Mainstays MS17-D1-1011-01 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.

PLEASE READ AND KEEP FOR FUTURE REFERENCE.

Date 2018-02-28 Rev. 0001-A Factory: KONRIC

Entertainment Center

Stock # MS17-D1-1011-01 Black Oak Finish

# MS18-D2-1011-12 Canyon Walnut Finish

# MS18-D2-1011-10 White Finish

ADULT ASSEMBLY REQUIRED

If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the

store where it was purchased. Please call our customer service number and have your instructions

and parts list ready to provide the model name, part name or factory number:

866-942-5362

Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday

Or visit our web site 24 hours a day, 7 days a week for product assistance at

www.whalenstyle.com

Or e-mail your request to parts@whalenfurniture.com

LOT NUMBER:

DATE PURCHASED: / /

OR

2

MANUFACTURER: Whalen Furniture Manufacturing

CATALOG: Entertainment Center

MADE IN CHINA

SPECIAL NOTE

Please read the instruction sheets completely before assembly. Examine all packaging

material before discarding carton. Remove any remaining staples from the carton before

discarding. Remove all parts from carton and separate into groups as indicated on part

list. Please ensure all parts are included prior to assembly. Use of power tools to

complete assembly is not recommended.

M A X I M U M R E C O M M E N D E D W E I G H T L O A D S

MAXIMUM LOAD 50 lb. (22.7 kg)

FITS UP TO MOST 55” FLAT PANEL TVs

MAXIMUM LOAD 135 lb. (61.3 kg)

THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT

PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.

NEVER USE WITH LARGER/HEAVIER THAN RECOMMENDED FLAT PANEL TVS OR EQUIPMENT. TO

AVOID INSTABILITY, PLACE FLAT PANEL TV IN THE CENTER OF THE UNIT; THE BASE OF THE

TELEVISION MUST BE ABLE TO REST ON THE SUPPORTING SURFACE OF THE UNIT WITHOUT

OVER-HANGING THE EDGES. IMPROPERLY POSITIONED FLAT PANEL TVS, OR FLAT PANEL TVS

INCLUDING OTHER EQUIPMENT THAT EXCEED RECOMMENDED SIZE AND WEIGHT LIMITS

COULD FALL OFF OR BREAK THE UNIT, CAUSING POSSIBLE SERIOUS INJURY.

PLACE TV BEHIND THE STOPPER

3

IMPORTANT

Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-

abrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual.

NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED

OFF WITH DAMP CLOTH.

Insert the Dowel at least half way by tapping lightly with a rubber mallet, IF NECESSARY.

CAM LOCK SYSTEM OPERATION

HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS

1. Screw the Cam Bolt into the threaded inserts on the panel. Connect both panels together; making sure Cam

Bolt goes into the pre-drilled hole on the end of panel for Cam Lock.

2. Insert the Cam Lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of Cam

Lock faces out and points towards Cam Bolt.

3. Take a Phillips screwdriver and rotate the Cam Lock clockwise to lock the Cam Bolt in place.

4. Plug the Cam Lock Cover into the cross slot of the Cam Lock to conceal the Cam.

You are now ready to assemble the fireplace.

X

FINAL

1 2 43

4

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts and hardware are present

before beginning assembly.

A- Top Panel (Qty. 1) B- Bottom Panel (Qty. 1)

C- Left Side Panel (Qty. 1) D- Right Side Panel (Qty. 1)

E- Large Divider Panel (Qty. 1) F- Small Divider Panel (Qty. 1)

G- Large Fixed Shelf (Qty. 1) H- Back Panel (Qty. 1)

I- Middle Small Fixed Shelf (Qty. 2) J- Top/Bottom Small Fixed Shelf (Qty. 2)

K- Middle Adjustable Shelf (Qty. 2) L- Side Adjustable Shelf (Qty. 2) M- Stop Rail (Qty. 1)

5

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts and hardware are present

before beginning assembly.

(1) Cam Lock (Qty. 24+1 extra) (2) Cam Bolt (Qty. 24+1 extra)

(3) M15 x 40 mm Wood Dowel (4) M6 x 30 mm Wood Dowel

(Qty. 8+1 extra) (Qty. 40+2 extra)

(5) 5/16" x 40 mm Bolt (6) Lock Washer (7) Flat Washer

(Qty. 8+1 extra) (Qty. 8+1 extra) (Qty. 8+1 extra)

(8) Plastic Cap (Qty. 4+1 extra) (9) Shelf Pin (Qty. 16+1 extra) Hex Wrench (Qty. 1)

Glue Touch-up Pen (Qty. 1) Tipping Restraint Hardware Kit (Qty. 2)

(Qty. 1) (Not included for White Finish) (Included in plastic bag)

Tools required: Hex wrench (provided), Phillips screwdriver and hammer (not provided).

6

Assembly Instructions

1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a

carpeted floor or the empty carton to avoid any scratch.

2. Securely screw the Cam Bolts (2) into the designated small holes on the Bottom Panel (B) and the Side

Panels (C and D) using a Phillips screwdriver.

Cam Bolt

(10 used in this step)

②

D

C

B

2

7

Assembly Instructions

3. Securely screw six Cam Bolts (2) into the designated small holes on the Large Divider Panel (E) on

both sides.

Cam Bolt

(6 used in this step)

②

2

E

8

Assembly Instructions

4. Securely screw four Cam Bolts (2) into the designated small holes on the Large Fixed Shelf (G) on both

sides.

