Interphone Urban User manual

Brand: Interphone

Model: Urban

Category: GPS receiver modules

Type: User manual

Interphone Urban is a wireless Bluetooth helmet device that allows for communication and entertainment while riding a motorcycle. With a quick-release bracket, it easily attaches to most helmets. It offers intercom functionality for rider-to-passenger communication, as well as connectivity to two devices like mobile phones or GPS navigators simultaneously. Enjoy music from Bluetooth devices with A2DP and AVRCP profiles. Listen to FM radio with RDS and store up to 8 stations. Voice prompts and a Quick touch interface with direct access buttons make it user-friendly.

USER GUIDE

Chap. 1 - Introduction 3

1.1 Presentation 3

1.2 Warnings 3

1.3 Main specifications 3

1.4 Package contents 3

Chap. 2 - Getting started 4

2.1 Installation instructions 4

2.2 Main commands 4

2.3 - Battery charging 5

2.4 LED indication 5

2.5 Initial ignition (only dual unit version) 5

2.6 Initial ignition (only single unit version) 5

2.7 Voice guide language setting: 5

2.8 Listening priority 5

Chap. 3 - Settings 6

3.1 System settings 6

Chap. 4 – Intercom 6

4.1 Pairing 6

4.1.1: Manual pairing 6

4.1.2: Pairing to a PREVIOUS SERIES INTERCOM device 6

4.1.3: Pairing with a NON-Interphone (ANYCOM™) device 6

4.2 Two-unit intercom conversation 6

4.3 Warnings and suggestions 6

Chap. 5 - Phone/GPS 7

5.1 Pairing 7

5.2 Telephone use 7

5.3 Warnings and tips for using the phone 7

5.4 GPS 7

Chap. 6 – FM RADIO 8

6.1 Listening to FM radio 8

6.2 “FM radio” function warnings and suggestions 8

Chap. 7 - Music 8

7.1 Playing music 8

7.2 Sharing music 8

7.3 “MUSIC” function warnings and suggestions 8



1.1 Presentation

Thank you for choosing this product. URBAN Interphone is a Bluetooth® helmet device for wireless

entertainment and communication between multiple motorcyclists.

URBAN Interphone can be installed on most helmets with a quick attachment/detachment bracket.

URBAN Interphone is certified to withstand harsh weather, with “IP67” protection level.

1.2 Warnings



Fully charge the battery before using the product for the first time.

Do not store the Product without charging it. Failure to do so may cause irreversible damage to the

battery capacity. Charge the battery every TWO months.



The external unit (control unit), connected to the audio kit, is classified IP67 according to the IEC60529

standard. The control unit, connected to the audio kit, can therefore be immersed in a metre of fresh

water for a maximum of 30 (thirty) minutes.

Despite this classification, the device is not immune to greater stress, such as prolonged immersions or

high pressure water jets.

Using the product during intense meteorological phenomena, at high speeds, may be equivalent to

subjecting the product to a high pressure jet.



Do not immerse the product in fresh water which is more than a metre deep for more than 30 minutes.

Do not store the product when still wet: dry it with a clean, soft cloth. Dry any water or moisture present

in the connector of the control unit and/or audio kit with hot air for at least 10 minutes, so as to prevent

the oxidation of the contacts.

Do not expose the product to salt water or ionised water, drinks or other liquids. If the device is exposed

to liquids other than fresh water, wash the device with cold fresh water and dry it carefully with a clean,

soft cloth.

Do not expose the product to high pressure water jets.

Make sure that the audio kit connector is completely inserted in the control unit. If not, complete pro-

tection against water and dust is not guaranteed.

1.3 Main specifications

URBAN Interphone allows communication rider-passenger.

 URBAN Interphone can be connected simultaneously to a maximum of two devices

(mobile phone/GPS navigators).

 URBAN Interphone has an integrated FM-RDS receiver for the 88-108 MHz band. It is possi-

ble to store up to 8 stations.

 URBAN Interphone can play music from Bluetooth® devices, through A2DP and AVRCP profiles

(smartphones, MP3 player etc.).

 URBAN Interphone features a Quick touch™ interface consisting of four keys for direct

access to the functions. The single pressing of a button will activate the corresponding function, quickly

and intuitively, without the need for a menu.

1.4 Package contents

In the dual version, the material shown in the red box is present in the quantities of two pieces for each

component.

X 2

Microphone for full face helmet

Speaker kit

Microphone for ip-up/jet helmet

USB cable for charging and data

Velcro and spare sponges

Clamp bracketAdhesive bracket





Follow the sequence shown in the figures below for installation of the components.

