WaterWorks CEKM30 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 1 OF 6 | UPDATED ON 8.19.2021
STYLE No. CEKM30, CE30KM
Canteen One Hole Integrated Pull Spray
Kitchen Faucet with Oak Lever Handle
MOUNTING
SURFACE
Ø 2-1/8"
[54mm]
FITTINGS
HOLE
1/4" MIN
[6mm]
2-1/4" MAX
[57mm]
DECK
THICKNESS
INSTALLATION GUIDELINES
IMPORTANT:
To ensure this product is installed properly, you must read and follow
these guidelines.
The owner/user of this product must keep this information for future
reference.
This product must be installed by a professional licensed contractor.
Be sure your installation conforms to federal, state, and local codes.
In the State of Massachusetts, all installations must comply with the
rules and regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts required for
proper installation. Product is sold partially assembled but shown
fully disassembled for illustrative and service purposes only.
Use only a strap wrench or protected/smooth-jaw wrench on any
finished surface.
The use of certain plumber’s putty may stain stone or tile surfaces.
If further assistance is required, please contact Product Support at
1-800-927-2120 Monday through Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for available
replacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
ADJUSTABLE VERSUS FIXED SPRAY ADJUSTABLE
HANDLE TURN ANGLE TILT AND TURN
INLET CONNECTION 3/8” COMPRESSION CONNECTOR HOSES †
SPOUT REACH 9-1/8” [231mm]
SPOUT SWIVEL YES
SPRAY HOSE LENGTH 79” [2m]
SPRAY INCLUDED IN UNIT YES
WATER PRESSURE 85psi [6.0 bar] MAX
20psi [1.5 bar] MIN
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
† UK Style No., CE30KM is supplied with 2 BSPP adapters, assembly required.
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 2 OF 6 | UPDATED ON 8.19.2021
STYLE No. CEKM30, CE30KM
Canteen One Hole Integrated Pull Spray
Kitchen Faucet with Oak Lever Handle
INSTALLATION GUIDELINES
1. Unthread and remove the NUT from the SPOUT SHANK
then remove the PLASTIC and RUBBER WASHERS.
NOTE: Do NOT remove the RUBBER WASHER beneath
the ESCUTCHEON.
2. Thread and securely tighten the SUPPLY HOSES onto the
SUPPLY TUBES pre-installed on the SPOUT.
NOTE: The HOSES are M10 x 3/8” COMPRESSION
CONNECTOR HOSES and the SUPPLY TUBES are marked
BLUE for cold and RED for hot.
3. Insert the SPOUT through the hole on the mounting
surface making sure the RUBBER WASHER provided is
beneath the ESCUTCHEON and the HANDLE is aligned on
the RIGHT SIDE of the SPOUT.
NOTE: The HANDLE can ONLY be installed on the RIGHT
SIDE.
RUBBER WASHER
[DO NOT REMOVE]
SPOUT SHANK
RUBBER WASHER
PLASTIC WASHER
NUT
SUPPLY TUBE
[BLUE LABEL]
SUPPLY TUBE
[RED LABEL]
SUPPLY
HOSE SPRAY
SUPPLY HOSE
SUPPLY
HOSE SPRAY
SUPPLY HOSE
SUPPLY HOSE
MOUNTING
SURFACE
RUBBER WASHER
ESCUTCHEON †
HANDLE ‡
[RIGHT
SIDE ONLY]
SPRAY
SUPPLY HOSE
SUPPLY HOSE
MOUNTING
SURFACE
RUBBER WASHER
ESCUTCHEON †
HANDLE ‡
[RIGHT
SIDE ONLY]
† A RUBBER WASHER for the
ESCUTCHEON is provided.
If desired, a bead of caulk or clear
silicone may be applied where the
ESCUTCHEON contacts the
mounting surface.
‡ RIGHT HAND HANDLE
INSTALLATION ONLY
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 3 OF 6 | UPDATED ON 8.19.2021
STYLE No. CEKM30, CE30KM
Canteen One Hole Integrated Pull Spray
Kitchen Faucet with Oak Lever Handle
INSTALLATION GUIDELINES
6. Thread and securely tighten the FEMALE END of the
NYLON SPRAY HOSE onto SPRAY SUPPLY HOSE using
the ADAPTER provided.
NOTE: A FLOW REGULATING CHECK VALVE is located
inside the ADAPTER as well as an additional CHECK
VALVE.
5. Unthread and remove the CAP from the top of the SPOUT
then insert the MALE END of the NYLON SPRAY HOSE
through the bottom of the SPOUT and, from above,
manually guide the HOSE out of the SPOUT.
4. Slide the WASHERS and NUT over the HOSES then thread
and securely tighten the NUT onto the SPOUT SHANK.
SPOUT
SHANK
RUBBER
WASHER
PLASTIC
WASHER
NUT
SUPPLY HOSE
SPRAY
SUPPLY HOSE
NYLON
SPRAY HOSE
SPOUT
NYLON
SPRAY HOSE
[MALE END]
CAP
NYLON
SPRAY HOSE
SPOUT
NYLON
SPRAY HOSE
[MALE END]
CAP
1.
