Linortek Master-Slave User guide

Master-Slave
Brand
Linortek
Model
Master-Slave
Type
User guide

Linortek Master-Slave is a versatile device that allows you to create a remote control system for your electrical appliances. With the Master-Slave setup, you can control multiple slave devices from a single master controller over the internet. This feature is useful for automating and remotely managing devices in different locations, such as turning on lights, activating security systems, or controlling irrigation systems.

Here are some key capabilities of the Linortek Master-Slave:

  • Remote control: Link multiple slave devices to a master controller using their IP addresses and control them remotely from anywhere with an internet connection.

Linortek Master-Slave is a versatile device that allows you to create a remote control system for your electrical appliances. With the Master-Slave setup, you can control multiple slave devices from a single master controller over the internet. This feature is useful for automating and remotely managing devices in different locations, such as turning on lights, activating security systems, or controlling irrigation systems.

Here are some key capabilities of the Linortek Master-Slave:

  • Remote control: Link multiple slave devices to a master controller using their IP addresses and control them remotely from anywhere with an internet connection.
MASTERSLAVEDEVICESETTINGINSTRUCTIONS
EachLinortekwebrelaycontrollerincludesaremotefunctionthatcandeliverasignalfromamastercontrollertoremoteslave
controllersinmultiplelocations.TobuildaMasterSlavesystem,followingthestepsbelow.
1.REMOTEDEVICESSETUPLINKTHEIPADDRESS
Inordertomakethedevicestotalktoeachother,thefirststepistolinktheslavecontrollerstothemastercontrollerthroughtheir
IPaddresses.
TousetheMasterSlavefeature,weencourageyouNOTtouseDHCPonyourcontrollers,useastaticIPoraspecificIPaddress
ifyournetworkallows.Sothatintheeventofpoweroutage,youwillnotneedtoresetIPaddresses.TousestaticIPonyourremote
controllers,gotoConfigureNetworkConfigpage,uncheckEnableDHCPbox,entertheIPaddressassignedtothatdevice,
thenclickSAVECONFIGbutton.
Iftheslavecontrollersarenotonthesamenetwork,youwillneedtoportthecontrollerstotheInternet,sothatyoucanabtaina
webaddress,thenlinkthewebaddresstothemastercontroller.
1.1TolinktheIPaddresstothemastercontroller,logintoyourmasterdevice,gotoConfiguremenu,thenselectRemote
DeviceConfigfromthedropdownmenu.
1.2OntheRemoteDevicepage,enteryourremotedevicesinformation,includingDeviceName,IPAddress,LoginUser
NameandPassword.
ClickSaveConfigbuttonafterfinish.
Repeatthestepsabovetolinkmoreremotecontrollerswiththemaster.RememberthelocationIDforeachremotedevice(location
IDfrom18underNO.column)TheRemoteDevicespagewilllooklikethis:
2.LINKTHERELAYUSETHEMASTERCONTROLLERRELAYTOTRIGGERTHESLAVECONTROLLERRELAY
Logintothemastercontrollerwebpage,gotoServiceRelays,selectRelay1,clicktheEditicon,youwillbeattheSetRelay
page.
Name:Givethisrelayaname
RelayType:Ifyouwanttherelaysatthemasterandtheslavecontrollertoturnonatthesametime,selectNormaland
Remote.Ifyouarenotusingtherelayatthemaster,butonlytocontroltheslaverelaysthenjustselectRemote.Ifyou
usethemasterrelayonly,selectNormal.
PulseWidth:Ifyouuseapushswitchtotriggertherelays,onceyoupushtheswitch,therelayshouldbeonuntilrelease
thebutton.Butjustincase,wewouldsuggestgivingtherelaysamaximumdurationsothatitwon’tbeonforever.For
example,ifyouwanttorelaytobeonfor10second,put10here,thenselectSecfromthenextbox.
PulseWidthMultiplier:selectSecifyouwanttherelaystobeonfor10secondasthesampleabove.