2.2 Main commands

Locate the area in correspondence

with the ear

If possible, remove the two

cushions or padding

Position the strips of Velcro

for the speakers

Filp-up/jet helmet Full face helmet

Choose the microphone to use:

Place the speakers

music

Phone

Bluetooth Unit

Volume +

Volume -

Led

Music

FM Radio

Up (<)

Down (>)

Intercom / On-O

Power On Press until the blue LED comes on

Power Off Hold pressed until the red LED comes on and

the device turns off

 Press the buttons “Volume +” to increase and

“Volume –” to decrease the volume.

Intercom, FM radio, phone and music functions Press to directly activate (or deactivate) the

intercom communication.

Press

to directly activate (or deactivate) FM

radio.

Press to directly access the functions of the

phone.

Press

music

to directly activate (or deactivate) the

playing of music.

These commands are via direct access. It is

therefore possible to move from one function to

another with the pressing of a button. It is not

necessary to disable a function before moving

on to another.

2.3 - Battery charging

Insert the micro USB charging cable into the relevant intercom connector, as shown in the figure. Con-

nect the cable to a standard USB charger.

LED indications:

- red LED: charging.

- mgreen LED: fully charged.

2.4 LED indication

Standby The BLUE LED flashes approximately every 3

seconds.

Intercom active The LED turns BLUE with button intensity.

Device connected with phone/GPS The LED emits a double BLUE flash approxima-

tely every 3 seconds.

 The LED emits an alternate BLUE flash.

Device in pairing mode The LED flashes RED/BLUE alternately.

 The LED flashes RED/BLUE rapidly and alternately.

 The LED lights up PURPLE.

Charging The LED comes on RED during charging. The LED

comes on GREEN when charging is complete.

Dead battery The LED lights up RED.



Press on both the units to switch on the devices. The units are already paired by default.



Press to turn the unit on. The device will go into “PAIRING MODE”. These are the possible choices:

- pairing with Cellularline Interphone devices (see chapter 4.1).

- pairing with intercoms of other manufacturers (see chapter 4.1.4).

- phone or GPS navigation pairing (see chapter 5.1).



• With the device turned on, press and hold the UP button (<) until the third beep. The LED will be purple.

• Press + to select the desired language.

• Keep pressing the UP button (<) until the third beep to save the selection. The LED will flash blue.

2.8 Listening priority

The device uses the following priorities in managing the various functions:

1. Mobile phone

2. Intercom (communication with other intercoms)

3. Bluetooth® A2DP audio source (Music from smartphone/Google Maps, MP3 Player etc.)

4. FM radio

This sequence is used by the device to manage the simultaneous use of multiple functions and to cho-

ose which function to stop.

Examples:

• if a call is received while listening to music, the latter will be interrupted, automatically switching to

the phone audio.

• If an intercom call is received while engaged in a phone call, the latter will not be interrupted.





With the device turned on, press and hold the UP button (<) until the third beep. The LED will be purple.



Pressing each button will change a parameter, according to the figure shown below.



To save the parameters set simply exit the settings mode by keeping pressed the UP button (<) until the

third beep. The LED will flash blue.

3.1 System settings

each press of the button selects a different language for the voice guidance.

the device can automatically adjust the listening volume,

depending on the type of helmet being used. The function can be completely disabled, in which case

the user will manually adjust the volume. The maximum audio level possible can be obtained with the

AUTOMATIC VOLUME OFF.

 press this button for 5 seconds to delete from the memory all previously paired

Bluetooth devices. When erasing the pairings, exiting the Settings mode, the device will automatically

enter pairing mode, shown in Chap. 2.6.

this service allows the device to tune to an alternative frequency when the signal beco-

mes too weak. Each press of the button activates/deactivates the function.

 Where a phone call is received, it is possible to answer the call with a simple voice

command. This function can be switched on/off.



The device enables the interphone communication (function named “INTERCOM”) across multiple devi-

ces in conference (several people talking at once).

4.1 Pairing

Before starting the communication between intercoms it is necessary to perform pairing of the various

devices. This process will only need to be performed once.

Subsequently the interphone will automatically recognise the previously paired devices.

URBAN Interphone is compatible with the entire INTERPHONE range (including the previous series) and

with the ANYCOM function. It is also compatible with the interphones of other manufacturers.

Each URBAN Interphone can be paired to a maximum of two intercoms.

If a device already has two intercoms paired, performing a third pairing with erase the pairing

with the first device paired.



