Noble House 305010 Operating instructions

Brand
Noble House
Model
305010
Type
Operating instructions

This manual is also suitable for

Label Picture Description QTY
A Backrest 1
B Left Armrest 1
C Right Armrest 1
D Seat Panel 1
Caution : You must read this before you proceed
Dining Chair
Label Picture Description QTY
E Allen Key 1
F Bolt (M6*35MM) 5
G Bolt (M6*20MM) 3
H Flat Washer 8
Before Beginning Assembly:
Step 1
This Dining Chair has multiple parts and may require up to 45 minutes to assemble.
To give you an overview of the Dining Chair parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions herebelow to familiarise yourself with the parts and steps before
assembly.
Open the carton and place all the parts onto a clean, non-marring surface, preferably a working top.
Place Left Armrest(B) on the ground, as shown in picture above.
Backrest(A)
Left Armrest(B)
Right Armrest(C)
Seat Panel(D)
FRONT FACING
Step 3
Step 2
Attach and secure Backrest(A) to Left Armrest(B) using Bolts(G) and Washers(H) with Allen Key(E)
Only Loosely Tighten Bolts.
Attach the Seat Panel(D) to the assembled Backrest(A) and Left Armrest(B) using Bolts(F) and Washers(H) with
Allen Key(E)
Only Loosely Tighten Bolts.
D
A
B
A
B
Step 4.1
Step 4.2
Place the Right Armrest(C) onto the mounting bolts, and secure with Bolts(G) and Washers(H) with Allen Key(E).
Only Loosely Tighten Bolts.
Turn the chair over, and assemble the Right Armrest(C) using Bolts(F) and Washers(H) with Allen Key(E)
Only Loosely Tighten Bolts.
c
C
Step 6
Step 5
Place the dining chair on a LEVEL SURFACE to check for wobbles.
If it wobbles lift the dining chair to some 20cm to 30cm height from the ground.
Keep your feet and toes well away from the drop zone.
Drop the dining chair freely and vertically with the four legs, hitting the ground, all at the same time.
This Drop Test will help to ensure that all the bolts and gaps to all reach full alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles found, slowly and steadily, turn the chair upside down.
Then, proceed to tighten all bolts in a sequential manner.
CAUTION : When tightening these bolts, tighten sequentially.
DO NOT tighten any screw fully and then towards the next one.
This would cause the frame to warp.
If there is still wobbles, loosen the bolts and execute this same drop tests.
WARNING!! IF DINING CHAIR IS NOT STABLE , IT COULD LEAD TO DAMAGING THE PRODUCT.
Your Dining Chair is ready for use.
Test again
If wobble
30CM~50CM
Page 1 of 6Page 1 of 6
Caution : You must read this before you proceed
TABLE
CAUTION: This Table is NOT a TOY.
Keep your child / children at bay during the assembly
process.
For moving the Table and to prevent damage to the Table,
For moving the Table and to prevent damage to the Table,
two adults are needed to execute this action.
Noble House Home Furnishings LLC
Page 2 of 6
Label Picture Description QTY
A Table Top 1
B Leg 4
C Leg Support 4
Label Picture Description QTY
Bolt (M6x50mm) 9
1
Bolt (M6x50mm) 9
3 Washer 9
4 Allen Key 1
Before Beginning Assembly:
1
2
3
4
Noble House Home Furnishings LLC
Screw (M6x35mm) 9
Page 3 of 6
OVERVIEW
FRONT FACING
Leg (B)
Table Top (A)
Leg Support (C)
Step 1
This Table has multiple parts and may require up to 30 minutes to assemble.
To give you an overview of the Table parts, the above picture is to help you
put the various parts into perspective. Please read through the instructions
below to familiarise yourself with the parts and steps before assembly.
Unpack and place all parts on a clean, non-marring surface.
Noble House Home Furnishings LLC
Page 4 of 6
Step 2
Attach Leg(B) to the Table Top(A) using Bolt(
①
) and Washer(
③
) with Allen
Key(
④
).
Do not fully tighten Bolts
A
B
1
4
3
Step 3
① ③
④
Do not fully tighten Bolts
Repeat the same process with the remaining three Legs(B)
Place Leg Support(C) between Table Top(A) and Leg(B), as shown above.
3.1) Secure Leg Support(C) to Table Top(A) using Screw(
②
) with Allen
Key(
④
)
3.2) Secure Leg Support(C) to Leg(B) using Screw(
②
) with Allen Key(
④
)
Do not fully tighten Screws
C
B
A
4
2
Step 3.1
Step 3.2
2
4
④
② ④
Do not fully tighten Screws
Repeat the same process with the remaining three Leg Supports(C).
Noble House Home Furnishings LLC
Page 5 of 6
Step 4
Turn the Table over, with assistance from your partner.
EXERT pressure, floorwards, onto the Table.
This pressure will help the Legs and Table Top reach alignment at all joints.
Check for wobbles.
In a sequential manner, gradually tighten all Bolts and Screws until evenly
secured.
Step 5
Inspect Table and make sure all parts are adequately connected.
secured.
When tightening the Bolts and Screws tighten sequentially.
Do not tighten any Bolt or Screw fully and then move towards the next one.
This could cause the frame to warp.
If there are still wobbles, loosen the Bolts and Screws and execute the
same above process.
If the Table is not Stable it could lead to damage to the product.
Inspect Table and make sure all parts are adequately connected.
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Noble House Home Furnishings LLC
Page 6 of 6
OUTDOOR
Noble House Home Furnishings LLC
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13

Noble House 305010 Operating instructions

Brand
Noble House
Model
305010
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents