Astonica 50103530 User manual

Brand: Astonica

Model: 50103530

Type: User manual

230910rev1

Read the instructions and precautions before use of this product

Please keep this instruction manual for future reference

Model No: 50103530

Superior Leisure 30"

Round Balcony Table

Instruction Manual

For warranty information, please refer to the back page of

this instruction manual.

Due to ongoing product development

the actual product or products may vary from

the illustrations or photos shown within this manual.

NOTE: This product is intended for residential, non-commercial use.

Made in China

Distributed by:

World Factory, Inc.

Westlake, TX 76262

For Manuals, Replacement Parts or Customer Service visit:

www.ezreplacement.com

Limited Warranty

World Factory, Inc. Products for Home Use

World Factory, Inc. (Seller) warrants to the original Buyer only, that each Astonica Product will be free

from defects in material and workmanship for a period of one (1) year from date of purchase.

SELLER’S SOLE OBLIGATION AND BUYER’S EXCLUSIVE REMEDY UNDER THIS LIMITED

WARRANTY SHALL BE THE REPAIR OR REPLACEMENT OF PARTS, WITHOUT CHARGE, WHICH

ARE DEFECTIVE IN MATERIAL OR WORKMANSHIP. ANY PARTS AS DETERMINED BY THE SELLER

WHICH HAVE BEEN MISUSED; ABUSED OR DAMAGED EITHER DIRECTLY OR INDIRECTLY FROM

REPAIRS OR ALTERATIONS ATTEMPTED BY UNAUTHORIZED PERSONS; IMPROPER

MAINTENANCE, NEGLECT OR ACCIDENT ARE NOT COVERED BY THIS LIMITED WARRANTY. This

warranty does not apply to damage, heat-induced coloration changes, scratching or alteration due to

normal use or weathering. To make a claim under this Limited Warranty, you must return the complete

product with proof of purchase, transportation prepaid, to any World Factory, Inc. authorized service

center. Call 1-888-422-7800 or visit: ezreplacement.com for the location of the nearest authorized

service center.

Additional Limitations

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY OR CONSUMABLE ITEMS RELATED

TO THIS PRODUCT. ALL IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE (1)

YEAR FROM DATE OF PURCHASE. IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF

PROFITS, ARISING FROM THE SALE OR USE OF THIS PRODUCT.

If any provision of this Limited Warranty is for any reason held to be invalid or unenforceable, such

provision shall not affect any other provision herein, this Limited Warranty shall be construed as if

such invalid and/or unenforceable provision had never been contained herein.

This warranty gives you special legal rights, and you may also have other rights which vary from state

to state.

This Warranty contains the entire agreement between Seller and Buyer and supersedes any and all

prior agreements, arrangements, or understandings between the parties relating to product warranty.

PARTS LIST

PART # DESCRIPTION QUANTITY

Carefully remove the contents from the package. If any parts are missing do not

attempt to use the product until they have been obtained and correctly installed.

ASSEMBLY INSTRUCTIONS

A Table Top 1

B Table Leg 4

C Center Brace 2

D Bolt 8

E Lock Washer 8

F Plastic Bolt Cover 8

G Hex Wrench 1

Figure 1

Parts Detail

CAUTION: Do not over tighten fasteners.

Install Table Legs

1. (SEE FIGURE 1) Place table top (A) upside down on ﬂat non-scratch surface.

2. Turn one table leg (B) upside down and insert leg into end cap ﬁttings as shown.

Repeat for three remaining table legs.

Install Upper Center Brace

1. Align one center brace (C) with upper mounting hole of the four table legs.

2. Place lock washer (E) onto bolt (D) and insert bolt with washer into upper mounting hole

of one table leg as shown.

3. Next, thread bolt through center brace (C). Using hex wrench (G), loosely tighten bolts.

Repeat step 2 and 3 for four remaining legs.

NOTE: Do not tighten bolts until all three legs are secure.

Install Lower Center Brace

1. Align remaining center brace (C) with lower mounting hole of the four table legs.

2. Place lock washer (E) onto bolt (D) and insert bolt with washer into lower mounting hole

of one table leg as shown.

3. Next, thread bolt through center brace (C). Using hex wrench (G), loosely tighten bolts.

Repeat step 2 and 3 for three remaining legs.

4. With both center braces (C) in place, tighten each bolt a few revolutions at a time,

alternating between bolts in a cross corner "X" fashion.

Table Leg Upper

Mounting Hole

Table Leg Lower

Mounting Hole

NOTE: Tightening every other bolt or in a cross fashion will ensure your table is level by

placing equal pressure on each joining bolt.

5. Cover all bolts with plastic bolt cap (F).

Your table is now ready to use.

(4 places)

Astonica 50103530 User manual

Astonica 50103530 User manual

Astonica 50103530 User manual

Related papers

Other documents