Allen-Bradley 140G-M-EOP User manual

Brand: Allen-Bradley

Model: 140G-M-EOP

Type: User manual

This manual is also suitable for

140G-M-ECOP

Allen-Bradley 140G-M-EOP is a motor-operated stored energy mechanism that can be used to remotely open or close circuit breakers. It has a rated service voltage of 24Vdc and an inrush power consumption of 300VA-W. The continuous service input is 150VA-W. The operating time is less than 0.1 seconds to open and 3 seconds to close. It has a minimum control impulse time of 0.15 seconds. The 140G-M-EOP can be used in a variety of applications, including:

Remotely opening or closing circuit breakers
Controlling access to electrical equipment
Providing safety interlocks
Automating processes

Remotely opening or closing circuit breakers
Controlling access to electrical equipment
Providing safety interlocks
Automating processes

WARNING: To prevent electrical shock, disconnect from power source before

installing or servicing. Install in suitable enclosure. Keep free from contaminants.

(Follow NFPA70E requirements).

AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o

manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.

(Seguire i requisiti NFPA70E).

WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur

Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem

passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen

Sie die Anforderungen nach NFPA70E).

AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation

secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée.

Protéger le produit contre les environnements agressifs. (Vous devez respecter la

norme NFPA70E).

ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o

del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.

Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E).

ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a

instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de

contaminantes. (Cumpra as exigências da norma NFPA70E).

Installation - Installazione - Instalación

Instalação - -

Control impulse minimum time 0,15s

Durata minima impulso di comando 0,15s

Mindestdauer des Steuerimpulses 0,15 s

Durée minimale de l'impulsion de commande 0,15s

Rated service voltage

Tensione nominale di impiego

Bemessungsbetriebsspannung

Tension assignée de service

Tensiòn nominal de servicio

Inrush power consumption

Potenza spunto

Leistungsaufnahme beim Anzug

Consommation à l’appel

Potencia absorbida al arranque

Continuous service input

Potenza in servizio

Leistungsaufnahme bei Dauerbetrieb

Consommation (service continu)

Potencia absorbida en servicio permanente

24 Vdc

48...60 Vdc

110...125 Vac/Vdc

220...250 Vac-Vdc

380 Vac

300 VA-W

150 VA-W

ON OFF

Riarmo / Reset

Rückstellung

Reset / Rearme

Operation time

Tempo di manovra

Schaltzeit

Temps de manoeuvre

Tiempo de maniobra

5 s3 s < 0.1 s

- Only for 140G-M-ECOP

- Solo per 140G-M-ECOP

- Nur für 140G-M-ECOP

- Uniquement 140G-M-ECOP

- Sólo para 140G-M-ECOP

DIR 1000479R0621 Version 01

Bul. 140G/140MG

DIR 1000479R0621 Version 01 - 140G-M-EOP_ , 140G-M-ECOP_

警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく

ださい。適切なケース内に取付けてください。また、汚染物質がないことを

確認してください。（NFPA70Eの要件に従ってください）

警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备

箱内。防止接触污染。符合NFPA70E要求）物

Label

Escutcheon

Screw

LENGTH dia.

25 mm (0.98") 5

LENGTH M

20 mm (0.79") M 4

Stored energy operating mechanism for 140G-M

Comando a motore ad accumulo di energia

Motorantrieb mit energiespeicherung

Commande par moteur a accumulation d’energie

Mando a motor con acumulacion de energia

3 4

1 2

(2)

CLACK

DIR 1000479R0621 Version 01

- Only for 140G-M-ECOP

- Solo per 140G-M-ECOP

- Nur für 140G-M-ECOP

- Uniquement 140G-M-ECOP

- Sólo para 140G-M-ECOP

- Do not insert when undervoltage/shunt release is mounted

- Nicht einschalten, wenn die undervoltage/shunt release montiert sind

- Non inserire nel caso sia montata la bobina di apertura/minima

- Ne pas insérer au cas où la undervoltage/shunt release sont montées

- No introducir en caso de que esté montada la undervoltage/shunt release

- For local/remote indication only

- Solo per la segnalazione elettrica

- Nur für elektrische Meldung

- Uniquement pour signalisation électrique

- Sólo para se

(3)

