Intellisystem IT-FHDCC59 User manual

IT-FHDCC59 Series

HD Video Camera

User Manual

1

Attentions

Electric Safety

Installation and operation must accord with electric safety standard

Caution to transport

Avoid stress, vibration and soakage in transport, storage and installation.

Polarity of power supply

The power supply of the product is ±12V; the max electrical current is 2A .Polarity of the power supply

drawing.

Careful of installation

Never move the camera by seizing the camera head. Do not rotate camera head by hand; otherwise,

mechanical trouble will occur.

This series item must put on the smooth desk or platform, and it cannot be installed slant ways;

If the camera is installed on TV or computer, the base can be fixed by four double-sided adhesive trays.

Do not apply in corrosive liquid, gas or solid environment to avoid the cover which is made up of organic

material.

To make sure no obstacle in rotation range.

Never power on before installation is completed.

Do not disassemble discretionarily.

We are not responsible for any unauthorized modification or dismantling.

Attention

Electromagnetic filed under certain rate may affect camera image!

2

Content

1. Fast Installation ...................................................................................................................................... 4

1.1 Camera Interface Explanation ....................................................................................................... 4

1.2 Power on Initial Configuration ....................................................................................................... 4

1.3 Video output .................................................................................................................................. 4

1.4 BRACKET MOUNTING ................................................................................................................. 4

2. Product overview .................................................................................................................................... 6

2.1 Product introduction ...................................................................................................................... 6

2.1.1 Product model ..................................................................................................................... 6

2.1.2 Dimension ............................................................................................................. 7

2.1.3 Accessory ............................................................................................................................ 8

2.2 Main Features ............................................................................................................................... 8

2.2.1 Camera performance .......................................................................................................... 8

2.2.2 Network performance .......................................................................................................... 9

2.3 Technical specification ................................................................................................................... 9

2.4 Interface instruction ..................................................................................................................... 11

2.4.1 External Interface .............................................................................................................. 11

2.4.2 Bottom DIP Switch ............................................................................................................ 12

2.4.3 Rotary Switch .................................................................................................................... 13

2.4.4 RS-232 interface ............................................................................................................... 13

3. Application Instruction .......................................................................................................................... 15

3.1 Video Output ............................................................................................................................... 15

3.1.1 Power-On Initial Configuration .......................................................................................... 15

3.1.2 Video output ...................................................................................................................... 15

3.2 Remote controller ........................................................................................................................ 16

3.2.1 Keys Instruction ............................................................................................................................... 16

3.2.2 Applications ....................................................................................................................... 17

3.3 MENU SETTING ......................................................................................................................... 19

3.3.1 Main menu ........................................................................................................................ 19

3.3.2 System setting................................................................................................................... 20

3.3.3 Camera setting .................................................................................................................. 20

3.3.4 P/T/Z ................................................................................................................................. 23

3.3.5 Video Format ..................................................................................................................... 24

3.3.6 VERSION .......................................................................................................................... 24

3.3.7 RESTORE DEFAULT ........................................................................................................ 25

4. Network Connection ...................................................................................................................... 25

4.1 Connecting Mode ................................................................................................................. 25

4.2 IE Log In ...................................................................................................................................... 28

4.2.1 Web client ......................................................................................................................... 28

3

4.2.2 Preview ............................................................................................................................. 28

4.2.3 Playback ........................................................................................................................... 29

4.2.4 Configuration ..................................................................................................................... 29

4.2.5 Video configuration ........................................................................................................... 30

4.2.6 Network configuration ....................................................................................................... 32

4.2.7 System configuration ......................................................................................................... 32

4.2.8 Logout ............................................................................................................................... 33

4.2.9 Wireless network ............................................................................................................... 33

5. Serial Communication Control .............................................................................................................. 35

5.1 VISCA protocol list ...................................................................................................................... 35

5.1.1 Camera return command .................................................................................................. 35

5.1.2 Camera control command ................................................................................................. 35

5.1.3,Inquiry command ............................................................................................................... 38

5.2,PELCO-D protocol command list ................................................................................................ 40

5.3 PELCO-P protocol command list ................................................................................................. 41

6. Camera Maintenance and Troubleshooting .......................................................................................... 42

6.1 Camera Maintenance .................................................................................................................. 42

6.2 Troubleshooting ........................................................................................................................... 42

4

1. Fast Installation

1.1 Camera Interface Explanation

1. Camera lens

2. Camera base

3. Remote Controller Receiver light

4. Bottom DIP switch

5. Tripod screw hole

6. Installation Orientation Hole

7. Rotary Switch: Video format select

8. RS232 control interface (input )

9. RS232 control interface (output )

10. RS485 input (left +,right-)

11. Audio Input interface

12. HD-SDI interface

13. DVI-I interface(including HDMI signal)

14. 10/100M Network interface

15. DC12V Input Power Supply Socket

Figure 1.2. Interface of U3 (USB3.0) series

1. Camera lens

2. Camera base

3. Remote Controller Receiver light

4. Bottom DIP switch

5. Tripod screw hole

6. Installation Orientation Hole

7. RS232 control interface (input )

8. 10/100M Network interface

9. DVI-I interface(including HDMI signal)

10. USB3.0 interface

11. DC12V Input Power Supply Socket

12. Power indicator

1.2 Power on Initial Configuration

1) Power on: connect DC12V power supply adapter showed in Figure1.1or NO.15.

2) Initial configuration: Power on with power indicator light on and remote control receiver light blinking, camera head

moves from bottom left to the bottom, and then go to the HOME position (intermediate position of both horizontal and

vertical ),while the camera module stretches. When remote control receiver light stops blinking, the self-checking is finished

Note: If you set preset 0, when Power on initial configuration is completed, the camera automatically moves to the preset 0

position.

1.3 Video output

This series has a variety of video output，such as LAN, DVI (HDMI) and 3G-SDI outputting.

1) video output from LAN

a. Network cable connection port: shown in Figure1.1, No.14.

b. Webpage Login: open your browser and enter 192.168.5.163 in the address bar (factory default); press Enter to enter

into the login page; click on the “player is not installed, please download and install!" and follow the installation steps

for installation. Then enter the user name admin and password admin (factory default); press Enter to enter into the

preview page, users can carry out PTZ control, video recording, playback, configuration and other operations.

2) DVI(HDMI) video output

a. DVI video cable connection: ST models refer to No.13 in Figure1.1; U3 models refer to No. 9 in Figure1. 2.

b. Connect the camera and the monitor via DVI video cable; video output is available after camera initial configuration.

3) 3G-SDI video output

a. 3G-SDI video cable connection: ST models refer to No.12 in Figure1.1,U3 models do not have 3G-SDI interface.

b. Connect the camera and the monitor via 3G-SDI video cable; video output is available after camera initial

configuration.

4) USB3.0 video output

a. USB3.0 video cable connection: ST models do not have USB3.0 interface. U3 models refer to NO.10 in figure1.2.

b. Connect the camera and the monitor via USB3.0 video cable, open video display software, select image device, and

then video output will be available.

5) USB3.0 compatible with USB2.0 output

a. USB 3.0 video cable connection: ST models do not have USB3.0 interface. U3 models refer to NO.10 in Figure1. 2.

b. Connect the camera and the monitor via USB3.0 video cable, open video display software, select image device, and

then video output will be available.

Note: USB2.0 output and USB3.0 output is the same interface.

1.4 Bracket Mounting

1) Bracket installation steps

2) Upside-down installation steps

2. Product overview

2.1 Product introduction

2.1.1 Product model

There are two main series according to different video output interface, ST (standard) and U3 (USB3.0 output).

Model NO.X — XXX — XXX — XX

IR ---IR remote controller

WR---wireless remote controller

ST---standard interface (optional 5G Wi-Fi function)

U3---USB3.0 interface

12---12x optical zoom lens

20---20x optical zoom lens

30---30x optical zoom lens

S---1080P60 downward compatibility

M---1080P30downward compatibility

Please refer to corresponding features in this manual.

Note: 5GWi-Fi is optional for ST (standard) series only.

2.1.2 Dimension

Figure 2.2 Camera dimension

2.1.3 Accessory

When you unpack, check that all the supplied accessories are included:

Model NO.

ST Series

U3 Series

Accessory

Standard

Power adapter 1pcs

RS232 cable 1pcs

User manual 1

Double-side glue shim 4pcs

Warranty card 1pcs

Optional

IR Remote controller 1pcs

Wireless controller 1pcs

Cascade Cable 1pcs

USB3.0 cable

Wall mounting bracket

Wall mounting bracket (optional)

Upside-down mounting bracket

(optional)

Upside-down mounting bracket

(optional)

2.2 Main Features

2.2.1 Camera performance

This series camera offers perfect functions, superior performance and rich interfaces. The features include advanced ISP

processing algorithms to provide vivid images with a strong sense of depth, high resolution and fantastic color rendition. It

supports H.264/H.264+ encoding which makes motion video fluent and clear even with less than ideal bandwidth

conditions.

1.Superb high-definition image: It employs 1/2.8 inch high quality CMOS sensor. Resolution is up to 1920x1080 with

frame rate up to 60 fps.

2. Various optical zoom lens: It has 12X/20X/30X optical zoom lens for options. The 12x zoom lens is with 72.5 ° wide

view angle without distortion.

3. Leading Auto focus technology: Leading auto focus algorithm makes lens a fast, accurate and stable auto-focusing.

4. Low noise and High SNR: Low Noise CMOS effectively ensure high SNR of camera video.

Advanced 2D/3D noise reduction technology is also used to further reduce the noise, while ensuring image sharpness.

5. Quiet PTZ: By adopting high accuracy step driving motor mechanism, it works extremely quiet and moves smoothly and

very quickly to designated position.

6. Multi-Format Video Outputs: support DVI (HDMI), 3G SDI, USB, wired LAN and wireless LAN interfaces

The 3G-SDI is available for 100m transmission at 1080p60 format.

7. Multiple remote controls: There is IR remoter and 2.4G wireless remote for options. The 2.4G wireless remote

controller will not be affected by angle, distance or IR interference. Support transparent transmission function.

8. Low-power sleep function: Support low-power sleep/wake up, the consumption is lower than 500mW under sleep

mode

9. Support Multiple Control Protocol: Support VISCA,PELCO-D,PELCO-P protocols which can also be automatically

recognized. Support VISCA control protocol through IP port.

10.RS-232 cascade function: ST series support RS-232 cascade function which is convenient for installing.

11. 255 presets positions: Up to 255 presets (10 presets by remoter).

12. Wide application: tele-education, lecture

capture,Webcasting,Videoconferencing,Tele-training,Tele-medicine,Interrogation and Emergency

command systems.

2.2.2 Network performance

1. Audio Input Interface: Support 16000,32000,44100,48000 sampling frequency and AAC,MP3,PCM audio coding.

2. Multiple Audio/Video compression: Support H.264/H.265 video compression; AAC,MP3 and PCM audio

compression; Support compression of resolution up to 1920x1080 with frame up to 60 fps and 2 channel 1920x1080p

with 30 fps compression.

3. Multiple network protocol: Support ONVIF,RTSP,RTMP protocols and RTMP push mode, easy to link streaming

media server (Wowza, FMS)

4. 5G WI-FI function: If the product contains 5G Wi-Fi module, you can set up a wireless Wi-Fi connection in a webpage,

the specific configuration described in detail on the page of web configuration.

2.3 Technical specification

Model

IT-FHDCC59-12

IT-FHDCC59-20

IT-FHDCC59-30

Camera Parameter

Optical Zoom

12X

f＝3.9～46.1mm

20X

f＝5.57～110mm

30X

f＝4.3～129mm

Sensor

1/2.8 inch high quality HD CMOS sensor

Effective Pixels

16: 9 2.07 megapixel

Video Format

DVI（HDMI）/SDI video format

1080P60/50/30/25/59.94/29.97;1080I60/50/59.94;720P60/50/30/25/59.94/29.97

Interface video format (U3)

1) U3: 1920X1080P 60/50/30/25;1280X720P 60/50/30/25; 960X540 P30;640X360

P30 ;640X480 P30 ;352X288 P30 ;960X540 P30

2) U3 compatible with U2 :960X540 P30; 640X360 P30; 1280X720 P10/15; 720X576

P50; 720X480 P60; 640X480 P30; 352X288 P30.

