Bissell 1240 Series User manual

Brand: Bissell

Model: 1240 Series

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

Thank You

USER'S GUIDE

12B1, 1240, 68C7 SERIES

Safety Instructions

Product View

4-5

Assembly

Operations

7-8

Maintenance and Care

9-12

Troubleshooting

Replacement Parts

Warranty

Product Registration

Consumer Care

Thanks for buying a BISSELL vacuum

We’re glad you purchased a BISSELL vacuum. Everything we know

about floor care went into the design and construction of this powerful,

high-tech home vacuuming system.

Your BISSELL vacuum is well made, and we back it with a limited one

year warranty. We also stand behind it with a knowledgeable, dedicated

Consumer Care Department, so, should you ever have a problem, you’ll

receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL

is a global leader in the design, manufacture, and service of high quality

homecare products like your BISSELL PowerForce Bagless vacuum.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

Chairman, President & CEO

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical

appliance, basic

precautions should be observed, including

the following:

READ ALL INSTRUCTIONS

BEFORE USING YOUR

UPRIGHT VACUUM.

Always connect to a polarized outlet

(left slot is wider than right). Unplug

from outlet when not in use and before

conducting maintenance.

WARNING: To

reduce the risk of fire,

electric shock, or injury:

■ Do not modify the polarized plug to t a

non-polarized outlet or extension cord.

■ Do not leave vacuum cleaner unattended

when it is plugged in.

■ Unplug from outlet when not in use and

before servicing.

■ Do not use outdoors or on wet surfaces.

■ Do not allow children to operate vacuum

cleaner or use as a toy.

■ Close attention is necessary when used by

or near children.

■ Do not use for any purpose other than

described in this User’s Guide.

■ Use only manufacturer’s recommended

attachments.

■ Do not use with damaged cord or plug.

■ If appliance is not working as it should, has

been dropped, damaged, left outdoors, or

dropped into water, have it repaired at an

authorized service center.

■ Do not pull or carry by cord, use cord as a

handle, close a door on cord, or pull cord

around sharp edges or corners. Do not run

appliance over cord. Keep cord away from

heated surfaces.

■ Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

■ Do not handle vacuum cleaner or plug with

wet hands.

■ Do not put any object into openings.

Do not use with any opening blocked;

keep openings free of dust, lint, hair, and

anything that may reduce air ow.

■ Keep hair, loose clothing, ngers, and all

parts of body away from openings and

moving parts.

■ Turn o all controls before plugging or

unplugging vacuum cleaner.

■ Use extra care when cleaning stairs.

■ Do not pick up ammable materials

(lighter uid, gasoline, kerosene, etc.) or

use in the presence of explosive liquids or

vapors.

■ Do not pick up toxic material (chlorine

bleach, ammonia, drain cleaner, etc.).

■ Do not use vacuum cleaner in an enclosed

space lled with vapors given o by oil

base paint, paint thinner, some moth

proong substances, ammable dust, or

other explosive or toxic vapors.

■ Do not pick up hard or sharp objects such

as glass, nails, screws, coins, etc.

■ Do not pick up anything that is burning or

smoking, such as cigarettes, matches, or

hot ashes.

■ Do not use without lters in place.

■ Use only on dry, indoor surfaces.

■ Keep appliance on a level surface.

■ Do not carry the vacuum cleaner while it

is running.

■ Unplug before connecting TurboBrush® Tool.

SAVE THESE

INSTRUCTIONS

FOR FUTURE USE

THIS APPLIANCE

HAS A POLARIZED

PLUG.

To reduce the risk of electric shock, this

appliance has a polarized plug (one blade

is wider than the other). This plug will

fit in a polarized outlet only one way. If

the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit,

contact a qualified electrician to install a

proper outlet. Do not change the plug in

any way.

This model is for household use only.

Product View

68C7 Model Shown

Handle

Powerfoot

Furniture

Protection

Guard

Height

Adjustment

Knob

Post Motor HEPA

Media Filter*

(select 68C7 Models)

Lock ’n Seal™ Lever

Inner and Outer

Circular Filters

Upper Tank

Quick Release™

Cord Wrap

Power Cord

Primary Separator

TurboBrush® Tool

(68C7 Models)

Easy Empty™

Dirt Container

Lower

Filter Cup

* The filter media, not the vacuum as a whole, complies with the

IEST-RP-CC001.5 or the EN-1822-1:2009 HEPA standard.

