutineMaintenance.
BL100InstallationGuide
Version: V1.0
Date: 2012.3.16
1
2
Ⅳ.InstallLockBody
1. Determine the installation height and installation location; stick the holedrilling template to an appropriate
locationaccordingtothedooropeningmode,asshownin Figure 41.
2. Insertthe Lock Body into thematching Hole Slot. asshownin Figure5:
?Note:There hasa"•UP"flagontheLockBody.BeforeinstallingtheLockBody,confirmhowtoinstallit
basedonthetipflag.
SetthelengthoftheLockBodybasedonthedistancefromtheDoorEdgetothecenterofthecircle(thatis,the
openingholedistanceisabout60mmor70mm,asshownin Figure41).
Theopeningdistancematching thedefaultlength ofthelockbodyis60mm.Ifthedistanceof70mmisrequired,
resetthelengthofthelockbodyinthe followingsteps:
(1). Holdthepart ①ofthe Lock Body,rotatethepart ② by 45°,andpullbackpart ②. Asshownin Figure42.
(2).Rotatepart②by45°inthe otherdirectiontomakethecardpillaroftheLockBodytobeembeddedintothe
matchingcardholeof70mm.Thatis,setthelengthoftheLock Body to70mm.
JNote: WhenyoushortenthelengthoftheLock Body,performthefollowingsteps:
(1). Hold the part ①, rotate the part② by45°, and push part ② ahead. (2). Rotate part ② by45° inthe other
directiontomakethecardpillarofthe LockBody tobeembeddedintothematchingcardholeof60mm.
(3). Tosetthelockas"LeftOpen" or "RightOpen" ontheRear panel Assembly,shownas Figure3:
Asshownin Figure3,therehasa "Leftopen/RightOpen" setSwitchontheRearpanelAssemblyofthefingerprint
lock.Theusercanturntheswitchtotheleftside(L),namely setthedoor'sopeningdirectionsas"LeftOpen";if
turntheswitchtotherightside(R),thensetthedoor'sopeningdirectionsas"RightOpen".
Note:① Before installthefingerprintlock,youmustmakesureofthe door'sopeningdirectionasLeftOpenor
RightOpenatfirst;②Accordingtothedoor'sopeningdirection,switchthe"Left/RightOpen"setswitchtothe
corresponding position (Left Open, then switch to the left side; Right Open, then switch to the right side); ③
Accordingtothedoor'sopeningdirectionto drillaholeandtroughinthedoor,andtheninstalltheLockBody.
3
4
Figure1 Figure2
Figure3
Figure41
Figure5Figure42
Ⅵ.InstalltheFrontpanelAssembly
1. Install aSilicagel backing plateonthe fFront panel Assembly(moistureproof/ waterproof). As shownin
Figure12.
2.Stretchthe Spring BoltbacktotheLock Body andpullthe Connecting Wireoutoftheholeatthebottomofthe
Lock Body.
3.InstalltheFrontpanelAssemblyintothematchingHole Sloton thedoor.(Therearethreeholes ontheLock
Body, as shown inthe preceding figure.Thecylinderonthe foreplate composition mustbe pulledoutfromthe
crossshapedholeoftheLock Body andtheLocking Bar mustbeverticaltotheground.),asshownin Figure13.
4.Installthe BackLining Plate tothemapping HoleSlot.PulltheConnectingWireoutoftheOvalshaped Hole
ofthe Back Lining Plate (Asshownin Figure14) andfixthe Back Li ning Plate and FrontpanelAssembl y using
ascrewdriver,asshownin Figure15.
3. After the procedure is completed, fix the Lock Body using a screwdriver, as shown in Figure 6. Insert the
screwdriver intothecrossshapedhole of theLockBody. Whenyourotate thecylinderclockwise,itsprings out
automatically,asshowninFigure7.Whenyourotatethecylindercounterclockwise,itspringsbackautomatically,
asshownin Figure8.
Ⅴ. ConfirmthelengthofLockingBar
1.Installthe Frontpanel Assemblyofthelockontothedoor(Pleasesee .InstalltheFrontpanelAssemblyⅥ ).As
shownin Figure9:
2.CheckwhethertheLockingBaristoolong.Ifyes,taketheF rontpanelAssemblyoffandcutawaytheexcess
partofthe Locking Bar (see MethodforCuttingLockingBar). Asshown in Figure10.
MethodforcuttingLockingBar :SupposethatthepartoftheLockingBarthatstretchesoutoftheHoleSloton
thedoorisCD,asshowninFigure11.CutawaytheLocking BarfromAtoensurethattheLockingBardoesnot
stretchoutofthe HoleSlot .
5
6
Figure6 Figure7 Figure8
Figure9 Figure10 Figure11
Figure12 Figure13
Figure14 Figure15
FrontpanelAssembly
Silicagelbackingplate
3.CovertheSilicagel Backing PlateontotheRearpanelAssembly,turntheLockButtontomaketheHoleSlot
verticaltotheground,andinsertLockingBarintotheHoleSlot,asshowninFigure 19.Inthiscase,whenyou
turnthe Lock Button,theboltcansprungoutorbackautomatically.
4.PushtheRearpanel Assembly aheadtoensurethatitcancoverthewhole Back Lining Plate.Installscrewsand
fixthemusingascrewdriver. As shownin Figure 20.
.Ⅸ UseInstructions
1.PanelDescription
Ⅶ.InstalltheBatteries
1. PreparefourAAbatteries.Youareadvisedtousenewbatterieswiththesamebrand.
2. Putbatteriesintothe RearpanelAssembly properly. As shownin Figure161 and 162:
Ⅷ.Installthe Rearpa nelAssembly
1. Pullthe Connecting Wire intothe Wire Hole ofthe RearpanelAssembl y. Asshownin Figure17:
2. Tuckupthe Connecting Wire forfurtherRearpanelAssembly installation. Asshownin Figure18.
7
8
①FingerprintCollector
②Start key/LEDStatus indicator
③Numberkeys
⑤Emergency Power Interface
④KeyHole
⑥
ScrewHole
⑦LockButton
Figure161
Figure162
Figure17
Figure18
Figure19
Figure20
WireHole
RearpanelAssembly
AAbatteries
① ②
5.BatteryLowVoltageProtection
Whenthebatteryislow,therearealarmsignalstowarnuserstochangethebatteryasfollows:
(1). When the battery voltage is lower than 4.8V, the buzzer will make short sharp sounds for five times when
startingthemachine.Userscanunlockitnormallybutfailtoentertheadministrativemode.
(2).Whenthebatteryvoltageislowerthan4.5V,thebuzzerwillmakeshortsharpsounds forfivetimes,andthen
themachinewillbeswitchedoffautomatically.
JNote:Whenthelowvoltagealarmoccurs,pleasechangethebatteryintimetoavoidtheimpactontheworkof
the fingerprint lock. Avoid losing data caused by instable power supply (It is suggested to change the battery
immediately whenthebatteryvoltageislowerthan4.8V).
Ⅹ. TheBasicOperation
Ⅰ. ChangeMasterPassCode(MPC)
1. Press keytostartlock,andthenentertheVerifyState.TheLEDflashesgreenlight,andtheNumpadarea's
bluelightwillbeon.
2.Pressandholdthe keyuntilyouhear1longbeepandtheGreenLEDputout,andthentheKeypadarea
FlashesBluelight.Pressnumberkey of thelocktoinputthedefaultMPC"98989",andthenpress key to
entertheManagementMode. ThegreenLEDputoutandtheKeypadareacontinueflashbluelight.
2.Precautions
(1).Afterthefingerprintlockisinstalled,thelockisintheteststate,andthereforeanyfingerprintsandpasswords
canopen the lock.You must modify theMaster Pass Code(MPC).Thelockcan be used normally only afterthe
UserIDofanadministratorisentered.IftheMPCisnotmodified,theotherfunctionsofthesystemexceptforthe
initialization system are not available in the management mode. If no administrator is registered, ordinaryusers
cannotalsoberegistered.
JNote: Themethodandstepof changeMasterPassCode,Enroll AdministratorandEnrollOrdinaryuser,please
see BL100 Fingerpri ntLock UserManual.
(2).Donotremovebatterieswhenmatching,enrollingordeletingfingerprintsbecausethesuddenpowerdownmay
resultindatalossoffingerprintlocks.Priortoremovingbatteries,makesurethefingerprintlockisnotinworking
state.