DIR 1000479R0621 Version 01

ONLY FOR 140G-M-ECOP

4.4 lb-in

ONLY FOR 140G-M-ECOP

(4)

ONLY FOR 140G-M-ECOP

0.5 Nm

DIR 1000479R0621 Version 01

- Do not insert when undervoltage/shunt release is mounted

- Nicht einschalten, wenn die undervoltage/shunt release montiert sind

- Non inserire nel caso sia montata la bobina di apertura/minima

- Ne pas insérer au cas où la undervoltage/shunt release sont montées

- No introducir en caso de que esté montada la undervoltage/shunt release

9.7 lb-in

ONLY FOR 140G-M-ECOP

(5)

ONLY FOR 140G-M-ECOP

1.1 Nm

DIR 1000479R0621 Version 01

LENGTH dia.

25 mm (0.98") 5

DISCHARGED

(6)

DIR 1000479R0621 Version 01

PULL

PUSH

9.7 lb-in

(7)

9.7 lb-in

ONLY FOR 140G-M-ECOP

1.1 Nm

DIR 1000479R0621 Version 01

LENGTH M

20 mm (0.79") M 4

(8)

9.7 lb-in

In=...A

APPLY LABEL

1.1 Nm

ONLY FOR DISASSEMBLING

DIR 1000479R0621 Version 01

(9)

= =

DIR 1000479R0621 Version 01

max #3 from dia. 0.16" to dia. 0.24"

max #3 from ø 4 mm to ø 6 mm

A B C

WITH ESCUTCHEON

5.84"

148.5 mm

5.94"

151 mm

2.98"

75.75 mm

WITHOUT ESCUTCHEON

5.59"

142 mm

5.59"

142 mm

2.80"

71.25 mm

Operating mode: Manual Operating mode: Auto

discharged springs

I: ON

charged springs

O: OFF

discharged springs

O: OFF

SNT / UVR / EL SNT

release tripping

OFF

pushbutton

on the

recharge

the springs

pushbutton

on the

discharged springs

I: ON

charged springs

O: OFF

discharged springs

O: OFF

SNT / UVR / EL SNT

release tripping

OFF

pushbutton

remotely

OFF pushbutton

remotely

pushbutton

remotely

motor

PULL

PUSH

MANU

AUTO

LEGEND LEGENDA ZEICHENERKLÄRUNG LÉGENDE LEYENDA

H = Signal lamp

H = Lampada di segnalazione

H = Signallampe

H = Voyant lumineux de signalisation

H = Lámpara de señalación

H = 信号指⽰灯

SO = Pushbutton or contact for opening the circuit-breaker

SO = Pulsante o contatto per l'apertura dell'interruttore

SO = Taster oder Schalter zum Öffnen des Leistungsschalters

SO = Bouton-poussoir ou contact pour l’ouverture du disjoncteur

SO = Pulsador o contacto para la apertura del interruptor

SO = 分断断路器的按钮或触头

SC = Button or contact for switch closing

SC = Pulsante o contatto per la chiusura dell'interruttore

SC = Drucktaster oder Kontakt für Schließen des Schalters

SC = Poussoir ou contact pour fermer le disjoncteur

SC = Pulsador o contacto para el cierre del interruptor

SC = 闭合断路器的按钮或触头

S3 = Change-over contact for electrical signalling of local/remote selector status

S3 = Contatto di scambio per la segnalazione elettrica di stato del selettore locale/remoto

S3 = Umschalter für die elektrische Zustandsmeldung des lokalen /fernen Wahlschalters

S3 = Contact inverseur pour signalisation électrique de etat de local/ déporté sélecteur

S3 = Contacto conmutado para señalización eléctrica de estado de local/remoto selector

S3 = 显⽰⼿动/⾃动（遥控）状态电⽓信号的辅助触头

C11

H SCSO

MANUAL

CONTROL

POWER

STORED ENERGY

MOTOR OPERATOR

140G-K-ECOP_

140G-K-EOP_

DIR 1000479R0621 Version 01 (L7944) - B0822

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 140G-IN032B-MU-P - April 2016

Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/

sustainability-ethics/product-environmental-compliance.page