Product View

Carrying

Handle

Power Switch

Crevice Tool

Handle

Release

Pedal

Stretch Hose

68C7 Model Shown

Extension Wand

Combination

Dusting Brush/

Upholstery Tool

Hose Wand

Hose

Wand Base

Foot Hose

Hose Clip

Cord Clip

Assembly

Attach handle to vacuum

1. Locate handle and remove screw packet

taped to the base of the handle.

2. Stand the vacuum upright and place the

base of the handle firmly into the grooves

at the top of the vacuum body.

3. Insert the two (2) screws into the existing

holes on each side and tighten securely.

Attach vacuum hose and tools

1. Line up tabs on the base of the Twist

‘n Snap™ hose with the corresponding

notches on the hose collar. Turn the hose

to the right to lock into place.

2. Grasp the Quick Reach handle and slide

the end of the hose into the hose wand

base. Snap the hose into the upper hose

clip on handle.

3. Slide the extension wand and crevice tool

together into storage clip.

4. Snap the combination tool into the

storage clip.

Select models only:

5. The TurboBrush® Tool bracket slides into

the front of the handle. Attach the bracket

by aligning the pegs with the holes on

the handle and pulling down until it locks

into place.

6. Place the TurboBrush® Tool in the bracket

by aligning the bottom of bracket with

the opening of the brush roll and snap

the TurboBrush® Tool into place.

5 6

WARNING:

Plastic packaging can be

dangerous. To avoid danger

of suffocation, keep away

from babies and children.

Tip:

Hold onto the plastic hose

collar while installing. It may

be easier to lock the hose into

place when the hose handle is

not yet inserted into the base

of the unit.

Operations

Power Switch

The red power switch is located on the

bottom left of the back side of the unit.

Press gently with foot to turn power ON

and OFF.

Power Cord

When you are nished vacuuming, return

to upright position and store power cord.

1. Turn vacuum OFF.

2. Unplug power cord by grasping the

polarized plug (NOT the cord) and

disconnect from outlet.

3. Loop power cord around cord wraps on

side of vacuum and clip molded plug to

power cord to secure.

Handle Positions

The handle release pedal is located just

under the red power switch on the bottom

left of the back of the vacuum. Press the

black handle release pedal with foot to

place vacuum into one of three cleaning

positions:

1. Upright: for storage, transporting, and

above floor cleaning with tools.

• Transport in upright position by tilting

vacuum on rear wheels and push

forward or use carrying handle on

back of handle base.

2. Normal Cleaning: Press handle

release pedal once for most

household floor cleaning.

3. Low Cleaning: From normal

cleaning position, press handle

release pedal once for cleaning

under low furniture.

Operations

Height Adjustments (select models

Turn knob on Powerfoot to adjust to

one of 5 Height Adjustments. If knob

is dicult to turn, tilt the cleaner back

slightly to take the weight o the foot

while turning.

Lowest Setting: For low pile carpet and

barefloors.

Medium Setting: For medium pile carpet.

Highest Setting: For high pile and most shag

carpet. Adjust to high setting if difficult to push.

Tools

Attach desired tool to hose cleaning

above oor surfaces.

1. Remove Hose: With vacuum in upright

position, grasp the Quick Reach Handle

and lift hose wand to separate from suction

intake opening.

2. Attach tools by firmly pushing onto

vacuum hose or extension wand.

A. Combination dusting brush/

upholstery tool: Rotate for desired

use. Use brush side to dust, blinds,

books, lamps, shelves, and baseboards.

Use upholstery side to for furniture,

drapes and, fabrics.

B. Crevice Tool: Use in tight narrow

spaces.

C. Extension Wand: Use with desired

attachment for longer reach.

D. TurboBrush® Tool (Select Models):

Use rotating brush action for small flat

areas such as stairs, and cushions.

Press down gently and pull towards you

in a raking motion. Too much pressure

will cause the brush to stop rotating.

Maintenance and Care

To maximize performance and extend life

of your vacuum it is very important to

perform the following maintenance steps.

Empty Easy Empty™

Dirt Container

Empty when dirt reaches the “Full” line on

the container

1. Turn power OFF. Unplug power cord from

electrical outlet.

2. Slide Lock ‘n Seal lever to “Unlock” position.

3. Grasp dirt cup portion handle and pull straight

out to remove from vacuum and empty.

4. Place dirt container back in the vacuum and

slide lever to lock position.

NOTE: The dirt container may be

washed in warm water with mild

detergent. Make sure it is completely

dry before replacing.

Cleaning Inner & Outer

Circular Filter

To maintain suction and cleaning

performance, check and clean lters regularly

1. Turn power OFF. Unplug vacuum cord from

electrical outlet

2. Remove dirt container. Grasp the filter

located at the bottom of the dirt container,

lift and pull straight out. DO NOT PULL

CIRCULAR FOAM FILTER OUT OF THE FILTER

CUP WHILE IT IS STILL IN THE VACUUM.