View Angle

6.3°(tele)--72.5°(wide)

3.3°(tele)--54.7°(wide)

2.34°(tele)--65.1°(wid

e)

AV

F1.8 ～ F2.4

F1.6 ～ F3.5

F1.6 ～ F4.7

Digital Zoom

10X

Minimum Illumination

0.5Lux (F1.8, AGC ON)

DNR

2D & 3D DNR

White Balance

Auto / Manual/ One Push/ 3000K/ 4000K/5000K/6500K

Focus

Auto/Manual

Aperture

Auto/Manual

Electronic Shutter

Auto/Manual

BLC

ON/OFF

WDR

OFF/ Dynamic level adjustment

Video Adjustment

Brightness, Color, Saturation, Contrast, Sharpness, B/W mode, Gamma curve

SNR

>55dB

Input / Output Interface

Video Interfaces

IT-FHDCC59-12/20/30-ST

Model:3G-SDI,DVI(HDMI),LAN,RS232(IN/OUT),RS485,A-IN

IT-FHDCC59-12/20/30-U3 Model:USB3.0,DVI(HDMI),LAN,RS232(IN)

Image Code Stream

Dual stream output

Video Compression Format

H.264, H.265

Control Signal Interface

RS-232 Ring through RS232 output

Control Protocol

VISCA/PELCO-D/PELCO-P; Baud Rate: 115200/9600/4800/2400bps

Audio Input Interface

Double track 3.5mm linear input;

Audio Compression Format

AAC/MP3/PCM Audio compression

HD IP Interface

100M IP port(100BASE-TX); 5G Wi-Fi (optional),

Support Visca protocol control through IP port.

Network Protocol

RTSP/RTMP,ONVIF,GB/T28181

Power Interface

HEC3800 outlet (DC12V)

PTZ Parameter

Pan Rotation

±170°

Tilt Rotation

-30°～+90°

Pan Control Speed

0.1 -100°/sec

Tilt Control Speed

0.1-45°/sec

Preset Speed

Pan: 100°/sec, Tilt: 45°/sec

Preset Number

255 presets (10 presets by remote controller)

Other Parameter

Supply Adapter

AC110V-AC220V to DC12V/1.5A

Input Voltage

DC12V±10%

Input Current

1A(Max)

Consumption

12W (Max)

Store Temperature

-10℃～+50℃

Store Humidity

20% - 95%

Working Temperature

-10℃～+50℃

Working Humidity

20%--80%

Dimension

258mmX172mmX168mm

Weight

1.54KG

Remote Operation (IP)

Remote Upgrade, Reboot and Reset

Accessory

power supply,RS232 control cable, remoter, manual, warranty card, bracket

(optional)

2.4 Interface instruction

2.4.1 External Interface

1) External interface of ST models: Rotary switch, RS232 input output,RS485 input, audio input,3G-SDI output, DVI

（HDMI）output,LAN,DC12V power interface.

Figure 2.3 ST model external interface diagram

2) External interface of U3 model: RS232 input, LAN, DVI（HDMI）output,USB3.0 output,DC12V power interface.

Figure 2.4 U3 model external interface diagram

2.4.2 Bottom DIP Switch

ST model and U3 model Bottom DIP Switch diagram shown in Figure 2.5:

Figure 2.5 Bottom DIP Switch diagram

ST model two DIP switches are set to ON or OFF to select different modes of operation as shown in Table 2.2

Table 2.2 DIP Switch setting

U3 model two DIP switches are set to ON or OFF to select different modes of operation as shown in Table 2.3

Table 2.3 DIP Switch setting

Note: Working mode can be applicable for web upgrade.

No.

SW2

SW1

Explanation

1

OFF

Software upgrade mode

2

ON

Working mode

No.

SW2

SW1

Explanation

1

ON

OFF

Working mode

2

ON

USB3.0 software upgrade mode

3

OFF

ON

ARM software upgrade mode

2.4.3 Rotary DIP Switch

Sixteen rotary DIP 0-F interface diagram shown in Figure 2.6;

Sixteen rotary DIP 0-F corresponding to the video format as shown in Table 2.4:

Note: ST model have rotary DIP; U3 model is without rotary DIP.

Figure 2.6 Rotary Dial diagram

Table 2.4 Rotary Dial corresponding to the video formats

Dial-up

video format

Dial-up

video format

0

1080P60

8

720P30

1

1080P50

9

720P25

2

1080I60

A

1080P59.94

3

1080I50

B

1080I59.94

4

720P60

C

720P59.94

5

720P50

D

1080P29.97

6

1080P30

E

720P29.97

7

1080P25

F

Display the video

format set on the

menu

Note: 1. After switching DIP, you need to restart the camera to take effect.

