TECHNOLOGY
RCLL-1
SPECIFICATIONS
SETUP
Connectors: Gold plated RCA type line in and line out
Power Supply: 12 VDC (included)
The line level remote control is a versatile means of controlling a block amplifier fed by a line level source. The
level may be controlled from a remote location via an infrared repeating system or at the front of the unit via a
manual volume control setting. The front mounted manual volume setting may also be used as a limiter to prevent
the amplifier from being overdriven by sources with very high output when controlled remotely.
INSTALLATION MANUAL
AUDIOPLEX TECHNOLOGY
404 GWH P.O. BOX 440
MELVIN VILLAGE, N.H. 03850
1-800-257-2077 603-544-8601 FAX: 603-544-8901
www.audioplex.com
2006 - 2/1/06
Remote Controlled Line Level Volume Control
*ProScan is a registered trademark of Thomson Consumer Electronics.
1. Connect the line level source to the LINE IN jacks on the RCLL-1.
2. Connect the LINE OUT jacks to the destination equipment.
3. Connect the IR sensor eye (default) for local operation or the emitter output of an infrared repeating
system to the INFRARED IN. Signal connects to red, ground to black. A cable may be needed with
the appropriate plug (usually a 1/8” mono mini phone plug) to fit an IR connecting block, such as
the Audioplex IRStation.
4. Connect the 12 volt DC power supply to the 12 VDC jack and plug it
into a live 120 volt AC outlet.
5. Program your universal remote to transmit Proscan* audio codes.
OPERATION
1. Turn the VOLUME knob on the front of the RCLL-1 fully clockwise.
2. Be sure that the line level destination is on and turned to a normal level.
3. Start the line level source.
4 Point the remote at the repeating system target and press and hold the Volume Up button.
After about 10-15 seconds, the signal should begin to be received by the destination equipment.
As you continue to hold down the Volume Up button, the signal will gradually increase to maximum.
5.The signal can be smoothly decreased by pressing and holding the Volume Down button.
6. The signal can be muted by pressing the Mute button. Pressing Mute again will restore the signal
to its previous level.
7. Short presses of Volume Up and Down will cause the signal level to increase and decrease in
larger steps.
8. The Volume knob on the RCLL-1 can also be used to adjust signal level. Note that if this control
is turned down, the maximum remote level is reduced. This can be used to limit maximum volume.
WARRANTY
Your AUDIOPLEX TECHNOLOGY RCLL-1 is covered by a LIFETIME WARRANTY against any
defects in workmanship and materials. Any defects will be remedied without charge for labor or parts.
Damage incurred by shipping or accident is not considered to be a defect, and not covered by this
warranty. AUDIOPLEX TECHNOLOGY is not responsible for defective operation caused by abuse or by
modification or service by any unauthorized person or agency.
The unit must be properly installed and operated according to instructions for the warranty to apply. Any
necessary servicing must be done by AUDIOPLEX TECHNOLOGY. The products must be returned expenses
prepaid, with written authorization from the company. The product must be shipped with the proof of purchase
and in the original carton and packing material to avoid damage.
AUDIOPLEX TECHNOLOGY
404 GWH P.O. BOX 440
MELVIN VILLAGE, N.H. 03850
1-800-257-2077 603-544-8601 FAX: 603-544-8901
www.audioplex.com
2006 - 2/1/06
WIRING DIAGRAM
INFRARED
IN
LINE
IN
LINE
OUT
12 VDC
+
G
L
R
OPTIONAL
EMITTER
TO AMP
LINE OUT
TO AMP
LINE IN
56Khz IR Sensor
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Audioplex RCLL-1 Installation guide
-
-
-
-
-
-
-
-
-