Super Circuits DMR16CD-3 User manual

DVQ4CD-3 DMR8CD-3

DMR16CD-3

User Guide

Volume

1

SUPER/CIRCUITS

DVQ-4CD-3, DMR8-CD3, DMR16CD3/ USER

MANUAL

11000 NORTH MOPAC EXPRESSWAY

SUITE 300

Austin, TX 78759

Phone 800-335-9777 • Fax 866-2567-9777

Please read instructions thoroughly before operation and retain it for future reference

The product specifications and information may be updated without notification.

RISK OF EL ECTRIC SHOCK. WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NON SERVICEABLE PARTS INSIDE PLEASE REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL

All the safety and operating instructions should be read before operation. Improper

operation may cause permanent damage.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance-(servicing) instructions in the literature accompanying the

appliance.

• Use provided adapter.

• Handle equipment with care.

• Do not expose this equipment to open sunlight.

• Do not spill liquid on equipment. Do not use this equipment near water.

• Please power down the unit before unplugging.

• Do not Power on & off quickly (Give unit 15 to 30 seconds when powering off & on).

• Service and Installation should be made by a qualified service technician.

• For your safety, unplug the power before moving, installing, or replacing components.

• Make sure all the power cable and wires are properly installed before operating.

• Avoid dramatic temperature changes, dust, and humidity.

• Operating temperature ranges are from 5C~40C. (41 to 104 degree Fahrenheit.)

• Keep this unit in a well-ventilated place and away from any heat-generating objects.

• Do not block the fan and vent areas.

