VECTRONIC Aerospace VERTEX Motion User manual

VERTEX Motion
Brand
VECTRONIC Aerospace
Model
VERTEX Motion
Type
User manual

VECTRONIC Aerospace VERTEX Motion is a versatile tool that allows you to activate, configure, and read data from your VERTEX Motion device. With this tool, you can:

  • Set the Motion's time and generate an info file with the current configuration setup.
  • Activate or deactivate data collection on the Motion.
  • Configure the Motion's sensors, including the acceleration sensor and magnetometer sensor.
  • Read data from the Motion and save it to your computer in a user-friendly format.
  • Erase specific data or all Motion data at once.

The VERTEX Motion is a powerful tool that can be used for a variety of applications, including:

VECTRONIC Aerospace VERTEX Motion is a versatile tool that allows you to activate, configure, and read data from your VERTEX Motion device. With this tool, you can:

  • Set the Motion's time and generate an info file with the current configuration setup.
  • Activate or deactivate data collection on the Motion.
  • Configure the Motion's sensors, including the acceleration sensor and magnetometer sensor.
  • Read data from the Motion and save it to your computer in a user-friendly format.
  • Erase specific data or all Motion data at once.

The VERTEX Motion is a powerful tool that can be used for a variety of applications, including:

VERTEX Motion Communication Tool
User Manual
Download: https://www.vectronic-aerospace.com/downloads/#software
VECTRONIC delivers the VERTEX Motion with its pre-defined configurations. Before
deployment it only must be activated. The tool is to activate the Motion, view its information,
change configurations and read/erase its data.
1. Download and run Vertex_Motion_com_Tool.exe and go through the setup to install the
tool.
2. Connect VERTEX Motion via USB-cable (USB to 4-pin header, delivered from VECTRONIC).
3. Open Device Manager and get Motions COM-Port ID (COMx)
4. Tool Overview:
5. Connect Motion to the software (Basic Command area):
1. Press ‘R’ to update connected COM-Devices
2. Choose COM-Port
3. Press ‘connect’
After successfully connecting the Motion, Motion’s information and configuration are
shown in the according area.
• Reload: Reloads Motion information.
• Set Time and generate Info file: Sets Motion time to current PC time. In case the
checkbox ‘Generate Info File’ is selected, Motion’s Info file with current configuration
setup is stored in user’s documents folder.
• Activate/Deactivate VERTEX Motion: enable/disable data collect of the VERTEX Motion.
Before you deploy the VERTEX Motion: Press ‘Activate Motion’ and check whether the
state ‘active’ is shown in the ‘Motion Info area’.
6. Motion Info area: Displays Motion information
7. Motion Configuration area: Displays configuration and activation of all Motion sensors.
• Acc.: Acceleration Sensor- select acc. Data sample rate (10, 25, 50Hz) and measurement
range (± 2, 4, 8, 16g).
• Mag.: Magnetometer sensor- select sample rate (10, 20, 50Hz) and resolution (Full: 16
Bit data sample resolution / Half: 8 Bit data sample resolution).
• Written sector: Used data storage of according sensor.
Whenever you make changes to the configurations, press ‘Update Configs’ in order to
apply the new settings.
8. Data area:
Read data and save files automatically to user’s document folder.
9. In case of reading data error:
If an error occurs while reading data, an error message is shown inside the black log
window. (In the example above no error occurs (‘End Read Mag. Data without errors’).
In case of an error you do not have to load all data from the beginning, you can set the
Loading Block (Start Block) to the number before the error occurs. When continuing
data download after an error, an additional file data file will be created.
10. Erase either specific data or all Motion data at once.
Note: The Motion only collects data if it is activated and sensors are enabled by
according Device Config setting. Activate the Motion in the Basic Commands area.
Note: Keep the Collar magnet and Drop Off magnet away from the Motion. If they
are too close, the magnets may cause damage to the Motion.
VECTRONIC Aerospace GmbH
wildlife@vectronic‐aerospace.com
Carl‐Scheele‐Str. 12
www.vectronic‐aerospace.com
12489 Berlin
Phone:
+49 30 6789 4990
Germany
Fax:
+49 30 6789 5230
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

VECTRONIC Aerospace VERTEX Motion User manual

VERTEX Motion
Brand
VECTRONIC Aerospace
Model
VERTEX Motion
Type
User manual

VECTRONIC Aerospace VERTEX Motion is a versatile tool that allows you to activate, configure, and read data from your VERTEX Motion device. With this tool, you can:

  • Set the Motion's time and generate an info file with the current configuration setup.
  • Activate or deactivate data collection on the Motion.
  • Configure the Motion's sensors, including the acceleration sensor and magnetometer sensor.
  • Read data from the Motion and save it to your computer in a user-friendly format.
  • Erase specific data or all Motion data at once.

The VERTEX Motion is a powerful tool that can be used for a variety of applications, including:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents