Desktop Power Center
I N S T A L L A T I O N I N S T R U C T I O N S
I
nstallation Instruction No.: 1 009 456 – August 2010
Legrand/Wiremold electrical systems conform to and should be
properly grounded in compliance with requirements of the current
National Electrical Code or codes administered by local authorities.
All electrical products may present a possible shock or fire
hazard if improperly installed or used. Legrand/Wiremold electrical
products may bear the mark as UL Listed and/or Classified and
should be installed in conformance with current local and/or the
National Electrical Code.
NOTE: Part Numbers WSR320-S and WSR400-S are for residential use only.
Step 1. Remove Mounting Plate (A) from Power Unit (B).
Depress
Tab
PART NUMBERS: WSC320-S, WSC400-S, WSR320-S, WSR400-S
HOLE MOUNT
Depress
Tab
Step 2. Insert Hole Mount (C)
into Mounting Plate
(A) and into Desk.
A
B
Use bushing only in
holes that are larger
than 2 1/4" [57mm].
Maximum hole size
is 3" [76mm].
Step 3. Secure to Desk.
Step 4. Feed Power Cord through Hole. Mount and hook front
slots (A) of Power Unit to Mount Clips (B).
Step 5. Attach Power Unit to Mount.
Snap together
two Tabs
W A R N IN G!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below may result
i
n electric shock, fire, and/or serious injury.
SAVE THESE INSTRUCTIONS
1. Grounded electrical products must be plugged into
an outlet that is properly installed and grounded in
accordance with all codes and ordinances. Never
remove the grounding prong or modify the plug in
any way. Do not use any adapter plugs. Check with
a qualified electrician if you are in doubt as to
whether the outlet is properly grounded.
2. Do not expose this product to rain, wet or damp
conditions. Water entering this product will increase
the risk of electric shock.
3. Do not abuse the power cord. Keep the power
cord away from heat, oil, sharp edges, or moving
parts. If power cord becomes damaged, replace
the product.
4. This product must be properly installed before
connecting to the power supply
5. Do not use this product in combination with an
extension cord.
Power Unit
(B)
Mounting
Plate (A)
Hole Mount
(C)
Mounting
Plate (A)
Tighten Screws
Wiremold
U.S. and International:
60 Woodlawn Street • West Hartford, CT 06110
1-800-621-0049 • FAX 860-232-2062 • Outside U.S.: 860-233-6251
Canada:
570 Applewood Crescent • Vaughan, Ontario L4K 4B4
1-800-723-5175 • FAX 905-738-9721
1 009 456 0710
© Copyright 2010 Legrand/Wiremold All Rights Reserved
EDGE MOUNT
NOTE: This part is not needed
for edge mounting.
Step 2. Remove Hole Mount (C).
Step 3. Assemble Edge Mount (D). Step 4. Attach Edge Mount to Desk.
Step 5. Attach Power Unit to Mount.
Snap together
two tabs
Step 1. Remove Mounting Plate (A) from Power Unit (B).
Depress
Tab
Depress
Tab
Power Unit
(B)
Mounting
Plate (A)
Hole Mount
(C)
Edge Mount
(D)
-
1
-
2
Legrand WSR320-S User manual
- Category
- Surge protectors
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Legrand Nonmetallic Wall-Mounted Wireless Access Point Enclosure - NME1250AP Installation guide
-
-
-
-
Legrand Cable Management Box Installation guide
-
-
-
-
-