ABB REL 551 2.3 Series Installation And Comissioning Manual

,QVWDOODWLRQDQGFRPPLVVLRQLQJPDQXDO

REL 551*2.3

Line differential protection terminal

$ERXWWKLVPDQXDO

Document No: 1MRK 506 078-UEN

Issued: March 2003

Revision: B

&23<5,*+7

:(5(6(59($//5,*+76727+,6'2&80(17(9(1,17+((9(177+$7$3$7(17,6

,668('$1'$',))(5(17&200(5&,$/35235,(7$5<5,*+7,65(*,67(5(',03523(5

86(,13$57,&8/$55(352'8&7,21$1'',66(0,1$7,21727+,5'3$57,(6,6127

3(50,77('

7+,6'2&80(17+$6%((1&$5()8//<&+(&.(',)7+(86(51(9(57+(/(66'(7(&76

$1<(55256+(,6$6.('72127,)<86$66221$63266,%/(

7+('$7$&217$,1(',17+,60$18$/,6,17(1'('62/(/<)257+(&21&(3725

352'8&7'(6&5,37,21$1',612772%('((0('72%($67$7(0(172)*8$5$1

7(('3523(57,(6,17+(,17(5(6762)285&86720(56:(&2167$17/<6((.72

(1685(7+$7285352'8&76$5('(9(/23('727+(/$7(677(&+12/2*,&$/67$1

'$5'6$6$5(68/7,7,63266,%/(7+$77+(5(0$<%(620(',))(5(1&(6%(7:((1

7+(+:6:352'8&7$1'7+,6,1)250$7,21352'8&7

0DQXIDFWXUHU

ABB Automation Technology Products AB

Substation Automation

SE-721 59 Västerås

Sweden

Telephone: +46 (0) 21 34 20 00

Facsimile: +46 (0) 21 14 69 18

Internet: www.abb.com/substationautomation

&RQWHQWV

3DJH&KDSWHU

&KDSWHU ,QWURGXFWLRQ  

Introduction to the installation and commissioning manual ................. 2

About the complete set of manuals for a terminal .......................... 2

About the installation and commissioning manual.......................... 3

Intended audience.......................................................................... 3

Related documents......................................................................... 4

Revision notes................................................................................ 4

&KDSWHU 6DIHW\LQIRUPDWLRQ 

Warning signs...................................................................................... 6

Caution signs....................................................................................... 8

Note signs............................................................................................ 9

&KDSWHU 2YHUYLHZ  

Commissioning and installation overview.......................................... 12

&KDSWHU 8QSDFNLQJDQGFKHFNLQJWKHWHUPLQDO  

Receiving, unpacking and checking .................................................. 14

&KDSWHU ,QVWDOOLQJWKHWHUPLQDO  

Overview............................................................................................ 16

Mounting the terminal ........................................................................ 17

Mounting in a 19-inch rack ........................................................... 18

Mounting in a 19-inch rack with an additional box type RHGS..... 19

Mounting in a flush or semi-flush installation................................ 21

Mounting on a wall ....................................................................... 24

Making the electrical connections...................................................... 27

Connecting the CT circuits............................................................ 27

Connecting the auxiliary power, VT and signal connectors.......... 27

Connecting to protective ground................................................... 29

Making the screen connection...................................................... 29

Installing the optical fibres ................................................................. 30

Installing the communication cables.................................................. 31

&RQWHQWV

&KDSWHU &KHFNLQJWKHH[WHUQDOFLUFXLWU\  

Overview............................................................................................ 34

Checking the CT and VT circuits ....................................................... 35

Checking the power supply................................................................ 36

Checking the binary I/O circuits......................................................... 37

Binary input circuits....................................................................... 37

Binary output circuits .................................................................... 37

&KDSWHU (QHUJLVLQJWKHWHUPLQDO 

Overview............................................................................................ 40

Energising the terminal...................................................................... 41

Checking the self supervision signals................................................ 43

Reconfiguring the terminal............................................................ 43

Setting the terminal time............................................................... 43