(3).Itisrecommendedtoreplacethefingerprintlockbatteriesatleastonceeverysixmonthstoavoiddamagingthe
circuitduetothebatteryleakage.Donotusebatterieswithpoorquality.
3. LEDBacklightIndicators
TheLEDBacklightIndicatorscontentthreecolors:Red,GreenandBlue.
Ø Thegeneralrule:
Successful =1LongBeep/LEDFlashesGreen.
Failed =2ShortBeeps/LEDFlashesRed.
Ø VerifyState:GreenLEDflashbysecond.
Ø ManagementMode:BlueLEDflashbysecond
4.UnlockwithanEmergencyMechanicalKey
Youcanopenthedoorusinganemergencymechanicalkeyincasetheelectroniccomponentdoesnotoperate.
①Useyourfingernailsorahardchiptotakedownthelockcover.
②Inserttheemergencykeyintothekeyholeandrotate90ºtounlock.
9 10
Ⅲ.EnrollanOrdinaryUser
Ø EnrollaFingerprintOrdinaryUser
1. Press keytostartthelockandentertheVerifyState.
2.TherehavetwomethodstoentertheManagementMode: ①Pressandholdthe keyuntilyouhear1long
beep, enterthe5 digitsMPC, andthenpress key to entertheManagementMode.② Verify the registered
administrator'spasswordandfingerprinttoentertheManagementMode.
3. Press"1"toentertheEnrollOrdinaryUser'sFingerprintMode.
4. Input3digitsUserID,thenpress keytoconfirm.
JNote:Theordinaryusers'IDmustbetween"001"and"994".
5. Press fingerinthe scanner areaproperly, and repeatit for threetimes,untilyouhear one longbeepand LED
flashesGreen,namelyenrollmentsuccessful.
Ø EnrollaPasswordOrdinaryUser
1.Press keyto startthelock andentertheVerify State.EntertheManagementMode;seethe methodson
howtoenterthemanagementmodeinthe EnrollaFingerprint OrdinaryUsers.
2. Press"2"onthelocktoentertheEnrollOrdinaryUser'sPasswordMode.
3. Input3digitsUserID,andpress keytoconfirm.
JNote:Theordinaryusers'IDmustbetween"001"and"994".
4.Input 4 digitsuserpassword,press keytoconfirm.Enterthe4digituserpasswordonce againandpress
keytoconfirmuntilyouhearonelongbeepand LEDflashesGreen.TheKeypadarealightsblueLEDand
the keylightsgreenLED,namely register successful.
Ⅳ. UserVerification
Ø TheFingerprintVerification
1. Press keytostartthelockandentertheVerifyState.The FingerprintCollector isinactivestate.
2. Pressfingerinthefingerprintscannerareaproperly,untilyouhearonelongbeep,namelycollectsuccessful.
(1)Ifverifysuccessful,thebuzzerwillgivealongbeepandunlockautomatic,thegreenLEDandtheFingerprint
Collectorwillputout,theGreenLEDat keywilllightfor3seconds,atthismomentyourcanpress
keytolock.
3.Press"5"keyonthelockandenterthenew5digitsMPC,thenpressthe keytoconfirm.Enterthenew
MPConceagainthenpressthe keytoconfirm.Onceyouhear1longbeepandthe keyflashesgreen,
namelyyouhavesuccessfullychangedthe MPC code.
.Ⅱ EnrollanAdministrator
1. Press keytostartlock,and thenentertheVerifyState.
2.Pressandholdthe keyuntilyouhear1longbeep,enterthe5digitsMPC,andthenpress keyto
entertheManagementMode.
3. Press"9"onthelocktoentertheEnrollAdministratorMode.
Ø EnrollaFingerprintAdministratorUser
JNote: 13stepsaresameasabove.Hereisnolongertorestatement.
4.AfterentertheEnrollAdministratorMode,pressnumberkeysofthelocktoenter3digitsuserID,andthenpress
keytoconfirm.
JNote:TheadministratorUser'sIDmustbetween"995"and"999".
5. Press fingerinthe scanner areaproperly, and repeatit for threetimes,untilyouhear one longbeepand LED
flashesGreen.
Ø EnrollaPasswordAdministratorUser
JNote:13stepsaresameasabove.Hereisnolongertorestatement.