4

Table of Contents

Date: 2007/12/02 VER: 1

PRODUCT OVERVIEW………………………………………………………….…...6

Features…………………………………………………………………………………………….……. 6

Package Includes…………………………………………………………………………………….…..6

Front & Rear Panel Description

…………..………………………………………………………...….8

• Front Panel Introduction……………………………………………………………………..…8

• Rear panel Introduction………………………………………………………………….…....11

Getting Started………………………………………………………………….…...14

Installation Guide……………………………………………………………………………….……….14

• DVR and Camera Installation……………………………………………………….…….…16

• DVR and Monitor Installation……………………………………………………….………..17

Basic Menu Setup………………………………………………………………...…18

Getting Started with Basic Menu Setup………………………………………………………….…...18

• System Menu……………………………………………………………………………….…20

• Factory Default………………………………………………………………………….…….20

• Clear HDD……………………………………………………………………………….…….21

• Time/ Date Setup………………………………………………………………………….….23

• Record In Motion………………………………………………………………………….…..24

Advance Menu Setup……………………………………………………………....31

System Menu…………………………………………………………………………………………....31

• Display Setup……………………………………………………………………………….….32

• Monitor Setup………………………………………………………………………………..…34

• Configuration…………………………………………………………………………………...35

• HDD Management……………………………………………………………………………..36

o Time/ Date Setup………………………………………………………………….…37

o Camera Setup…………………………………………………………………….….38

• Motion Setup…………………………………………………………….….40

• Interval Setup……………………………………………………………....46

o Alarm Setup……………………………………………………………………….….47

o Event Popup Setup……………………………………………………………….…47

o Buzzer Setup………………………………………………………………………...48

o Password Setup……………………………………………………………..…...….48

o System Information……………………………………………………………….…49

• Record Setup……………………………………………………………………………....….50

o Record Configuration………………………………………………………………..50

• Overwrite………………………………………………………….……..….50

• Multiplex…………………………………………………………….………50

• Quality……………………………………………………………………….51

• Resolution………………………………………………………………..…51

5

• Record in Alarm………………………………………………………….....51

• Record in Motion……………………………………………………..….….51

• Continuous Record……………………………………………………...….51

• Schedule Setup……………………………………………………………………………..…52

• Holiday Setup……………………………………………………….…………..…….….……54

• CD Backup………………………………………………………………………….…….....…54

o CD/ DVD Backup………………………………………………………………….…55

o CD/ DVD Backup Player Software Installation…………………………………...56

• External Devices……………………………………………………………………….….…..60

o TCP/IP Setup…………………………………………………………………..…….60

o RS232C Setup……………………………………………………………………….62

o PANTILT Setup………………………………………………………………………63

o SPOT Setup……………………………………………………………………..…..64

o AUDIO…………………………………………………………………………….….65

• Factory Default……………………………………………………………………………..…66

• LANGUAGE ……………………………………………………………………………….…..67

Advance Hardware Installations

………………………………………………………..…...68

SPOT………………………………………………………………………………………………....68

LOOP……………………………………………………………………………………………..….69

Sensor and Alarm Installation…………………………………………………………………..…70

Serial Port Setup……………………………………………………………………………….…...71

PTZ Camera Installation and Operations……………………………………………………...…73

Microphone and Speaker Installation………………………………………………………….…75

HDD Installation……………………………………………………………………………….……76

Operation…………………………………………………………………………..…77

Display Configuration……………………………………………………………..………….……77

Screen Switch……………………………………………………………………………….….….79

PIP View……………………………………………………………………………………….……79

Freeze View…………………………………………………………………………………….…..79

View in Sequence………………………………………………………………………………….80

Zoom View………………………………………………………………………………………….80

Key Lock………………………………………………………………………………………….…81

Switch Audio Channel………………………………………………………………………….….81

Record………………………………………………………………………………………………82

Playback………………………………………………………………………………………….…83

Search Mode……………………………………………………………………………………….84

Network and Client Software………………………………………………….….88

Network Introduction………………………………………………………………………………88

• Network Installation and Setup…………………………………………………………88

Installing Network Software……………………………………………………………………….94

Dynamic IP Settings…………………………………………………………………………...…101

Remote Live View VIA IE Browser…………………………………………………………..…107

Web Network Backup…………………………………………………………………………....109

Specifications………………………………………………………………………114

Appendix 1 Record Time Table……………………………………….……..….116

Appendix 2 System Configuration………………………………………..……118

Appendix 3 Play Only Mode………………………………………………..……118

6

Product Overview

1. Features

 DVQ 4 records 120 frames per second max using lowest resolution.

 DMR8/16 records 480 frames per second max using lowest resolution.

 Remote viewable via 10/100 Ethernet

 Easily backup hard drive data to DVR-R burner

 Selectable motion detection recording

 Instant search by time, alarm events, etc.

 2 internal hard drive bays

 Password protection

 Jog/Shuttle dial allows frame by frame review

 On-screen setup menu, title, and system timer.

 Time/Date stamp

 Time lapse and real-time recording.

2. Package Includes

• DVQ or DMR unit × 1

• Power Supply × 1

• Power Cable × 1

• Remote Controller × 1

• Manual × 1

• Software CD-R × 1

• Accessories × 1

• Battery × 2

Chapter

1

7

Ca t

DVR-1 CD Manual

REMOTE Power cord Power Supply

Package

NOTE: Check the package to make sure that you receive all accessories which include the

components shown above.

8

Front & Rear Panel Description

Front Panel Introduction

**Special NOTE for line items 6 and 19**

1. DVD+R burner

• Built-in DVD+R burner.

2. USB Port

• Used to connect PC to DVR for firmware upgrade.

• USB memory stick backup.

3. IR Receiver & LED Lamps

• IR Remote Controller Receiver.

• DVR Status LED.

o RUN- Flashes when picture by picture play through J. Shuttle.

o ACTIVE- On when the J. Shuttle is ready for use.

o REC- On while recording and flashes at stand-by mode.

o PLAY- On while playback.

o FULL- On when HDD storage is full.

o NET- On when the DVR is connected remotely.

4. 1~16 Channel Button

• Select channel for full screen display.

5. MODE

• Switch to full or split screen display.

6. **K.LOCK**

• Security lock out to help prevent unwanted DVR access. DO NOT PUSH THIS BUTTON

unless you know what your password is. Default password is blank (_______), press the

“ENTER key” to confirm password. See your “PASSWORD SETUP” to change your

password.

7. MENU

• Enter the menu set up.

9

8. Arrow Keys & ENTER

• Directions- Navigate the menu.

• ENTER- Confirm the selected options.

9. Jog Shuttle

• Use inner Jog shuttle control for frame by frame image display. Turn clockwise for

forward and turn counter-clockwise for reverse.

• Use outer Jog shuttle control for fast forward and fast reverse.

P.1 Appear

10. PTZ

• Press the PTZ buttons to control the PTZ camera directly.

11. [ + / - ]

• Adjust set-up value.

• Control screen display channel.

12. Control

• SEQ/AUDIO - Press for AUDIO. Press and hold for 3 seconds to enter SEQ mode.

• SEQ -Full screen sequencing/ PIP screen sequencing.

• AUDIO - Press to play the audio, and press again to switch audio channels.

• PIP – Press PIP to enter the Picture in Picture mode.

• NEXT –

o Go to the next PTZ command in PTZ mode.

o Switch from full screen display to split screen display.

• ZOOM - Press ZOOM key to enlarge specific picture area.

13. REC

• Press to activate continuous record. Record settings used for recording are Super fine

quality and Best resolution.

14. STOP

• Stop record.

• Stop playback and return to the live mode.

15. SEARCH

• Enter search options. (Percentage, date / time, or the event list).

16. PLAY

• Play recorded video.

17. FREEZE

• Freeze in full screen or split screen

18. J.SHUTTLE Button

• Activate the Jog Shuttle and press again to deactivate

19. **ENTER KEY**. Enter your selections for MENU entries.

10

11

BACK PANEL INTRODUCTION

1. RS485, Relay Output, Sensor Input

• RS485, for connection to PTZ cameras.

• 16 sensor inputs and 1 relay output.

2. VGA Output

• Connection to a VGA monitor or TFT LCD.

12

3. ETHERNET

• LAN connection.

4. RS-232C

• Use to connect to PC or other serial control devices.

5. 1~16 Camera Input/ LOOP Output

• CAMERA IN- channels 1~16 camera input.

• LOOP- channels 1~16 camera video out.

6. Monitor / SPOT Output

• MONITOR - Connection to main monitor.

• SPOT- Alarm or motion triggered monitor output display.