3. Grasp the plastic tab on the top of the circular

foam filters. Twist to unlock and pull out.

4. Separate the outer foam filter and inner pleated

circular filter. Wash each individually by hand

in warm water. Mild detergent may be used if

desired. Rinse well, let filters completely air dry

before replacing in filter cup.

5. Wash filter cup in warm water with mild

detergent. Completely air dry before

reassembling with filters. DO NOT PUT IN

DISHWASHER.

6. The upper tank and louvers can be wiped

clean with a damp cloth. Reach underneath

the upper tank and turn the rim of the

louvers to the left to unlock. Pull straight

down and remove. Make sure all parts are

completely dry before replacing.

7. To replace louvers, position top of louvers

inside clear center cavity and turn toward

the right to lock tabs into place.

2 3

Maintenance and Care

Cleaning the Pre-Motor Filter

The pre-motor lter protects the motor

from debris.

1. Turn power OFF. Unplug vacuum cord

from electrical outlet.

2. The pre motor filter is located underneath

the filter cup in the center of the round

part of the Lock ‘n Seal lever.

3. Remove the small round filter and any

debris on top of it. Rinse under warm

water; air dry completely before replacing.

Replacing the HEPA Media filter*

(select 68C7 model series only)

The HEPA Media lter* assists in the

ltration process to return clean air

to the room.

1. Turn power OFF. Unplug vacuum cord

from electrical outlet.

2. Locate filter behind the filter door on the

front of the vacuum. Remove and replace

when filter becomes dirty. The white,

pleated HEPA Media filter* is NOT washable.

3. Replace the door by inserting the tabs on

the left side and snapping the right side

into place.

Checking rotating floor

brush and drive belt

Check your vacuum’s rotating oor

brush and drive belt regularly for wear

or damage.

1. Turn power OFF. Unplug vacuum cord

from electrical outlet.

2. Place handle in low position and turn

vacuum over so bottom side is facing up.

3. Using a screwdriver, remove the four

screws and lift brush cover off.

4. Grasp rotating floor brush at both

ends and lift.

5. Clean strings, hair and other debris from

rotating floor brush, motor pulley, and

drive belt areas.

6. Check drive belt for wear, cuts, or

stressed areas.

7. Check air passageway for obstructions.

Remove debris from this area.

8. Reposition brush cover and fasten four

screws back into place.

pre-motor filter

HEPA Media filter*

*The filter media, not the vacuum as a whole,

complies with the IEST-RP-CC001.5 or the

EN-1822-1:2009 HEPA standard.

Maintenance and Care

Replace drive belt

1. Turn power OFF. Unplug vacuum cord from

electrical outlet.

2. With rotating brush removed (steps 1-4

of Check rotating floor brush and drive

belt), grasp old drive belt and remove from

motor pulley. Discard old drive belt.

3. Place new drive belt over motor pulley and

stretch other end over rotating floor brush

in the space between the bristles. Place

ends of rotating floor brush down into

slots.

4. Turn rotating floor brush by hand in the

direction of the motor pulley. If properly

installed, drive belt will center itself on

rotating brush.

5. Reposition brush cover and fasten four

screws back into place.

Clearing a Clog

Low suction or poor pickup may be due

to a clog in the vacuum. If you notice

a change in the sound of the vacuum

motor, check for clogs.

1. Turn power OFF. Unplug vacuum cord from

electrical outlet.

2. Empty Dirt Container.

3. Check upper tank and suction inlet

for clogs.

4. Grasp Quick Reach handle and remove

hose wand from base to check for clogs in

the base, the wand, and the hose.

5. Remove the screw attaching the hose wand

base to the vacuum. Straighten the hose

wand base and unclog, with long, narrow

object such as broom stick.

6. If the clog persists, follow steps for

checking rotating floor brush on page

10 and inspect the air passageway for

obstructions.

Maintenance and Care

TurboBrush® Tool

Maintenance select models only

1. Turn power OFF. Unplug vacuum cord from

electrical outlet.

2. Remove tool from hose or from clip on

vacuum handle.

3. Twist collar so opening is at the top and lift

clear cover to remove.

4. Remove brush from belt and clean debris.

5. Replace brush inside belt and place ends

into slots on the sides.

6. Reposition top cover making sure to line

up inside tab at the front with the opening

on the cover. Twist collar until opening is at

the bottom to lock into place.

Troubleshooting

Vacuum cleaner won’t turn on...