2. Only when the rotary dial code is F, the video format is displayed on the menu item.

3. Rotary switch setting is 0-E, rotary switch setting decides video format.

2.4.4 RS-232 interface

1) ST model RS-232C interface specification as shown below

Computer or keyboard and camera connection method

Camera

WindowsDB-9

1.DTR

1.DCD

2.DSR

2.RXD

3.TXD

4.GND

4.DTR

5.RXD

5.GND

6.GND

6.DSR

7.IR OUT

7.RTS

8.NC

8.CTS

9.RI

2) RS-232 Mini-DIN 8-pin Port Definition

3) RS232 (DB9) Port Definition

4) VISCA networking as shown below:

Camera cascade connection method

Camera 1

Camera 2

1.DTR

2.DSR

3.TXD

4.GND

5.RXD

6.GND

7.IR OUT

7.OPEN

8. NC

8.OPEN

Note: ST model has RS232 input and output interface,so you can cascade as the above way;

It won’t work for U3 model,since U3 model only has RS232 input interface.

NO.

Port

Definition

1

DTR

Data Terminal Ready

2

DSR

Data Set Ready

3

TXD

Transmit Data

4

GND

System Ground

5

RXD

Receive Data

6

GND

System Ground

7

IR OUT

IR Commander Signal

8

NC

No Connection

NO.

Port

Definition

1

DCD

Data Carrier Detect

2

RXD

Receive Data

3

TXD

Transmit Data

4

DTR

Data Terminal Ready

5

GND

System Ground

6

DSR

Data Set Ready

7

RTS

Request to Send

8

CTS

Clear to Send

9

RI

Ring Indicator

3. Application Instruction

3.1 Video Output

3.1.1 Power-On Initial Configuration

Connecting the power, camera will have initial configuration, IR indicator light will be flashing. When the camera return to

the HOME position (middle position for P/T), and lens finish zoom in/out, the auto-testing is finished. IR led will also stop

flashing. If the preset 0 is set, camera will rotate to the 0 preset position after initial configuration.

3.1.2 Video output

Connect to the video output cable: the user select the output mode according to the machine model.

Figure 1.4.1 is for your reference (output interface introduction for each product)

1) Network output: connect this product and your computer through network cable, then open the browser, enter the

camera IP address (factory default 192.168.5.163) in the address bar, then to the login page and input a user name

and password (factory default are “admin”) ,Finally enter the preview page, and the image comes out.

(Note: If you forget your user name, password, IP address, you can manually restore the default by the remote

controller key combination * #)

2) 3G-SDI output or DVI (HDMI) output: Connect the monitor with the corresponding video output interface, then the

monitor output image.

3) USB3.0 output: Connect this product with computer USB3.0 interface (blue), open the Device Manager to see

whether there is an image device and whether the Universal Serial Bus controllers recognize USB3.0 device. After

properly identified, open the software, choose the image device and then it will output image.

4) USB3.0 compatible with USB2.0 output: Connect this product with computer USB2.0 interface (black), open the

Device Manager to see whether there is an image device and whether the Universal Serial Bus controllers recognize

USB3.0 device. After properly identified, open the software, choose the image device and then it will output image.

3.2 Remote controller

3.2.1 Keys Instruction

1. Standby key

After 3S long press, the camera will step into standby mode. Long press 3S again, the

camera will initial configuration again and back to HOME position. (Note: If power-on mode

is turned on and Preset 0 is set, and there is no operation within 12s,it will automatically

point to the specified preset position.

2. Camera address selection

Select the camera address which wants to be controlled

3. Number key

Set or run 0-9 presets

4,*,# key

Key combination use

5. Focus control key

Auto focus: Enter into auto focus mode.

Manual focus: The camera focus mode is manual

Switch the camera focus mode to manual focus by pressing [focus +] or [focus -] to adjust.