4. AfterentertheEnrollAdministratorMode,enter3digitsuserID,press keytoconfirm.
5.Press4digitsuserpasswordandpress key toconfirm,andthen enterthe4digitsuserpasswordonceagain
andpress keytoconfirm,untilyouhearonelongbeepandLEDFlashesGreen(Ifitfailstoregisteritwill
give2shortbeepsandLEDwillflashred).
JNote: ①IfPasscodedoesnotmatchorinputthewrongdigitpassword,thenyouhavetwotimestotryagain.
Ifyourinputthewrongatthethirdtime,thenitwill prompt failregistration.Inthiscaseyouwillneedtofollowstep
1tooperateagain.②Ifsuccessful,itwillautomaticallyexittheEnrollAdministratorMode.③Pressandhold"0"
key,canexitanytime. ④Ifyouwanttoenrollmoreadministratoruser,andthenrepeatthestep15.
11
12
3.Input"000"andpress keytoconfirm,theninput"000"againandpress keytoconfirm.Thebuzzer
willgivealongbeep,the keyflashgreenlight,namelysuccessfuldeleteallusers.
?Notice:Theoperationcanonlydeleteordinaryusers.Ifyouwanttodeleteadministrator,youshoulddoreset
operation.
Ⅺ.RoutineMaintenance
1.Thelocksurfaceisforbiddentocontactcorrosivesubstances.Otherwise,theprotectivelayerofthelocksurface
maybedamaged,andtherefore the glossinessofthelocksurfacemaybedecreased.Tokeepthelocksurfaceglossy,
usethefurniturepolishwaxtopolishthelocksurfaceregularly.
2. Usetheclothtocleandirtafterthefingerprintcollectorisusedforlongtime.
3.Changebatteriesintimewhenthealarmonthelowpowerrings.Youmustreplacethefouroldbatterieswithfour
newbatteriesofthesamebrand(the alkalinebatteryof1.5V)once.
4. Regularlycheckwhetherscrewsareloose.
(2)Ifverificationfailed.Thebuzzerwillgivetwoshortbeeps,theredLEDat keywilllightfor3s,thenthe
greenLEDwillflash,theusercanusefingerprinttoverifyagainuntilverifysuccessful.
Ø ThePasswordVerification
1. Press keytostartthelockandentertheVerifyState.
2. Pressnumberkeyoflocktoinputthecorrect4digitspassword,andpress keytoconfirm.
(1)Ifthe password iscorrect,thenverify successful,the buzzerwill give along beepandunlock automatic,the
greenLEDatFingerprintCollectorwillputout,theGreenLEDat keywilllightfor3s,atthismomentyou
canpressthe keytolock.
(2)Ifthe passwordiswrong, thentheverification failed.The buzzerwillgivetwo shortbeeps,the RED LEDat
keywilllightfor3s,thenthegreenLEDwill flash,the usercaninputpasswordtoverifyagainuntilverify
successful.
JNote:Aftersuccessfulverification,thelockisinunlockingstate.Ifyouwanttolock,press keytostart
thelock,andthenpressthiskeyagaintolockandpoweroff.
Ⅴ.DeleteUser
Ø Deleteauser
1.Press keyto startthe lockandentertheVerify State.Seethe methods on howtoenter the management
modeinthe EnrollaFingerprint O rdinaryUsers.
2. Press"3"onthelocktoentertheDeleteUserMode.
3.Pressnumberkeyofthelocktoinputthe User'sIDwhichoneyouwanttodelete,andthenpress keyto
confirm.InputtheuserIDagain,andpress keytoconfirm,thebuzzerwillgivealongbeep,the key
lightsgreenlight,namelysuccessfuldeletetheuser.
4.Afterdeletingtheuser,youcanrestartthefingerprintlockandverifythedeleteduser'sfingerprintsorpassword
againtocheckwhethertheuserisdeletedforsure.
?Notice: Theadministratorcan'tdeleteitselfand thelastadministrator.
Ø Delete AllOrdinaryUsers
1.Press keytostartthelockandentertheVerify State. Seethemethodsonhowtoenterthemanagement
modeinthe EnrollaFingerprint O rdinaryUsers.
2. Press"6"onthelocktoentertheDeleteAllOrdinaryUserMode.
13
14
/