Cam Bolt

(4 used in this step)

②

2

G

9

Assembly Instructions

NOTE: According to your wall structure, you can build the tower at left or right side.

5. Depend on the tower configuration you preferred, securely screw four Cam Bolts (2) into the designated

small holes on the Top Panel (A) as shown.

A

2

Cam Bolt

(4 used in this step)

②

OR

10

Assembly Instructions

6. Attach two Middle Small Fixed Shelves (I) to the Large Divider Panel (E) with two 30 mm Wood

Dowels (4) and two Cam Locks (1) in each (Refer to page 3 on Cam Lock system operation

supplement).

7. Attach two Top/Bottom Small Fixed Shelves (J) to the Large Divider Panel (E) with four 30 mm Wood

Dowels (4).

8. Repeat the same procedure to attach the Left Side Panel (C) at the opposite end.

J

C

E

I

4

1

4

UP

Cam Lock

(8 used in this step)

①

M6 x 30 mm Wood Dowel

(24 used in this step)

④

11

Assembly Instructions

9. Attach the Large Fixed Shelf (G) to the Large Divider Panel (E) and Right Side Panel (D) with four 30

mm Wood Dowels (4) and four Cam Locks (1).

G

1

4

C

E

D

UP

1

4

D

C

E

G

4

1

Cam Lock

(4 used in this step)

①

OR

M6 x 30 mm Wood Dowel

(4 used in this step)

④

12

Assembly Instructions

10. Attach the Small Divider Panel (F) to the Large Fixed Shelf (G) with two 30 mm Wood Dowels (4) and

two Cam Locks (1).

UP

C

D

G

F

E

1

4

Cam Lock

(2 used in this step)

①

M6 x 30 mm Wood Dowel

(2 used in this step)

④

13

Assembly Instructions

11. Attach the Back Panel (H) to the Large Fixed Shelf (G) with two 30 mm Wood Dowels (4) as shown.

UP

4

G

F

D

C

E

H

M6 x 30 mm Wood Dowel

(2 used in this step)

④

14

Assembly Instructions

12. Insert four 40 mm Wood Dowels (3) into the bottom holes on the Side Panels (C and D) and insert four

30 mm Wood Dowels (4) into the bottom holes on the Divider Panels (E and F). Position the Bottom

Panel (B) onto the inserted wood dowels and attach to the Divider Panels (E and F) with four Cam

Locks (1).

Cam Lock

(4 used in this step)

①

M6 x 30 mm Wood Dowel

(4 used in this step)

④

M15x 40 mm Wood Dowel

(4 used in this step)

③

3

D

H

1

UP

C

E

G

F

B

4

15

Assembly Instructions

13. Fasten the Bottom Panel (B) to the Side Panels (C and D) with four Bolts (5) and four Washers (6 and 7).

Lock Washer

(4 used in this step)

⑥

Flat Washer

(4 used in this step)

⑦

B

UP

C

E

G

F

D

H

5

6

7

6

7

5

5/16" x 40 mm Bolt

(4 used in this step)

⑤

16

Assembly Instructions

14. Insert four 40 mm Wood Dowels (3) into the top holes on the Side Panels (C and D) and insert four 30 mm

Wood Dowels (4) into the top holes on the Large Divider Panel (E) and the Back Panel (H). Position the

Top Panel (A) onto the inserted wood dowels and attach to the Large Divider Panel (E) with two Cam

Locks (1).

Cam Lock

(2 used in this step)

①

M6 x 30 mm Wood Dowel

(4 used in this step)

④

M15x 40 mm Wood Dowel

(4 used in this step)

③

B

UP

C

E

G

F

D

H

A

3

4

1

17

Assembly Instructions

15. Fasten the Top Panel (A) to the Side Panels (C and D) with four Bolts (5) and four Washers (6 and 7).

16. Cover the countersunk holes on Top Panel (A) by inserting four Plastic Caps (8). Gently tap the Plastic Cap

with a rubber mallet to ensure they are fully seated.

B

UP

E

G

F

D

H

C

A

5

6

7

8

Plastic Cap

(4 used in this step)

⑧

Flat Washer

(4 used in this step)

⑦

5/16" x 40 mm Bolt

(4 used in this step)

⑤

Lock Washer

(4 used in this step)

⑥

18

Assembly Instructions

17. Ask for assistance to stand the unit upright.

18. Fasten the Back Panel (H) to the Top Panel (A) and the Large Fixed Shelf (G) with four Cam Locks (1).

Cam Lock

(4 used in this step)

①

A

H

G

1

19

Assembly Instructions

19. Insert the Shelf Pins (9) into the desired holes in the sides of the compartments. Make sure you place the

four Shelf Pins in the same level so the shelf is not tilted. Tilt and rest the Adjustable Shelves (K and L)

onto the Shelf Pins (9) with the end notches of the Shelf fit onto the Shelf Pins properly.

Shelf Pin

(16 used in this step)

⑨

D

E

F

K

L

10

9

K/L

20

Assembly Instructions

NOTE: You must install the strip stopper to prevent the TV from tipping when placing your flat panel

television directly on the console.

20. Remove the paper backing from the Stop Rail (M), then properly align the Stop Rail with the top edge

of the stopper template on the Large Fixed Shelf (G). Press down on the Stop Rail to help adhesion.

21. Carefully remove the stopper template from the Large Fixed Shelf (G).

M

G

Page is loading ...

Mainstays MS17-D1-1011-01 User manual

This manual is also suitable for

Mainstays MS17-D1-1011-01 User manual

in other languages

Other documents