LocationID:EntertheremotedevicesID(from18)whichwesetonRemoteDeviceSetuppage;thefirstcolumnNo.is
thedeviceID.
RelayatLocation:From18,dependonwhichrelayyouwanttocontrolontheslavecontroller.
ClicktheSavebutton,theslaverelayhasbeenlinkedtothemasterrelay.
Ifyouhavemultislavecontrollers,useonerelayforeachslavecontrollerandrepeatthestepsabovetotriggertheremoterelay.
3.USEDIGITALINPUTTOCONTROLRELAY(S)
Youcanuseadigitalsensororapushswitchconnectingtoonethedigitalinputstotriggertherelaysonthemaster,slave,ormaster
andslave.Whenwiringthepushswitchtothedigitalinput,pleaseopentheenclosureofyourcontroller,makesurethedigitalinput
switchisatPUposition.
Logintothemastercontrollerwebpagetosetup.Whenpressthepushbutton,therelaywillbeturnedonuntilreleased.
Setdigitalinputtotriggerarelay
Tosetthepushswitchtotriggertherelay.GotoServices–In/Outpage,clickInput1(IN1)editiconifyouconnecttheswitch
toinput1,youwillbeatSetDigitalInputpage.
Name:Youcanseta15characternameforthisinput.Thisnamegoesinthebaratthetopofthedisplay.
USE:Setsthisinputtoactive.Whenthisboxischecked,itwillturntheinputnumberindicatortogreen.
Type:SelectState,thisisforknowingifaninputisonoroff.
Display:Thisselectionletsyouchangethedisplaytypeused.
RelayL/T:Enter1L,whichmeansthisinputislinkedtorelay1ifyouconnectthebelltorelay1.
ClickSAVEbutton.
4.SETUPDIGITALINPUTTRIGGER
Tosetthepushswitchtotriggertherelays.GotoServices–In/Outpage,clickInput1(IN1)editiconifyouconnecttheswitch
toinput1,youwillbeatSetDigitalInputpage.
Name:Youcanseta15characternameforthisinput.Thisnamegoesinthebaratthetopofthedisplay.
USE:Setsthisinputtoactive.Whenthisboxischecked,itwillturntheinputnumberindicatortogreen.
Type:SelectState,thisisforknowingifaninputisonoroff.
Display:Thisselectionletsyouchangethedisplaytypeused.
RelayL/T:Enter1L,whichmeansthisinputislinkedtorelay1.
ClickSAVEbutton.
Atthispoint,whenyoupushtheswitch,therelaysshouldbeturnedonforbothmasterandslavecontrollers.
Ifyouwanttobuildatwowaycommunicationsystem,youwillneedtolinkthemastercontrollertotheslavesandmakethesame
configuration.Pleasefollowthemastercontrollerconfigurationabovefortheslavecontroller.
1
EachLinortekwebrelaycontrollerincludesaremotefunctionthatcandeliverasignalfromamastercontrollertoremoteslave
controllersinmultiplelocations.TobuildaMasterSlavesystem,followingthestepsbelow.
1.REMOTEDEVICESSETUPLINKTHEIPADDRESS
Inordertomakethedevicestotalktoeachother,thefirststepistolinktheslavecontrollerstothemastercontrollerthroughtheir
IPaddresses.
TousetheMasterSlavefeature,weencourageyouNOTtouseDHCPonyourcontrollers,useastaticIPoraspecificIPaddress
ifyournetworkallows.Sothatintheeventofpoweroutage,youwillnotneedtoresetIPaddresses.TousestaticIPonyourremote
controllers,gotoConfigureNetworkConfigpage,uncheckEnableDHCPbox,entertheIPaddressassignedtothatdevice,
thenclickSAVECONFIGbutton.
Iftheslavecontrollersarenotonthesamenetwork,youwillneedtoportthecontrollerstotheInternet,sothatyoucanabtaina
webaddress,thenlinkthewebaddresstothemastercontroller.
1.1TolinktheIPaddresstothemastercontroller,logintoyourmasterdevice,gotoConfiguremenu,thenselectRemote
DeviceConfigfromthedropdownmenu.
1.2OntheRemoteDevicepage,enteryourremotedevicesinformation,includingDeviceName,IPAddress,LoginUser
NameandPassword.
ClickSaveConfigbuttonafterfinish.
Repeatthestepsabovetolinkmoreremotecontrollerswiththemaster.RememberthelocationIDforeachremotedevice(location
IDfrom18underNO.column)TheRemoteDevicespagewilllooklikethis:
2.LINKTHERELAYUSETHEMASTERCONTROLLERRELAYTOTRIGGERTHESLAVECONTROLLERRELAY
Logintothemastercontrollerwebpage,gotoServiceRelays,selectRelay1,clicktheEditicon,youwillbeattheSetRelay
page.
Name:Givethisrelayaname