3.
2.
[GUIDE HOSE MANUALLY!]
SPRAY SUPPLY
HOSE
ADAPTER
NYLON SPRAY HOSE
[FEMALE END]
FLOW
REGULATING
CHECK
VALVE CHECK
VALVE
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 4 OF 6 | UPDATED ON 8.19.2021
STYLE No. CEKM30, CE30KM
Canteen One Hole Integrated Pull Spray
Kitchen Faucet with Oak Lever Handle
INSTALLATION GUIDELINES
7. Connect the SUPPLY HOSES to the SUPPLY VALVES [sold
separately].
NOTE: The HOSES are connected to SUPPLY TUBES that
are marked BLUE for cold and RED for hot.
8. Turn on the water and operate the HANDLE to ensure
it functions properly and to flush out any debris in the
supply lines then check all connections for leaks and turn
off the water.
CAUTION: Flush out the supply lines prior to installing the
SPRAYER.
9. Unthread and remove the COLLAR from the SPRAYER
inlet then slide the COLLAR over the SPRAY HOSE.
SUPPLY HOSE ‡
SUPPLY HOSE ‡
SUPPLY VALVE
[SOLD SEPERATELY]
UK INSTALLATIONS ONLY!
2 BSPP ADAPTERS, 9/16"-24 UNEF Male x 3/8" Female BSPP,
for the SUPPLY HOSES are provided.
‡
HANDLEHANDLE
COLD
HOT
OFF
[CHECK FOR LEAKS!]
ON
* TURN ON THE WATER
COLLAR
SPRAYER
NYLON
SPRAY HOSE
[MALE END]
COLLAR
COLLAR
SPRAYER
NYLON
SPRAY HOSE
[MALE END]
COLLAR
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 5 OF 6 | UPDATED ON 8.19.2021
STYLE No. CEKM30, CE30KM
Canteen One Hole Integrated Pull Spray
Kitchen Faucet with Oak Lever Handle
INSTALLATION GUIDELINES
10. Thread and securely tighten the SPRAY HOSE into the
SPRAYER using the RUBBER WASHER provided then
thread and securely tighten the COLLAR back onto the
SPRAYER.
12. Align and press the two halves of the WEIGHT over the
SPRAY HOSE in the desired position then thread and
securely tighten the SCREWS provided.
11. Insert the SPRAYER into the SPOUT then thread the CAP
back onto the top of the SPOUT.
NOTE: Ensure the PIN at the base of the SPRAYER fits
properly into the NOTCH on the SPOUT.
SPRAYER
RUBBER
WASHER
NYLON SPRAY HOSE
[MALE END]
COLLAR
SPRAYER
RUBBER
WASHER
NYLON SPRAY HOSE
[MALE END]
COLLAR
CAP
SPRAYER
CAP
SPRAYER
NYLON SPRAY HOSE
WEIGHT
SCREWS
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM PAGE 6 OF 6 | UPDATED ON 8.19.2021
STYLE No. CEKM30, CE30KM
Canteen One Hole Integrated Pull Spray
Kitchen Faucet with Oak Lever Handle
INSTALLATION GUIDELINES
13. Turn on the water and operate the SPRAYER to ensure
it functions properly making sure the WEIGHT can move
freely beneath the cabinet and the SPOUT is able to swivel
properly. Adjust the position of the WEIGHT if necessary.
NOTE: To adjust the SPRAY, press and hold the BUTTON
on the side of the SPRAYER.
SERVICING THE CARTRIDGE:
1. Unthread the GLAND COVER to expose the SET SCREW
then loosen, but do NOT remove, the SET SCREW using a
2mm HEX KEY.
2. Remove the HANDLE then unthread and remove the
RETAINING COLLAR to exposed and remove the
CARTRIDGE.
SPOUT
[180° SWIVEL]
BUTTON
[PUSH AND HOLD TO
ADJUST SPRAY]
HANDLE
WEIGHT
[ADJUST POSITION
IF OBSTRUCTED]
SPRAYER
SPOUT
[180° SWIVEL]
BUTTON
[PUSH AND HOLD TO
ADJUST SPRAY]
HANDLE
WEIGHT
[ADJUST POSITION
IF OBSTRUCTED]
SPRAYER
* TURN ON THE WATER
SET SCREW
[2mm HEX]
GLAND
COVER
HANDLE
SET SCREW
[2mm HEX]
GLAND
COVER
HANDLE
CARTRIDGE
RETAINING
COLLAR
GLAND
COVER
HANDLE
-
1
-
2
-
3
-
4
-
5
-
6
WaterWorks CEKM30 Installation guide
- Category
- Sanitary ware
- Type
- Installation guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
WaterWorks HNKM70 Installation guide
-
-
-
-
-
-
-
-
-