1. With the intercom off, on each unit, press and hold until the LED flashes red/blue.

2. Then briefly press only on one of the two units.



1. With the second Interphone unit (previous series) off, press and hold the central MFB button until

alternate red/blue flashing of the LEDs.

2. With URBAN Interphone off, press and hold until the LED flashes red/blue.

3. Press briefly on URBAN Interphone.

4.After a few seconds the units will be paired and the intercom conversation will be started.



1. In the NON-Interphone unit, start the telephone search/pairing mode; refer to the user manual of the

intercom to be paired.

2. With URBAN Interphone off, press and hold until the LED flashes red/blue.

3. Press on URBAN Interphone.

4. After a few seconds the units will be paired and the intercom conversation will be started.



1. Pair unit 1 with unit 2 (Chap. 4.1.1), operation only required the first time.

2. Press briefly on unit 1 or on unit 2.

3. Press again briefly on unit 1 or on unit 2 to interrupt the communication.

4.3 Warnings and suggestions

During use in three/four user conference, to ensure the best system stability, avoid connecting other

Bluetooth® devices (telephones, GPS, etc.) to the intercom units.

music

Voice telephone

response On/O

Bluetooth Unit

Selezione lingua

Guida vocale

RDS

On/O

Automatic volume

Integral/Jet/O

Erase pairings

(5” press)

1 2

music



URBAN Interphone can be connected to Bluetooth® devices, such as mobile phones, GPS and MP3

players.

Every URBAN Interphone can be connected simultaneously to up to two Bluetooth® devices (with the

exception of using the three- or four-unit INTERCOM function as described in Chap. 4.3/4.4).

5.1 Pairing

Before starting use of URBAN Interphone with these devices, it is necessary to perform pairing of the

various devices. This process need only be performed once. Subsequently URBAN Interphone will auto-

matically recognise the devices previously paired and will automatically connect.

Pairing procedure

1) Activate the Bluetooth® function on the phone/GPS/MP3 (refer to the device manual for further de-

tails).

2) With URBAN Interphone in Standby mode (BLUE LED flashing), press together the buttons + + for

3 seconds to activate “PAIRING mode” (BLUE and RED flashing).

3) Start searching for new Bluetooth® devices on the mobile phone / GPS / MP3 reader

4) After a few seconds the device will show “F6T”. Select this option.

5) If prompted for a PIN or code, enter 0000 (four zeros).

6) The voice guide will confirm successful pairing with the message “SUCCESSFUL PAIRING, CONNECTED

TO THE PHONE”. The device will go into Standby mode (blue LED flashes twice every 3 seconds).

7) If the Bluetooth® device requires authorisation to access the list, provide confirmation.

To pair a second device, repeat the procedure from step 1).



As specified in section 2.8, a phone call has the highest priority than any other URBAN INTERPHONE

function. In case of receipt of a phone call use the commands shown in the following table:

 In case of an incoming call, press the button

or say a word out loud (voice activated response

Chap. 3.1)

 To end a call press the button or wait for the

other person to end the call.

 Press to activate the voice call

 Press the button until the beep (1.5 seconds)

to redial the last number.

 Press the button until the second beep (3

seconds) to call the number set.

5.3 Warnings and tips for using the phone

If two different mobiles are connected at the same time, the functions “Redial last number” and “Voice

call” may only be used by the first phone connected.

An Internet connection on the mobile phone may be needed to use the “Voice call”.

The “Voice call” function may not be supported by your mobile phone (refer to your device manual for

further details).

5.4 GPS

After pairing the URBAN Interphone to the GPS (Chap. 5.1) it is possible to hear the voice prompts sent

by the navigator. During the intercom communication the GPS (if fitted) will interrupt the conversation

whenever it is necessary to transmit a voice prompt.

 ensure the GPS is compatible with the Bluetooth® headsets. Consult the GPS user

manual for further information.

URBAN Interphone uses the Bluetooth® HFP profile to manage the connection to a GPS unit.

Navigators integrated within smartphones use the A2DP profile to send route directions. This profile

does not allow interruption of the intercom conversation.

Navigators sold for use in cars are NOT usually equipped with Bluetooth® HFP. For that reason they

cannot transmit voice prompts to Bluetooth® headsets. Consult the GPS user manual for further infor-

mation.

CHAP. 6 – FM RADIO

URBAN Interphone has integrated FM radio with RDS and 8 stations that can be saved

6.1 Listening to FM radio

Radio on/off Press the

button.

Forward/backward station search Press the UP/DOWN button to start the forward/

backward search (from 88 MHz to 108 MHz) for

a station.

 Press the UP button until the beep to select the

next saved station.

Press the DOWN button until the beep to select

the previous saved station.

Saving a station Press the button

until the beep (1.5 seconds)

to save the station being listened to.

Press the UP or DOWN button to select the me-

mory (from no. 1 to no. 8) to save the station.

Press the button

to confirm the memory

(from no. 1 to no. 8).

Automatic Saving

 Press the button

until the beep (3 seconds) to

save the 8 stations with the optimum frequency

Saving is temporary and the stations will be de-

leted when the URBAN Interphone is restarted.

6.3 “FM radio” function warnings and suggestions.

URBAN Interphone has an FM receiver with RDS. This feature is used:

• when the tuned broadcast signal becomes too weak, URBAN Interphone will attempt to tune in to an

alternative frequency used by the same station.

• when the device is tuned in to a radio station, the voice guide will announce the frequency and the

name of the broadcaster.

In case the signal of the current station is not weak enough to trigger the search for an alter-

native station, it is possible that listening will be characterised by disturbances due to poor

signal strength. FM reception is strongly influenced by the surrounding environment (electro-

magnetic disturbances, natural obstacles etc.).



URBAN Interphone can play music from Bluetooth® devices (smartphones, MP3 players etc.) equipped

with A2DP profile. To play music it is necessary to pair the devices to URBAN INTERPHONE (Chap. 5.1)



 Press the

music

button to start/stop playback of

music

 Press the UP or DOWN button to select the next

or previous track.

7.2 Sharing music

URBAN Interphone has a “SONG SHARING” function which allows music sharing with another Interpho-

ne.

Start/Stop sharing Press the UP button until the second beep to

start/stop music sharing with Interphone 3.

Press the DOWN button until the second beep to

start/stop music sharing with Interphone 1.

During music sharing, by pressing the button it is possible to start an intercom communication.

7.3 “MUSIC” function warnings and suggestions.

• Only Bluetooth® devices with A2DP profile can transmit stereo music to the device.

• Only Bluetooth® devices with AVRCP profile can be controlled at a distance from the device.

• The sound quality of the music also depends on the quality of the audio source (bitrate and codec of

audio files, Bluetooth® player quality etc.).

1 2 3

music

DOWN



Bluetooth® compliance: Bluetooth® v. 4.2 - Classe II

Supported Bluetooth profiles: HFP / A2DP / AVRCP

Dimensions mm: 55x85x25

Weight: 68 g

Capacity: Up to 10 metres

Talk time: 20h

Stand-by time: 1000 h

Charging time: 1,5 h

Battery type: Lithium-ion rechargeable

DOWN

INSTRUCTIONS FOR THE DISPOSAL OF APPLIANCES FOR DOMESTIC USERS

(Applicable in countries in the European Union and in those with separate waste collection systems)

This mark on the product or documentation indicates that this product must not be disposed of with

other household waste at the end of its life. To avoid any damage to health or the environment due to

improper disposal of waste, the user must separate this product from other types of waste and recycle

it in a responsible manner to promote the sustainable re-use of the material resources.

Domestic users should contact the dealer where they purchased the product or the local government

office for all the information regarding separate waste collection and recycling for this type of product.

Corporate users should contact the supplier and verify the terms and conditions in the purchase con-

tract. This product must not be mixed with other commercial waste or disposed of together with other

commercial waste.

This product has a battery than cannot be replaced by the user. Do not attempt to open the device to re-

move the battery as this could cause malfunctions and seriously damage the product. When disposing

of the product, please contact the local waste disposal authority to remove the battery. The battery

inside the device was designed to be able to be used during the entire life cycle of the product.

This product is CE marked in accordance with the provisions of Directive R&TTE (1999/05/EC) and of Di-

rective ROHS (2011/65/EU). With this, Cellular Italia S.p.A. declares that this product complies with the

essential requirements and other relevant provisions of Directive 1999/5/EC and Directive 2011/65/

EU. The user is prohibited from making any type of change or variation to the device. Variations or chan-

ges not expressly approved by Cellular Italia S.p.A will cancel the user’s authorisation to use the device.

Bluetooth® is a trademark owned by Bluetooth SIG, Inc.

For further information, visit the website www.interphone.com

Interphone Urban User manual

Brand: Interphone

Model: Urban

Category: GPS receiver modules

Type: User manual

Download PDF

report

Interphone Urban User manual

Interphone Urban User manual

Related papers

Other documents