7. Power Input

• DC power input (DC12V)

8. Power Switch

• Power ON/OFF

9. Audio Input/Output

• 1 ~ 4 Audio input channels/ 1 Audio output channel.

IR remote controller introduction

1. MENU

• Enter menu or exit

2. Split /OSD

• 4S: 4 split screen

• 9S: 9 split screen

• 16S: 16 split screen

• AUDIO: Press to play the audio, press again to

go to the next audio channel.

3. 1~16 Channel

• Switch channel in live or playback.

4. Control function

• FRZ - Freeze screen display

• SEQ - Display screen sequence

• ZOOM - Press ZOOM key to enlarge specific

picture area. Use the direction buttons to guide

ZOOM target.

• PIP- Picture in Picture. Enter PIP mode in full

screen

5. Mode/PT

• MODE- Multi-screen display

• P/T- Enter the PTZ camera control mode

13

6. SEARCH/-/+/NEXT

• SEARCH - Open the search window in playback

• [-]/[+] – Adjust options in set-up

• NEXT- Go to the next PTZ command in PTZ mode. / Go to the next channel in full screen

display/ Go to next page in split screen display.

7. Rec

• Continuous Record.

8. Stop

• Stop the record and return to previous record setting.

• Stop playback and return to the LIVE mode.

9. Functions

• PLAY - Play recorded video.

• PAUSE - Pause playback.

• REW - Fast rewind, press again to adjust speed.

• FF - Fast forward, press again to adjust speed.

• STEP - Play frame by frame.

• SLOW - Slow motion playback, press again to adjust speed.

10. ENTER

• Select option.

11. Direction

• Navigate the menu.

14

GETTING STARTED

Installation Guide

Camera and Monitor Installation

This manual has been carefully written to help you assemble and configure your digital video

recorder system for optimal performance. It’s easy to setup your digital video recorder just follow

the instructions on pages 14 through 30 for your basic setup. If you have any comments

questions about this manual, please feel free to call us at 800-335-9777.

1. Remove your monitor from the box for testing your cameras and cables. You can use a TV

set with a video input if you don’t have a monitor. Plug your monitor into a 110-120 AC power

source. Do not mistake the antenna input on the TV for a VIDEO INPUT. Monitors and TV’s

have video inputs clearly marked. The TV RCA input will look some what like the image

below (labeled VIDEO INPUT). This type of input connector is called an RCA female input

jack.

2. Remove your cameras and camera power supplies from the box. Make sure you’re using

power supplies that have a REGULATED POWER SUPPLY 12 VOLT OUTPUT (very

important). Most power supplies have a label on the back that will tell you the type of output

the power supply is capable of producing. If there is no label, DO NOT USE THE POWER

SUPPLY.

Chapter

2

15

NOTE: Un-regulated power supplies are very common and will damage your cameras.

3. Connect each one of your cameras to your regulated power supply and cable assembly.

Most cable assemblies are 100 ft long or more. You will see all types of cable configurations

here is one example of a cable option below.

4. Test each component of your video system prior to installation. Connect each camera

directly to the video monitor, using a new power adapter and cable for each camera. This will

test each component of your video system and confirm proper function prior to installation.

16

5. Connect the digital video recorder to cameras.

DVR and Camera Installation

17

DVR and Monitor Installation

DVR system diagram

18

BASIC MENU SETUP

GETTING STARTED with the BASIC MENU

SETUP

In this section we will cover basic menu settings to get you started and operational right away.

Connect the AC Power Cord with Power Adapter and plug into an electrical AC outlet. Power

switch is on the rear panel, turn the switch on. It will take approximately 5 to 15 seconds for the

system to completely finish initializing.

Caution: Only use 100~240VAC 50~60HZ / 12VDC 8A or 5A power supply.

Chapter

3

19

Before operating the digital video recorder you will need to set up the SYSTEM MENU within the

DVR.

Go into the MENU and run the FACTORY DEFAULT, CLEAR HARD DRIVE and change the

SYSTEM TIME.

1. FACTORY DEFAULT

2. CLEAR HARD DRIVE

3. SYSTEM TIME

BASIC MENU SETUP

1. Press the MENU key on the front panel to login.

2. Use CH. SELECTORS 1 ~ 16 to key in the password.

3. Press ENTER to confirm and you will enter the

Menu system.

NOTE: You don’t have a password in the

system, if this is your first install. Your

password is blank or “(___________) “, do not

enter a password at this time, and hit the >

ENTER key.

20

SYSTEM MENU

CH

AP

.4 Set

Up

FACTORY DEFAULT

4. Press  UP and DOWN

arrow keys and hit the

ENTER key for selection.

Move the cursor to

FACTORY DEFAULT and

hit the ENTER key.

1. DISPLAY SETUP

2. CONFIGURATION

3. RECORD SETUP

4. BACK-UP

5. EXTERNAL DEVICE

6. FACTORY DEFAULT

7. LANGUAGE

Page is loading ...

Super Circuits DMR16CD-3 User manual

This manual is also suitable for

Super Circuits DMR16CD-3 User manual

Related papers

Other documents