6. Zoom Control key

zoom＋:Lens near

zoom－:Lens far

7. Set or clear preset key:

Set preset: Set preset key + 0-9 number key:

Clear preset key: Clear preset key + 0-9 number key

8. pan/tilt control key

Press key :Up

Press key :Down

Press key :Left

Press key: Right

“HOME” key: Return to the middle position or enter into the next level menu

9,BLC control key

Back light ON / OFF: Turn on or off the back light

10. Menu setting

Open or close the OSD menu

Enter / exit the OSD menu or return to the previous menu.

11. Camera IR remote control address setting

【*】+【＃】+【F1】:Camera Address No.1

【*】+【＃】+【F2】:Camera Address No. 2

【*】+【＃】+【F3】:Camera Address No. 3

【*】+【＃】+【F4】:Camera Address No. 4

12. Key combination Functions

1) 【#】+【#】+【#】:Clear all presets

2) 【*】+【#】+【6】:Restore factory defaults

3) 【*】+【#】+【9】:Flip switch

4) 【*】+【#】+ Auto: Enter into the aging mode

5) 【*】+【#】+【3】:Menu set to Chinese

6) 【*】+【#】+【4】:Menu set to English

7) 【*】+【#】+Manual: Restore the default user name,

password, and IP address

8) 【#】+【#】+【0】:Switch the video format to 1080P60

9)【#】+【#】+【1】: Switch the video format to 1080P50

10)【#】+【#】+【2】:Switch the video format to 1080I60

11)【#】+【#】+【3】:Switch the video format to 1080I50

12)【#】+【#】+【4】:Switch the video format to 720P60

13)【#】+【#】+【5】:Switch the video format to 720P50

14)【#】+【#】+【6】:Switch the video format to 1080P30

15)【#】+【#】+【7】:Switch the video format to 1080P25

16)【#】+【#】+【8】:Switch the video format to 720P30

17)【#】+【#】+【9】:Switch the video format to 720P25

3.2.2 Applications

Finishing initialization, it can receive and execute the IR commands. Press the remote controller button, the indicator

light is flashing; release the button, the indicator light stops flashing. Users can control the pan/tilt/zoom, setting and

running preset positions via the IR remote controller.

Key Instruction:

1. In this instruction, “press the key” means a click rather than a long-press, and a special note will be given if a

long-press for more than one second is required.

2. When a key-combination is required, do it in sequence. For example, “【 *】+【#】+【F1】”means press“【*】”first and

then press“【#】” and last press“【F1】”.

1) Camera Selection

Select the camera address to control.

2) Pan/Tilt Control

Up: press Down: press

Left: press Right: press

Back to middle position: press“【HOME】”

Press and hold the up/down/left/right key, the pan/tilt will

keep running, from slow to fast, until it runs to the endpoint;

the pan/tilt running stops as soon as the key is released.

3) Zoom Control

ZOOM IN: press “ZOOM “ key

ZOOM OUT: press “ZOOM ” key

Press and hold the key, the camera will keep zooming in or

zooming out and stops as soon as the key is released.

4) Focus Control

Focus (near):Press ”【focus+】” key (Valid only in manual

focus mode)

Focus (far): Press “【focus-】“key (Valid only in manual focus

mode)

Auto Focus: Support

Manual Focus: Support

Press and hold the key, the action of focus will keep

continue and stops as soon as the key is released.

5) BLC Setting

BLC ON / OFF: support

6) Presets setting, Running, clearing

1. Preset setting: to set a preset position, the users should

press the “【SET PRESET】” key first and then press the

number key 0-9 to set a relative preset,

Note: 10 preset positions in total are available by

remote controller.

2. Preset Running: Press a number key 0-9 directly to run

a relative preset.

Note: Action in vain, if a relative preset position is not

existed.

3. Preset clearing : to clear a preset position, the user can

press the “【CLEAR PRESET】” key first and then press the

number key 0-9 to clear the relative preset;

Note: press the“【#】” key three times continually to

cancel all the presets.

7) Camera Remote Controller Address Setting

【*】+【＃】+【F1】:Camera Address No.1

【*】+【＃】+【F2】:Camera Address No. 2

【*】+【＃】+【F3】:Camera Address No. 3

【*】+【＃】+【F4】:Camera Address No. 4

Page is loading ...

Intellisystem IT-FHDCC59 User manual

This manual is also suitable for

Intellisystem IT-FHDCC59 User manual

Related papers

Other documents