Checking the self supervision function ......................................... 44

Self supervision HMI data............................................................. 44

&KDSWHU &RQILJXULQJWKHGLJLWDOFRPPXQLFDWLRQPRGXOHV 

Configuring the fibre optical modem.................................................. 48

Configuring the short range fibre optical modem............................... 49

Configuring the short range galvanic modem.................................... 53

Configure the interface modules for V.36, X.21 and RS530.............. 55

Configuring the interface modules for G.703 co-directional............... 57

&KDSWHU 6HWWLQJDQGFRQILJXULQJWKHWHUPLQDO 

Overview............................................................................................ 60

Entering settings through the local HMI............................................. 61

Downloading settings and configuration from a PC........................... 62

Establishing front port communication.......................................... 62

Establishing rear port communication........................................... 62

Downloading the configuration and setting files ........................... 64

&KDSWHU (VWDEOLVKLQJFRQQHFWLRQDQGYHULI\LQJWKH63$,(&

FRPPXQLFDWLRQ 

Entering settings................................................................................ 66

Entering SPA settings................................................................... 66

Entering IEC settings.................................................................... 66

Verifying the communication.............................................................. 68

Verifying SPA communication ...................................................... 68

Verifying IEC communication........................................................ 68

&RQWHQWV

&KDSWHU 9HULI\LQJVHWWLQJVE\VHFRQGDU\LQMHFWLRQ  

Overview............................................................................................ 70

Preparing for test............................................................................... 72

Overview....................................................................................... 72

Preparing the connection to the test equipment........................... 72

Setting the terminal in test mode.................................................. 73

Connecting test equipment to the terminal................................... 73

Verifying the connection and the analog inputs............................ 74

Releasing the function(s) to be tested.......................................... 75

Checking the disturbance report settings ..................................... 76

Automatic reclosing function (AR) ..................................................... 77

Preparing...................................................................................... 78

Checking the AR functionality....................................................... 79

Checking the reclosing condition.................................................. 80

Testing the multi-breaker arrangement......................................... 81

Completing the test....................................................................... 81

Breaker failure protection (BFP) ........................................................ 82

Verifying the settings .................................................................... 82

Verifying the retrip setting............................................................. 82

Completing the test....................................................................... 83

Broken conductor check (BRC) ......................................................... 84

Measuring the operate and time limit of set values ...................... 84

Communication channel test logic (CCHT)........................................ 86

Testing the logic ........................................................................... 86

Current circuit supervision (CTSU).................................................... 87

Definite and inverse time-delayed residual

overcurrent protection (TEF) ............................................................. 88

Checking the operate values of the

current measuring elements ................................................. 88

Disturbance recorder (DRP) .............................................................. 92

Event counter (CN)............................................................................ 93

Event function (EV)............................................................................ 94

Event recorder ................................................................................... 95

Instantaneous overcurrent protection (IOC) ...................................... 96

Measuring the operate limit of set values..................................... 96

Completing the test....................................................................... 97

Line differential protection (DIFL) ...................................................... 98

Testing the line differential protection......................................... 100

Testing the charging current compensation................................ 102

Completing the test..................................................................... 104

Monitoring of AC analogue measurements ..................................... 105

Verifying the settings .................................................................. 105

Completing the test..................................................................... 106

Monitoring of DC analogue measurements ..................................... 107

Verifying the settings .................................................................. 107

Completing the test..................................................................... 108

Multiple command (CM)................................................................... 109

Overload supervision (OVLD).......................................................... 110

Measuring the operate and time limit of set values .................... 110

Pole discordance protection (PD).................................................... 112

&RQWHQWV

Pulse counter logic (PC).................................................................. 113

Setting lockout (HMI) ....................................................................... 114

Verifying the settings .................................................................. 114

Completing the test..................................................................... 114

Setting group selector (GRP)........................................................... 115

Verifying the settings .................................................................. 115

Single command (CD)...................................................................... 116

Thermal overload protection (THOL)............................................... 117

Measuring the operate and time limit of set values .................... 117

Time delayed overcurrent protection (TOC) .................................... 119

Measuring the operate limit of set values ................................... 119

Completing the test..................................................................... 120

Trip logic (TR).................................................................................. 121

3ph operating mode.................................................................... 121

1ph/3ph operating mode............................................................. 121

1ph/2ph/3ph operating mode...................................................... 122

Completing the test..................................................................... 123

Two step time delayed phase overcurrent protection (TOC2)......... 124

Measuring the operate and time limit for set values ................... 124

Completing the test..................................................................... 125

&KDSWHU 9HULI\LQJWKHLQWHUQDOFRQILJXUDWLRQ 

Overview.......................................................................................... 128

Testing the interaction of the distance protection ............................ 129

&KDSWHU 7HVWLQJWKHSURWHFWLRQV\VWHP  

Overview.......................................................................................... 132

Testing the interaction of the distance protection ............................ 133

1

About this chapter &KDSWHU

,QWURGXFWLRQ

&KDSWHU ,QWURGXFWLRQ

$ERXWWKLVFKDSWHU

This chapter introduces the user to the manual.

2

Introduction to the installation and

commissioning manual

&KDSWHU

,QWURGXFWLRQ

 ,QWURGXFWLRQWRWKHLQVWDOODWLRQDQGFRPPLVVLRQLQJ

PDQXDO

 $ERXWWKHFRPSOHWHVHWRIPDQXDOVIRUDWHUPLQDO

The complete package of manuals to a terminal is named users manual (UM). The 8V

HUVPDQXDO consists of four different manuals:

7KH$SSOLFDWLRQ0DQXDO$0 contains descriptions, such as application and func-

tionality descriptions as well as setting calculation examples sorted per function. The

application manual should be used when designing and engineering the protection ter-

minal to find out when and for what a typical protection function could be used. The

manual should also be used when calculating settings and creating configurations.

7KH7HFKQLFDO5HIHUHQFH0DQXDO750 contains technical descriptions, such as

function blocks, logic diagrams, input and output signals, setting parameter tables and

technical data sorted per function. The technical reference manual should be used as a

technical reference during the engineering phase, installation and commissioning phase

and during the normal service phase.

7KH2SHUDWRUV0DQXDO20 contains instructions on how to operate the protection

terminal during normal service (after commissioning and before periodic maintenance

tests). The operator´s manual could be used to find out how to handle disturbances or

how to view calculated and measured network data in order to determine the reason of

a fault.

7KH,QVWDOODWLRQDQG&RPPLVVLRQLQJ0DQXDO,&0 contains instructions on how to

install and commission the protection terminal. The manual can also be used as a refer-

ence if a periodic test is performed. The manual covers procedures for mechanical and

electrical installation, energising and checking of external circuitry, setting and config-

uration as well as verifying settings and performing a directionality test. The chapters

and sections are organized in the chronological order (indicated by chapter/section

numbers) the protection terminal should be installed and commissioned.

Application

manual

Technical

reference

manual

Installation and

commissioning

manual

Operator´s

manual

en01000044.vsd

3

Introduction to the installation and

commissioning manual

&KDSWHU

,QWURGXFWLRQ

 $ERXWWKHLQVWDOODWLRQDQGFRPPLVVLRQLQJPDQXDO

The installation and commissioning manual contains the following chapters:

• The chapter ³6DIHW\LQIRUPDWLRQ´ presents warning and note signs, which the user

should pay attention to.

• The chapter ³2YHUYLHZ´ gives an overview over the major tasks when installing

and commissioning the terminal.

• The chapter ³8QSDFNLQJDQGFKHFNLQJWKHWHUPLQDO´ contains instructions on how

to receive the terminal.

• The chapter ³,QVWDOOLQJWKHWHUPLQDO´ contains instructions on how to install the ter-

minal.

• The chapter ³&KHFNLQJWKHH[WHUQDOFLUFXLWU\´ contains instructions on how to

check that the terminal is properly connected to the protection system.

• The chapter ³(QHUJLVLQJWKHWHUPLQDO´ contains instructions on how to start-up the

terminal.

• The chapter ³&RQILJXULQJWKHGLJLWDOFRPPXQLFDWLRQPRGXOHV´ contains instruc-

tions on how to configure the communication modules such as modems, optical

converters etc if included in the terminal.

• The chapter ³6HWWLQJDQGFRQILJXULQJWKHWHUPLQDO´ contains instructions on how to

download settings and configuration to the terminal.

• The chapter ³(VWDEOLVKLQJFRQQHFWLRQDQGYHULI\LQJWKH63$,(&FRPPXQLFDWLRQ´

contains instructions on how to enter SPA/IEC settings and verifying the SPA/IEC

communication.

• The chapter ³9HULI\LQJVHWWLQJVE\VHFRQGDU\LQMHFWLRQ´ contains instructions on

how to verify that each included function operates correctly according to the set val-

ues.

• The chapter ³9HULI\LQJWKHLQWHUQDOFRQILJXUDWLRQ´ contains instructions on how

verify that the terminal is properly configured.

• The chapter ³7HVWLQJWKHSURWHFWLRQV\VWHP´ contains instructions on how to test

that the terminal is in contact with the primary system.

• The chapter ³&KHFNLQJWKHGLUHFWLRQDOLW\´ contains instructions on how to test di-

rectional dependent functions, if included in the terminal.

 ,QWHQGHGDXGLHQFH

 *HQHUDO

The installation and commissioning manual is addressing the installation, commission-

ing and maintenance personnel responsible for taking the protection into normal service

and out of service.

4

Introduction to the installation and

commissioning manual

&KDSWHU

,QWURGXFWLRQ

 5HTXLUHPHQWV

The installation personnel must have a basic knowledge in handling electronic equip-

ment. The commissioning and maintenance personnel must be well experienced in us-

ing protection equipment, test equipment, protection functions and the configured

functional logics in the protection.

 5HODWHGGRFXPHQWV

 5HYLVLRQQRWHV

'RFXPHQWVUHODWHGWR5(/ ,GHQWLW\QXPEHU

Operator’s manual 1MRK 506 076-UEN

Installation and commissioning manual 1MRK 506 078-UEN

Technical reference manual 1MRK 506 077-UEN

Application manual 1MRK 506 112-UEN

Technical overview brochure 1MRK 506 075-BEN

5HYLVLRQ 'HVFULSWLRQ

A Update of chapters 8 and 11

5

About this chapter &KDSWHU

6DIHW\LQIRUPDWLRQ

&KDSWHU 6DIHW\LQIRUPDWLRQ

$ERXWWKLVFKDSWHU

This chapter contains safety information. Warning signs are presented which attend the

user to be careful during certain operations in order to avoid human injuries or damage

to equipment

6

Warning signs &KDSWHU

6DIHW\LQIRUPDWLRQ

 :DUQLQJVLJQV

:DUQLQJ

6WULFWO\IROORZWKHFRPSDQ\DQGFRXQWU\VDIHW\UHJXODWLRQV:RUNLQJLQDKLJKYROWDJH

HQYLURQPHQWUHTXLUHVVHULRXVDSSURDFKWRDYRLGKXPDQLQMXULHVDQGGDPDJHWRHTXLS

PHQW

:DUQLQJ

'RQRWWRXFKFLUFXLWU\GXULQJRSHUDWLRQ3RWHQWLDOO\OHWKDOYROWDJHVDQGFXUUHQWVDUH

SUHVHQW

:DUQLQJ

$OZD\VDYRLGWRWRXFKWKHFLUFXLWU\ZKHQWKHFRYHULVUHPRYHG7KHSURGXFWFRQWDLQV

HOHFWURQLFFLUFXLWULHVZKLFKFDQEHGDPDJHGLIH[SRVHGWRVWDWLFHOHFWULFLW\(6'7KH

HOHFWURQLFFLUFXLWULHVDOVRFRQWDLQKLJKYROWDJHZKLFKLVOHWKDOWRKXPDQV

:DUQLQJ

$OZD\VXVHVXLWDEOHLVRODWHGWHVWSLQVZKHQPHDVXULQJVLJQDOVLQRSHQFLUFXLWU\3RWHQ

WLDOO\OHWKDOYROWDJHVDQGFXUUHQWVDUHSUHVHQW

3URKLELWLRQ

1HYHUFRQQHFWRUGLVFRQQHFWDZLUHDQGRUDFRQQHFWRUWRRUIURPDWHUPLQDOGXULQJ

QRUPDORSHUDWLRQ+D]DUGRXVYROWDJHVDQGFXUUHQWVDUHSUHVHQWWKDWPD\EHOHWKDO2S

HUDWLRQPD\EHGLVUXSWHGDQGWHUPLQDODQGPHDVXULQJFLUFXLWU\PD\EHGDPDJHG

:DUQLQJ

$OZD\VFRQQHFWWKHWHUPLQDOWRSURWHFWLYHHDUWKUHJDUGOHVVRIWKHRSHUDWLQJFRQGLWLRQV

7KLVDOVRDSSOLHVWRVSHFLDORFFDVLRQVVXFKDVEHQFKWHVWLQJGHPRQVWUDWLRQVDQGRII

VLWHFRQILJXUDWLRQ2SHUDWLQJWKHWHUPLQDOZLWKRXWSURSHUHDUWKLQJPD\GDPDJHERWK

WHUPLQDODQGPHDVXULQJFLUFXLWU\DQGPD\FDXVHLQMXULHVLQFDVHRIDQDFFLGHQW

7

Warning signs &KDSWHU

6DIHW\LQIRUPDWLRQ

:DUQLQJ

1HYHUGLVFRQQHFWDVHFRQGDU\FRQQHFWLRQRIFXUUHQWWUDQVIRUPHUFLUFXLWZLWKRXWVKRUW

FLUFXLWLQJWKHWUDQVIRUPHU¶VVHFRQGDU\ZLQGLQJ2SHUDWLQJDFXUUHQWWUDQVIRUPHUZLWK

WKHVHFRQGDU\ZLQGLQJRSHQZLOOFDXVHDPDVVLYHSRWHQWLDOEXLOGXSWKDWPD\GDPDJH

WKHWUDQVIRUPHUDQGPD\FDXVHLQMXULHVWRKXPDQV

:DUQLQJ

1HYHUUHPRYHDQ\VFUHZIURPDSRZHUHGWHUPLQDORUIURPDWHUPLQDOFRQQHFWHGWRSRZ

HUHGFLUFXLWU\3RWHQWLDOO\OHWKDOYROWDJHVDQGFXUUHQWVDUHSUHVHQW

8

Caution signs &KDSWHU

6DIHW\LQIRUPDWLRQ

 &DXWLRQVLJQV

&DXWLRQ

$OZD\VWUDQVSRUWPRGXOHVXVLQJFHUWLILHGFRQGXFWLYHEDJV$OZD\VKDQGOHPRGXOHVXV

LQJDFRQGXFWLYHZULVWVWUDSFRQQHFWHGWRSURWHFWLYHJURXQGDQGRQDVXLWDEOHDQWLVWDWLF

VXUIDFH(OHFWURVWDWLFGLVFKDUJH(6'PD\FDXVHGDPDJHWRWKHPRGXOH

&DXWLRQ

'RQRWFRQQHFWOLYHZLUHVWRWKHWHUPLQDO,QWHUQDOFLUFXLWU\PD\EHGDPDJHG

&DXWLRQ

$OZD\VXVHDFRQGXFWLYHZULVWVWUDSFRQQHFWHGWRSURWHFWLYHJURXQGZKHQUHSODFLQJ

PRGXOHV(OHFWURVWDWLFGLVFKDUJH(6'PD\GDPDJHWKHPRGXOHDQGWHUPLQDOFLUFXLW

U\

&DXWLRQ

7DNHFDUHWRDYRLGHOHFWULFDOVKRFNLIDFFHVVLQJZLULQJDQGFRQQHFWLRQWHUPLQDOVZKHQ

LQVWDOOLQJDQGFRPPLVVLRQLQJ

&DXWLRQ

&KDQJLQJWKHDFWLYHVHWWLQJJURXSZLOOLQHYLWDEO\FKDQJHWKHWHUPLQDO¶VRSHUDWLRQ%H

FDUHIXODQGFKHFNUHJXODWLRQVEHIRUHPDNLQJWKHFKDQJH

9

Note signs &KDSWHU

6DIHW\LQIRUPDWLRQ

 1RWHVLJQV

1RWH

7KHSURWHFWLRQDVVHPEO\LVGHVLJQHGIRUDPD[LPXPFRQWLQXRXVFXUUHQWRIIRXUWLPHV

UDWHGYDOXH

1RWH

$FWLYDWLQJWKHVHWWLQJORFNRXWIXQFWLRQZKLFKSUHYHQWVXQDXWKRULVHGFKDQJHVRIWKHVHW

WLQJVZLWKRXWSURSHUFRQILJXUDWLRQPD\VHULRXVO\DIIHFWWKHWHUPLQDO¶VRSHUDWLRQ

10

Note signs &KDSWHU

6DIHW\LQIRUPDWLRQ

11

About this chapter &KDSWHU

2YHUYLHZ

&KDSWHU 2YHUYLHZ

$ERXWWKLVFKDSWHU

This chapter introduces the user to the installation and commissioning tasks.

12

Commissioning and installation overview &KDSWHU

2YHUYLHZ

 &RPPLVVLRQLQJDQGLQVWDOODWLRQRYHUYLHZ

The settings for each function must be calculated before the commissioning task can

start. A configuration, made in the configuration and programming tool, must also be

available if the terminal does not have a factory configuration downloaded.

The terminal is unpacked and visually checked. It is preferably mounted in a cubicle or

on a wall. The connection to the protection system has to be checked in order to verify

that the installation was successful.

The installation and commissioning task starts with configuring the digital communica-

tion modules, if included. The terminal can then be configured and set, which means

that settings and a configuration has to be applied if the terminal does not have a factory

configuration downloaded. Then the operation of each included function according to

applied settings has to be verified by secondary injection. A complete check of the con-

figuration can then be made. A conformity test of the secondary system has also to be

done. When the primary system has been energised a directionality check should be

made.

13

About this chapter &KDSWHU

8QSDFNLQJDQGFKHFNLQJWKH

WHUPLQDO

&KDSWHU 8QSDFNLQJDQG

FKHFNLQJWKH

WHUPLQDO

$ERXWWKLVFKDSWHU

This chapter contains instructions on how to receive the terminal.

14

Receiving, unpacking and checking &KDSWHU

8QSDFNLQJDQGFKHFNLQJWKH

WHUPLQDO

 5HFHLYLQJXQSDFNLQJDQGFKHFNLQJ

3URFHGXUH

 5HPRYHWKHWUDQVSRUWFDVLQJ

 9LVXDOO\LQVSHFWWKHWHUPLQDO

 &KHFNWKDWDOOLWHPVDUHLQFOXGHGLQDFFRUGDQFHZLWKWKHGH

OLYHU\GRFXPHQWV

The user is requested to check that all software functions are in-

cluded according to the delivery documents after the terminal has

been energised.

 &KHFNIRUWUDQVSRUWGDPDJHV

In case of transport damage appropriate action must be taken

against the latest carrier and the nearest ABB office or representa-

tive should be informed. ABB should be notified immediately if

there are any discrepancies in relation to the delivery documents.

Store the terminal in the original transport casing in a dry and dust

free place, if the terminal is not to be installed or commissioned

immediately. Observe the environmental requirements stated in

the technical data.

Page is loading ...

ABB REL 551 2.3 Series Installation And Comissioning Manual

This manual is also suitable for

ABB REL 551 2.3 Series Installation And Comissioning Manual

Related papers

Other documents