Ariens 917011 Operating instructions

Ariens
Brand
Ariens
Model
917011
Type
Operating instructions

Ariens 917011 Below you will find brief product information for Ariens 917011. It's a log splitter well-suited for home and farm use, with a 30-ton splitting force. The Ariens 917011 is powered by a 13HP Briggs & Stratton engine. It features a 2-stage pump, auto-return valve, and a 20-second cycle time for increased productivity. The low-profile design makes it easy to load logs and features a 22.5" working height. Additional features include a hydraulic oil cooler and a 4-way wedge that can be adjusted to accommodate logs of various sizes and shapes.

Ariens 917011 Below you will find brief product information for Ariens 917011. It's a log splitter well-suited for home and farm use, with a 30-ton splitting force. The Ariens 917011 is powered by a 13HP Briggs & Stratton engine. It features a 2-stage pump, auto-return valve, and a 20-second cycle time for increased productivity. The low-profile design makes it easy to load logs and features a 22.5" working height. Additional features include a hydraulic oil cooler and a 4-way wedge that can be adjusted to accommodate logs of various sizes and shapes.

EN - 1
Log Splitter
Setup Instructions
Instructions Pour La Mise En Place
Instrucciones Para Su Montaje
IDENTIFICATION
1. Draw Bar
2. 1/2 x 1" Hex Bolt (4)
3. 1/2" Hex Nut (4)
4. P-Clamp
5. Safety Chain
6. Front Stand
7. Front Stand Lock Pin
8. Hydraulic Cylinder
9. Control Lever
10. Splitter Wedge
11. Beam
12. Rear Stabilizer
13. Stripper Plate
14. Beam Lock
15. Clevis Pin
16. Cotter Pin
17. Control Valve
18. ISO 32 Hydraulic Fluid (part # 00069100) – Not Included
19. 3/8 x 1" Hex Bolt (1)
20. 3/8" Hex Nut (1)
1
10
9
6
5
3
2
18
11
17
12
13
14
7
15
16
4
8
Not
Included
19
20
© Copyright 2013 Ariens Company
02/13
04582200A
Tools Required:
• Two 3/4" wrenches or sockets
• Two 9/16" wrenches or sockets
• One 1/2" wrench or socket
• One 3/8" wrench or socket
• Thin-nosed pliers
• Wire cutters
EN - 2
ASSEMBLY
Remove crate top and sides. Remove shipping bag and
cut straps retaining unit to crate bottom. DO NOT cut
cable ties retaining cylinder to beam.
Support draw bar (# 1). Remove and dispose of four 1/4 x
1/2" Taptite bolts retaining draw bar to frame.
a. Fold front stand (# 6) down and lock in place with
lock pin (# 7).
b. Position draw bar in frame and attach using four
1/2 x 1" hex bolts (# 2) and four 1/2" hex nuts (#
3). Insert bolts from inside of frame with hex nuts
on the outside. Make sure that front stand is
facing down before attaching.
WARNING: AVOID INJURY. Read and
understand the entire Safety section in the
Owner’s Manual before proceeding.
DO NOT start engine until instructed and all
assembly steps have been completed.
1.
Do NOT cut.
Cut straps.
2.
3.
1
Remove and
dispose.
2, 3
EN - 3
Ensure that beam lock (# 14) is seated in hole and rotate
beam (# 11) into horizontal position until it locks into
position. Lock must engages fully.
Remove three hex bolts retaining stripper plate (# 13)
from each side and remove stripper plates. Retain for
installation.
a. Remove hair pin, washer, and clevis pin retaining
wedge (# 10) to hydraulic cylinder. Retain for
assembly.
b. Slide wedge away from hydraulic cylinder.
c. Cut cable ties retaining cylinder to beam.
Position hydraulic cylinder into the beam yokes and
install one stripper plate.
4.
5.
14
11
13
6.
CAUTION: Avoid Injury! Keep hands and
fingers clear. Cylinder assembly will drop
slightly when clevis pin is removed.
7.
Washer
15
Hair Pin
10
Position cylinder
in yokes.
EN - 4
Slide wedge back to cylinder and reinstall clevis pin,
washer and hair pin.
a. Remove the cotter pin (# 16) and clevis pin (#
15) from the control lever (# 9).
b. Rotate control lever up to control valve and
reinsert the clevis pin.
c. Insert cotter pin back into clevis pin and spread
ends outward.
d. Install remaining stripper plate.
a. Attach hydraulic hose to draw bar using P-clamp
(# 4), 3/8 x 1" hex bolt (# 19) and hex nut (# 20).
b. Roll unit off of crate bottom.
a. Add ISO 32 hydraulic fluid (# 18) to reservoir.
See owner’s manual.
b. Check engine oil level and add if necessary. See
engine manual.
c. Add fuel and start engine and allow to warm up.
See engine manual and owners manual.
d. Fully extend and retract cylinder 3 or 4 times.
e. Stop engine.
f. Check hydraulic fluid level on dipstick and add
more fluid if necessary.
8.
9.
Install clevis pin, washer and hair pin.
Rotate
lever up.
15, 16
9
10.
11.
WARNING: AVOID INJURY. DO NOT
proceed until operation and safety rules
are fully understood.
Read and understand the entire Owner’s
Manual before proceeding.
19, 20
4
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Ariens 917011 Operating instructions

Ariens
Brand
Ariens
Model
917011
Type
Operating instructions

Ariens 917011 Below you will find brief product information for Ariens 917011. It's a log splitter well-suited for home and farm use, with a 30-ton splitting force. The Ariens 917011 is powered by a 13HP Briggs & Stratton engine. It features a 2-stage pump, auto-return valve, and a 20-second cycle time for increased productivity. The low-profile design makes it easy to load logs and features a 22.5" working height. Additional features include a hydraulic oil cooler and a 4-way wedge that can be adjusted to accommodate logs of various sizes and shapes.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages

Related papers

Other documents