Noble House 300395 Operating instructions

Label Picture Description QTY

A Armrest 2

B Backrest 1

C Seat 1

D Seat Cushion 1

Caution : You must read this before you proceed

DINING CHAIR

Page 1 OF 6

E Back Cushion 1

Label Picture Description QTY

① Bolt (M6*35MM) 11

② Washer 11

③ Allen Key 1

Before Beginning

Assembly:

Page 2 OF 6

Step 1

This Dining Chair has multiple parts and may require up to 30 minutes to assemble. To

give you an overview of the Dining Chair parts, the above picture is to help you put the

various parts into perspective. Please read through the instructions below to familiarise

yourself with the parts and steps before assembly.

Open the carton and place all the parts onto a clean, non-marring surface.

Place the Armrest(A) face up.

Attach Backrest(B) to Armrest(A) using Bolts(①) and Washers(②) with Allen Key(③).

Do not fully tighten the Bolts.

Page 3 OF 6

Step 2

Step 3

Place the Seat (C) between the Backrest(B) and Armrest(A).

Attach Seat(C) to Armrest(A) and Backrest(B) using Bolts(①) and Washers(②) with

Allen Key(③).

Do not fully tighten the Bolts.

Place the other Armrest(A) against Backrest(B) and Seat(C).

Attach Armrest(A) to Backrest(B) and Seat(C) using Bolts(①) and Washers(②) with

Allen Key(③).

Do not fully tighten the Bolts.

Page 4 OF 6

Step 4

Step 5

Your Dining Chair is ready for use.

This Dining Chair can only be used on the flat and level surface.

Place the Dining Chair on a LEVEL SURFACE to check for wobbles.

If it wobbles, lift the Dining Chairr some 20cm to 30cm high from the ground.

Keep your feet and toes well away from the drop zone.

Drop the Dining Chair freely and vertically with all four legs, hitting the ground, all at the

same time.

This Drop Test will help to ensure that all the Bolts and gaps reach full alignment status.

Test again for evenness on a LEVEL SURFACE.

If no wobbles are found, slowly and steadily, place the Dining Chair facedown.

Then, proceed to tighten all Bolts in a sequential manner.

When tightening the Bolts, tighten sequentially.

DO NOT tighten any Bolt fully and then move on towards the next one.

This could cause the frame to warp. If there are still wobbles, loosen the Bolts and

execute the same drop test.

If the Dining Chair is not stable, it could lead to damage to the product.

Finally, Put the Seat Cushion(D) and Back Cushion(E) on the Chair.

Page 5 OF 6

What is Proposition 65?

Proposition 65 is a California law that requires warning labels on products that may contain one of more than

800-plus chemicals or ingredients that the California Office of Environmental Health Hazard Assessment

(OEHHA) has deemed to cause cancer or other reproductive toxicity. Chemicals and elements on this list

include wood dust, brass, and other everyday substances, which can be found in very common household items,

such as: lamps, tableware, jewelry, crystal glasses, electric cords, beauty products, automobiles, and furniture.

Why Did I Find a Proposition 65 Warning on My Home Goods Product?

We include Proposition 65 warnings on all of our products because there is always a chance that one of the 800-

plus common chemicals and ingredients listed under this law could potentially be on our furniture or packing

materials. We risk large fines under this law, if we don't include this warning.

Should I worry?

We realize you may be worried finding this warning on our products, but we want to reassure you that the

hazardous exposure limits for any of these chemicals have never been found on furniture products that we’ve

shipped to our customers. Additionally, this warning label is very common and can be found on almost every

piece of furniture sold in the state of California.

Just How Common Are Proposition 65 Warnings?

Proposition 65 warnings have become so common in California that it is hard to take a trip to a local bank,

grocery store, or restaurant without finding at least one warning. In fact, even the Disney Land Resort has a

Proposition 65 warning:

Do not clean furniture with harsh cleansers or polish.

Do not put hot items directly on furniture surface

Do not write on furniture without a padded barrier to protect the surface.

To obtain the longest lifespan of your outdoor products, avoid extended and

lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the

product and /or place under patio or awnings.

To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct

sunlight is recommended.

Not for commercial use. For residential use only .

Stains may be removed with mild soap solution and damp cloth.

Dust and pick-up spills using a clean, non-colored, lint-free cloth .

Children should not climb or jump on the furniture.

Keep away from sources of ignition.

Page 6 OF 6

Label Picture Description QTY

A Seat Panel 1

B Cushion 1

C

Front / Back Leg 4

Caution: You must read this before you proceed

Chaise Lounge

CAUTION : This Lounge is NOT a TOY.

Keep your child / children at bay during the assembly process.

Page 1 OF 5

D

Middle Leg 2

Label Picture Description QTY

E Allen Key (M6) 1

F Bolt (M6*25MM) 14

Before Beginning Assembly:

Page 2 OF 5

Attach Front and Back Legs(C) to the Seat Panel(A) using Bolts(F) with Allen Key(E) as pictured above.

Do not fully tighten the Bolts.

Note: The larger Edge on the Legs should face towards the inside of the Seat Panel.