Possible causes Remedies

Power cord not plugged in Check electrical plug

Blown fuse/tripped breaker in home Check/replace fuse or reset breaker

Vacuum cleaner doesn't have good suction...

Possible causes Remedies

Hose not properly positioned Make sure hose is fully connected to base

and body. Be sure to hold onto plastic hose

collar while connecting hose.

Dirt tank not installed properly Check assembly of upper and lower portions,

correctly position and secure into place

Dirt tank is full Empty dirt tank

Clog in cleaner Follow instructions on pg. 10 and 11 for

clearing clogs

Filters are dirty Check and clean filter

Hose not properly attached Make sure hose collar is properly installed

Vacuum is not suctioning or blowing Make sure hose collar is properly installed

WARNING:

To reduce the risk of electric shock, turn power OFF and

disconnect polarized plug from electrical outlet before performing

maintenance or troubleshooting.

Other maintenance or service not included in the manual

should be performed by an authorized service representative.

Thank you for selecting a BISSELL brand

product.

If you should happen to need assistance during assembly

or operation, call BISSELL Consumer Service at 1-800-237-7691.

Please do not return this product to the store.

For any questions or concerns, BISSELL is happy to be of service.

Replacement parts - BISSELL Vacuum

Item Part No. Part Name

1 32074 Style 7/9/10/12 Drive Belt (2-Pack)

2 203-1056 Crevice Tool

3 203-1059 Combination Dusting Brush / Upholstery Tool

4 203-1068 Extension Wand

5a 203-8074 Hose Assembly (12B1 Series)

5b 203-8049 Hose Assembly (68C7 Series)

6a 203-8072 Brush Roll Assembly (12B1 Series)

6b 203-8045 Brush Roll Assembly (68C7 Series)

7a 203-7913 Pleated Circular Filter

7b 6046 Febreze Inner Circular Filter

8 203-1192 Foam Filter

9a 203-8037 Post Motor HEPA Media Filter* (68C7 Series)

9b 17T6 Febreze

Style 12 Filter (68C7 series)

9c 1602290 Post Motor Filter, Allergen, Style 12

10 203-1215 Pre-Motor Filter

11 203-7170 TurboBrush

Bracket

12 203-7171 TurboBrush

Tool

6a/6b

5a/5b

7a/7b 8 9a/9b/9c

11 12

2 3 4

*The filter media, not the vacuum as a whole, complies with the IEST-RP-CC001.5 or the

EN-1822-1:2009 HEPA standard.

Febreze® and related trademarks are owned by The Procter & Gamble Company, Cincinnati,

Ohio, and used under licensed by BISSELL Homecare, Inc.

Warranty - BISSELL Vacuum

This warranty gives you specific legal rights, and you may also have other rights which

may vary from state to state. If you need additional instruction regarding this warranty

or have questions regarding what it may cover, please contact BISSELL Consumer Care by

E-mail, telephone, or regular mail as described below.

Limited One Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identied below, upon receipt of

the product BISSELL will repair or replace (with new or remanufactured components or

products), at BISSELL’s option, free of charge from the date of purchase by the original

purchaser, for one year any defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service.

This warranty does not apply to fans or routine maintenance components such as

filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect,

unauthorized repair, or any other use not in accordance with the User's Guide is not

covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center

in your area.

If you need information about repairs or replacement parts, or if you have

questions about your warranty, contact BISSELL Consumer Care.

Website or E-mail:

www.bissell.com

Use the “Customer Support” tab.

Or Call:

BISSELL Consumer Care

1-800-237-7691

Monday - Friday 8 am - 10 pm ET

Saturday 9 am - 8 pm ET

Sunday 10 am - 7 pm ET

Or Write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids, MI 49501

ATTN: Consumer Care

BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY

NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL

NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or exclusion may not

apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL

OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW,

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF

PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty last so the

above limitation may not apply to you.

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

Grand Rapids, Michigan

Part Number 160-1867

Rev 05/13

Visit our website at:

www.bissell.com

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Care

1-800-237-7691

Monday - Friday 8 am - 10 pm ET

Saturday 9 am - 8 pm ET

Sunday 10 am - 7 pm ET

Or write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Care

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It

provides proof of purchase date in the event of a

warranty claim. See Warranty on page 15 for details.

BISSELL consumer care

www.bissell.com 800.237.7691

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

Bissell 1240 Series User manual

Brand: Bissell

Model: 1240 Series

Category: Vacuum cleaners

Type: User manual

This manual is also suitable for

Download PDF

report

Bissell 1240 Series User manual

This manual is also suitable for

Bissell 1240 Series User manual

Related papers

Other documents