2. Futaba
  3. SBS-01C

Futaba SBS-01C User manual

  • Hello! I am an AI chatbot trained to assist you with the Futaba SBS-01C User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
SBS-01C
Every time it's used, current
consumption is added to SBS-01C.
SBS-01C does not reset even if a
connection is removed or it is turned
off.
The consumption capacity returns
to 0. When you'd like to know the
FRQVXPSWLRQFDSDFLW\RIÀLJKWSOHDVH
UHVHWEHIRUHDÀLJKW
*Power supply off isn't done for 5
seconds after a reset. Because data
isn't preserved.
1M23N26733
5;6%86SRUW
%DWWHU\
(6&
5HVHWVZLWFK /('
9ROWDJHFDEOH
)XVH
ٛSDUWVٜ
+HDW6KULQN7XEH
)XVH
7R6%86SRUWRI
WHOHPHWU\UHFHLYHU
7R6%86RIUHFHLYHU
&XUUHQWFDEOH
3UHVVWKHUHVHWVZLWFK
ؙ:LULQJDQGFRQQHFWRUDUHQRWDWWDFKHG
8VHDFRQQHFWRUZLWKQRHOHFWULFDOSRZHUORVV
Please note that the proper default slot for
this accessory is number 24. This sensor
XVHVVORWVVWDUWLQJDW

     ,QIRUPDWLRQ RQ KRZ
WRFKDQJHWKHVORWDVVLJQPHQWLVLQFOXGHG
in the transmitter's manual.
7KDQN\RXIRUSXUFKDVLQJ)XWDEDV
SBS-01C Current Sensor. Please
UHDGWKLVPDQXDOWKRURXJKO\WR
ensure proper current sensor
SHUIRUPDQFH:HDOVRHQFRXUDJH
you to retain the manual for future
reference.
The SBS-01C will not function properly if
connected to an S.BUS port or other channel
ports.
As with any electronic components, proper
precautions are urged to prolong the life and
increase the performance of the SBS-01C.
If connected in reverse, explosions or fire
could occur.
If the connector works loose during
model operation, control will be lost and
cause the potential for extreme danger.
The SBS-01C can monitor and display
WKHLQIOLJKWFXUUHQW YROWDJHDQG FXUUHQW
consumption of the drive battery.
%DWWHU\
If close to a magnetic body, the DC current
may not be measured correctly.
There is danger of ignition and fire.
Do not use until inspection is complete.
The consumption capacity is indicated.
(It isn't the present battery capacity.)
SBS-01C may break down and fall.
There is danger of ignition and fire.
(6&
Voltage cable
Measure the cable and then cut it to the desired length.
Cut approximately 30mm of the black
ٕ
line from the cable.
Solder the fuse inline on the black
ٕ
wire and then reattach the section of wire
that was previously removed. The fuse should be attached as close to the
external power supply as possible.
Place a piece of heat shrink tubing over the fuse, ensuring that it covers the
soldered areas. Shrink the tubing snug to the fuse and the wire using a heat gun.
The cable should be connected as shown in the diagram below.
The manual for the Telemetry system should be referred to after the setup is
complete. Check to make sure it functions as desired and that it provides the
correct data on the display.
7KHIXVHVKRXOGEHDWWDFKHGDVFORVHWRWKH
H[WHUQDOSRZHUVXSSO\DVSRVVLEOH
+HDWVKULQNWXEH
)XVHWR%ODFNOLQHٕ
+HDWVKULQNWXEH
+HDWVKULQN
7KHFRQQHFWLRQLVDIIL[HGWRWKH(6&RQWKHZLUHV
WKDWDUHFRQQHFWHGWRWKHEDWWHU\E\VROGHULQJWKHP
DQGWKHQSURWHFWLQJWKHPZLWKKHDWVKULQN
7R3RZHU%DWWHU\
6%6&RQWKHOLQH
)XVHقPRXQWLQHLWKHUGLUHFWLRQك
)XVH
6ROGHUZHOGLQJ
)87$%$&25325$7,21
<DEXWVXND&KRVHLPXUD&KRVHLJXQ&KLEDNHQ-DSDQ
3KRQH)DFVLPLOH
©FUTABA CORPORATION 2016, 5 (1)
/