Sensor QSx-G2 HAZ User guide

Brand
Sensor
Model
QSx-G2 HAZ
Category
Signal cables
Type
User guide

Below you will find brief information for Oil Quality Sensor OQSx-G2 HAZ. This quick start guide provides instructions on how to configure, install, and connect the OQSx-G2 HAZ oil quality sensor. It outlines the necessary steps, including driver installation, software setup, selecting communication protocols, and proper installation orientation. The guide also includes troubleshooting tips and highlights the sensor's digital outputs and operating temperature range.

Below you will find brief information for Oil Quality Sensor OQSx-G2 HAZ. This quick start guide provides instructions on how to configure, install, and connect the OQSx-G2 HAZ oil quality sensor. It outlines the necessary steps, including driver installation, software setup, selecting communication protocols, and proper installation orientation. The guide also includes troubleshooting tips and highlights the sensor's digital outputs and operating temperature range.

Oil Quality Ex-Sensor (OQSx-G2 HAZ)
WHAT’S IN THE BOX?
1. CONFIGURE
2. INSTALL
3. CONNECT
4. ACTIVATION STEPS TROUBLESHOOTING
1. OEM Port 2. Tan Delta Manifold 3. Oil Filter
Location options
Oil Filter
Analogue 4-20 mA
Oil
TDN
Temp
(˚C)
4
20
1200 5 mA
17 mA
0
-30
+130
Check installation
Power on
Wait for 1 minute
Check output
Comparing electrical output
with oil condition and temp.
Sensor may not function if installed incorrectly NOTE: Refer to Master User Guide for additional safety information regarding installation
Ex-Sensor
Configuration Cable
(Cable X)
OQSx-G2 HAZ
Sensor Cable
Cable X
Product
USB
Cable X
Product USB
• Configuration &
Data software (CADs )
• Manuals
• Quick Start Guide
Orientation Immersion
45˚ 45˚
270˚
RS485A
-
+
-
O
Y
G
R
BR
BL
+
Oil condition
Oil temperature
RS485B Digital RS485
Modbus CANbus
(see manual)
10-28.8V DC
ATEX Barrier
4-20 mA
4-20 mA
OQSx-G2 HAZ
SENSOR
I
OQSx-G2 HAZ
QUICK START GUIDE
1. Check configuration.
2. Refer to Installation Drawing 401-0229 on USB
3. Refer to Master User Guide:
www.tandeltasystems.com/support
4. Contact: [email protected]
www.tandeltasystems.com
suppor[email protected]
Copyright © Tan Delta Systems Ltd.
Quick Start
Guide
1. Allow Configuration Cable to install and update drivers.
2. Install CADS by scanning the QR code below or go to:
www.tandeltasystems.com/support/
3. Select the correct comms protocol and oil type.
SCAN ME
SENSOR
I
OQSx-G2 HAZ
QUICK START GUIDE
www.tandeltasystems.com
suppor[email protected]
Copyright © Tan Delta Systems Ltd.
You can find further information in the Master User Guide on the support page of our
website. If you have any further questions, please contact our support team by email:
[email protected] who will answer no later than the next working day.
Alternatively, refer to Master User Guide
available at: www.tandeltasystems.com/support
SCAN ME
Page 2 of 2
SUPPORT – FAQ
If you have any issues, please read the tips below before contacting us for further support.
1. Where are the Cable X drivers?
The drivers for Cable X should install automatically. If needed, they are also available on the USB stick supplied with the product.
2. Does the sensor require cleaning?
No, cleaning is required once the sensor is installed. However, when using the sensor for testing offline samples (i.e. MOT Kit), then cleaning
between samples is essential.
3. I cannot see my oil in the database, so I have used an oil which I believe is close, but the sensor isn’t working?
The sensor will exhibit a different response for every oil. For best results, it is advised to obtain an Oil Profile which Tan Delta will add to
our Oil Database. Please complete and submit an Oil Profile Request Form online at www.tandeltasystems.com/oil-availability-checker/
4. Where can I obtain the EU and UK Declaration of Conformity?
The Declaration of Conformity (EU and UK) for the product are available on the USB supplied and can also be downloaded online at
www.tandeltasystems.com/products/oqsxg2hazsensor.
5. I need help sourcing a suitable ATEX Barrier for my application?
Contact [email protected] and we will be happy to help.
  • Page 1 1
  • Page 2 2

Sensor QSx-G2 HAZ User guide

Brand
Sensor
Model
QSx-G2 HAZ
Category
Signal cables
Type
User guide

Below you will find brief information for Oil Quality Sensor OQSx-G2 HAZ. This quick start guide provides instructions on how to configure, install, and connect the OQSx-G2 HAZ oil quality sensor. It outlines the necessary steps, including driver installation, software setup, selecting communication protocols, and proper installation orientation. The guide also includes troubleshooting tips and highlights the sensor's digital outputs and operating temperature range.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents