INSTALLATION GUIDE FOR
UBI SENSOR FRAME
Ubi Interactive Inc.
www.ubi-interactive.com
Ubi Interactive Inc.
Contents
INTRODUCTION ................................................................................................................................................................. 2
WHAT IS IN THE PACKAGE ............................................................................................................................................. 2
HOW TO SET UP HARDWARE ......................................................................................................................................... 2
INTERACTION ..................................................................................................................................................................... 6
SETTING UP UBI APPS ..................................................................................................................................................... 7
Ubi Interactive Inc.
INTRODUCTION
Ubi Sensor Frame is a frame that can be added to display panels of any size or technology
to make them interactive. The sensor frame is packaged with sensors that can detect very
accurately the position of your finger. It is a true plug and play solution. Snap it onto your
display panel and with no special set up or driver, your display magically turns a touch
screen.
Ubi sensor frame also comes with an array of software tools and apps.
This document provides you all the instructions to set up and use Ubi Sensor Frame.
WHAT IS IN THE PACKAGE
Each package contains the following items
HOW TO SET UP HARDWARE
• When you unpack the package, the full set of IR touch frames will look like this: For
frames larger than 90” there will be two extra pieces for each of the longer side.
There is also an additional power supply included for the larger frames. Each frame
is labeled to indicate which corners go with which one. In some of the sized, the
matching corners are coded with color.
Edges of the sensor frame
4
USB cable
1
3M Adhesive
24 strips
Screws
8
Instruction Manual
1
USB extension
Optional
Stylus
Optional
Ubi Interactive Inc.
Figure 1 : Front view of each side of the sensor frame
Figure 2 : Back view of each side of the sensor frame
Each corner of the edge has a specific color code to indicate which corners
match.
• Place the four sides of the frame in the correct position. Make sure corners with
the same color go next to each other. The longer edge with Ubi logo in the front
Figure 3: The color marker in the corner indicating matching pairs
Ubi Interactive Inc.
and USB cable on a side, go at the bottom.
• Connect the matching corners as shown below. The corners should snap together
without having to insert much pressure.
Figure 5: Snap together the matching corners
• This is how it should look once the connection is successful
Figure 4: The edges aligned together
Ubi Interactive Inc.
Figure 6: The corners once snapped together
• To make sure that the edges are connected firmly, use two screws on each corner.
Figure 7: Affix the edges by using provided screws
• After assembly, place the frame on a flat surface. Connect the USB cable to any
Windows/Lunux PC/ Mac/ Chromebit device. The frame will be automatically
Ubi Interactive Inc.
detected as an HID device. Try moving your finger inside the frame and make sure
the finger is showing up as a touch point ( or mouse in case of Mac). After testing
disconnect the USB cable.
• Now you are ready to paste the frame on the display. Use the provided tape.
Apply the strips of tape on the bezel. Lift up the assembled frame gently and affix
it agains the display panel.
• Once the frame is affixed on the display, connect the USB cable again to your
preferred device. The sensor frame should be automaticaly detected and you
should be able to interact with the content on the display now.
INTERACTION
Ubi Sensor Frame can detect up to 10 fingers simultaneously on Windows, Linux and
Android.
On Chrome OS, Ubi Sensor Frame can support multi-touch interaction. The exact
number of touch input depend on the configuration of your Chrome device and its
touch drivers.
Figure 8: Apply the tape on the bezel of the display
Ubi Interactive Inc.
Mac OS does not offer support for touch. Therefore, Ubi Sensor Frame will behave like a
mouse on these devices.
In addition to fingers, Ubi Sensor Frame also supports stylus interaction. Ubi Interactive
provides soft touch felt tip stylus upon request. The stylus can avoid finger smudges and
scratches on the display.
SETTING UP UBI APPS
Ubi sensor frame also comes with an array of software tools and apps. They include a
desktop annotation tool, a whiteboard tool, a shared web whiteboard tool and a
document camera app. You can download and install from this link http://getubi.ubi-
interactive.com/UbiApps/UbiApps_Setup.exe
A tutorial on these apps can be found here – https://forum.ubi-interactive.com/hc/en-
us/categories/201261546
We also have an education all called Freeboard that provides more advanced features for
creating classroom and training materials . You can download it from here
http://getubi.ubi-interactive.com/prod_dl/freeboard/Ubi_FreeBoard.zip
A tutorial on this app can be found here -
https://forum.ubi-interactive.com/hc/en-us/articles/115003839483-Freeboard-
Annotation-and-Whiteboard-App
TROUBLE SHOOTING
Calibrating the display in case of an offset
If your TV does not match up in size exactly with the sensor frame or you did not align
the sensor frame correctly with the TV, you may see an offset between where you touch
and where interaction happens. In order to correct this, we have a special utility. Please
download it from here and proceed as follows.
Ubi Interactive Inc.
1. Launch the utility by double clicking. A screen such as the one below will show up
2. Click on the calibration button
3. A window such as the following will appear. Touch on each marked position as
instructed. Once you touch all the four points, your offset should disappear
Using the touchscreen TV as secondary display
When you use Ubi sensor frame on a primary display it works automatically and send
the touch input to the correct display.
Ubi Interactive Inc.
However, if your Ubi sensor frame-enabled display is not a primary display, it is not that
simple. You will see that when you touch your display the touch input appears on the
primary display instead.
Please follow the instructions here
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
UBI EasyCoder 501XP Installation Instructions Manual
-
-
-
-
-
-
-
-
-
Other documents
-
Humax IR-ACE II User manual
-
Star Trac E Series Upright E-UBi Gen. 1 Owner's manual
-
Intermec EasyCoder E4 Installation & Operation Manual
-
YURAKU YUR.PHOTO 8M5W Quick start guide
-
Star Trac E-UBi User manual
-
Asus Chromebit (CS10) User manual
-
KONIX WOT GH 40 7.1 Owner's manual
-
NewLine TT-6518RS User manual
-
-
pico neo 2 A New Reality Virtual Reality All-In-One Headset User guide