Step 2

This Lounge has multiple parts and may require up to 30 minutes to assemble. To give you an overview of

the Lounge parts, the above picture is to help you put the various parts into perspective. Please read

through the instructions below to familiarise yourself with the parts and steps before assembly.

Step 1

Unpack all parts and place on a clean, non-marring surface.

Unfold Seat Panel(A), the place it facedown on the floor.

The Lounge parts are large and heavy, always have a second Adult to assist you whenever lifting

or moving them.

When unfolding the Lounge Seat, be careful to keep hands away from the center.

Overview

Seat Panel(A)

Back Leg(C)

Middle Leg(D)

Front Leg(C)

Cushion(B)

FRONT FACING

Page 3 OF 5

Step 4

Step 5

Step 3

Attach Middle Legs(D) to the Seat Panel(A) using Bolts(F) with Allen Key(E).

Do not fully tighten the Bolts.

Note: The larger Edge on the Legs should face towards the inside of the Seat Panel.

Stand the Lounge right side up onto a flat surface and adjust to achieve levelness.

Then, fully tighten all Bolts at all joints.

Place the Cushion(B) on the Chaise Lounge.

Your Chaise Lounge is ready for use.

This Chaise Lounge can be only used on a flat, level surface.

Cushion(B)

Page 4 OF 5

Page 5 OF 5

Label Picture Description QTY

A Backrest with Leg 1

B Left Panel with Leg 1

C Right Panel with Leg 1

Caution : You must read this before you proceed

Armless Chair

Noble House Home Furnishings LLC

Page 1 OF 6

D Seat 1

E Back Cushion 1

F Seat Cushion 1

Label Picture Description QTY

①

Bolt Cap 11

②

Bolt (M6*45mm) 11

③

Washer 11

④

Spring Washer

(Ø16*2mm)

11

⑤

Allen Key 1

Before Beginning

Assembly:

Noble House Home Furnishings LLC

Page 2 OF 6

Step 1

Open the carton and place all part on a clean and soft surface.

Place the Backrest with Leg(A) against the Right Panel with Leg(C) as shown above.

Attach the Backrest with Leg(A) to Right Panel with Leg(C) using the Bolts(②), Spring Washers(④)

and Washers(③) with Alley Key(⑤).

Do not fully tighten the bolts.

Over View

This Armless Chair has multiple parts and may require up to 30 minutes to assemble. To give you an

overview of the Armless Chair parts, the above picture is to help you put the various parts into

perspective. Please read through the instructions below to familiarise yourself with the parts and steps

before assembly.

Backrest with Leg(A)

Left Panel with Leg (B)

Right Panel with Leg(C)

Seat(D)

Seat Cushion(F)

Back Cushion(E)

Noble House Home Furnishings LLC

Page 3 OF 6

Place the Left Panel with Leg(B) facedown on the clean and soft suface.

With the help of your adult partner, place the Backrest with Leg(A) against Left Panel with Leg(B).

Attach the Left Panel with Leg(B) to Seat(D) and Backrest with Leg(A) using Bolts(②), Spring

Washers(④) and Washers(③) with Alley Key(⑤).

Tighten all Bolts at all joints completely at this stage.

Attach the Seat(D) to Right Panel with Leg(C) using Bolts(②), Spring Washers(④) and Washers(③)

with Allen Key(⑤).

Do not fully tighten the bolts.

Step 3

Step 2

Noble House Home Furnishings LLC

Page 4 OF 6

Place the Seat Cushion(F) and Back Cushion(E) on the Armless Chair.

Your Armless Chair is ready for use.

This Armless Chair can only be used on a flat, level surface.

Step 4

Turn the Armless Chair face down on the clean, non-marring surface.

Use the Bolt Cap(①) to cover all Bolts.

Step 5

Place the Armless Chair on a level surface to check the wobbles.

If the Armless Chair wobbles, adjust the Levelers on the bottom of the Legs to make it level.

Step 6

Noble House Home Furnishings LLC

Page 5 OF 6

Noble House Home Furnishings LLC

Page 6 OF 6

Label Picture Description QTY

G Backrest with Leg 1

H Left Armrest with Leg 1

Caution : You must read this before you proceed

Left Armchair

Noble House Home Furnishings LLC

Page 1 OF 7

I Right Panel with Leg 1

J Seat 1

E Back Cushion 1

F Seat Cushion 1

Label Picture Description QTY

① Bolt Cap 11

②

Bolt (M6*45mm) 11

③

Washer 11

④

Spring Washer

(Ø16*2mm)

11

⑤

Allen Key 1

Noble House Home Furnishings LLC

Page 2 OF 7

Overview

This Armchair has multiple parts and may require up to 30 minutes to assemble. To give you an overview

of the Armchair parts, the above picture is to help you put the various parts into perspective. Please read

through the instructions below to familiarise yourself with the parts and steps before assembly.

Before Beginning

Assembly:

Left Armrest with Leg(H)

Backrest with Leg (G)

Seat (J)

Right Panel with Leg (I)

Back Cushion (E)

Seat Cushion (F)

Noble House Home Furnishings LLC

Page 3 OF 7

Page is loading ...

Noble House 300395 Operating instructions

This manual is also suitable for

Noble House 300395 Operating instructions

Related papers

Other documents