RelayType:Ifyouwanttherelaysatthemasterandtheslavecontrollertoturnonatthesametime,selectNormaland
Remote.Ifyouarenotusingtherelayatthemaster,butonlytocontroltheslaverelaysthenjustselectRemote.Ifyou
usethemasterrelayonly,selectNormal.
PulseWidth:Ifyouuseapushswitchtotriggertherelays,onceyoupushtheswitch,therelayshouldbeonuntilrelease
thebutton.Butjustincase,wewouldsuggestgivingtherelaysamaximumdurationsothatitwon’tbeonforever.For
example,ifyouwanttorelaytobeonfor10second,put10here,thenselectSecfromthenextbox.
PulseWidthMultiplier:selectSecifyouwanttherelaystobeonfor10secondasthesampleabove.
LocationID:EntertheremotedevicesID(from18)whichwesetonRemoteDeviceSetuppage;thefirstcolumnNo.is
thedeviceID.
RelayatLocation:From18,dependonwhichrelayyouwanttocontrolontheslavecontroller.
ClicktheSavebutton,theslaverelayhasbeenlinkedtothemasterrelay.
Ifyouhavemultislavecontrollers,useonerelayforeachslavecontrollerandrepeatthestepsabovetotriggertheremoterelay.
3.USEDIGITALINPUTTOCONTROLRELAY(S)
Youcanuseadigitalsensororapushswitchconnectingtoonethedigitalinputstotriggertherelaysonthemaster,slave,ormaster
andslave.Whenwiringthepushswitchtothedigitalinput,pleaseopentheenclosureofyourcontroller,makesurethedigitalinput
switchisatPUposition.
Logintothemastercontrollerwebpagetosetup.Whenpressthepushbutton,therelaywillbeturnedonuntilreleased.
Setdigitalinputtotriggerarelay
Tosetthepushswitchtotriggertherelay.GotoServices–In/Outpage,clickInput1(IN1)editiconifyouconnecttheswitch
toinput1,youwillbeatSetDigitalInputpage.
Name:Youcanseta15characternameforthisinput.Thisnamegoesinthebaratthetopofthedisplay.
USE:Setsthisinputtoactive.Whenthisboxischecked,itwillturntheinputnumberindicatortogreen.
Type:SelectState,thisisforknowingifaninputisonoroff.
Display:Thisselectionletsyouchangethedisplaytypeused.
RelayL/T:Enter1L,whichmeansthisinputislinkedtorelay1ifyouconnectthebelltorelay1.
ClickSAVEbutton.
4.SETUPDIGITALINPUTTRIGGER
Tosetthepushswitchtotriggertherelays.GotoServices–In/Outpage,clickInput1(IN1)editiconifyouconnecttheswitch
toinput1,youwillbeatSetDigitalInputpage.
Name:Youcanseta15characternameforthisinput.Thisnamegoesinthebaratthetopofthedisplay.
USE:Setsthisinputtoactive.Whenthisboxischecked,itwillturntheinputnumberindicatortogreen.
Type:SelectState,thisisforknowingifaninputisonoroff.
Display:Thisselectionletsyouchangethedisplaytypeused.
RelayL/T:Enter1L,whichmeansthisinputislinkedtorelay1.
ClickSAVEbutton.
Atthispoint,whenyoupushtheswitch,therelaysshouldbeturnedonforbothmasterandslavecontrollers.
Ifyouwanttobuildatwowaycommunicationsystem,youwillneedtolinkthemastercontrollertotheslavesandmakethesame
configuration.Pleasefollowthemastercontrollerconfigurationabovefortheslavecontroller.
2
LinorTechnology,Inc.Informationsubjecttochangewithoutnotice.
  • Page 1 1
  • Page 2 2

Linortek Master-Slave User guide

Master-Slave
Brand
Linortek
Model
Master-Slave
Type
User guide

Linortek Master-Slave is a versatile device that allows you to create a remote control system for your electrical appliances. With the Master-Slave setup, you can control multiple slave devices from a single master controller over the internet. This feature is useful for automating and remotely managing devices in different locations, such as turning on lights, activating security systems, or controlling irrigation systems.

Here are some key capabilities of the Linortek Master-Slave:

  • Remote control: Link multiple slave devices to a master controller using their IP addresses and control them remotely from anywhere with an internet connection.
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents