LBL Lighting HW623SMSC2G Installation guide

LBL Lighting
Brand
LBL Lighting
Model
HW623SMSC2G
Type
Installation guide

This manual is also suitable for

1
Installation Instructions for
Mini-Rock Candy Cylinder Wall
980MROCKCW
CAUTION - RISK OF FIRE
This product requires installation by a qualified
electrician. Before installing be sure to read all
instructions and TURN THE POWER TOTHE
ELECTRICAL BOX OFF.
Install the Fixture
GENERAL PRODUCT INFORMATION:
This product is suitable for damp locations.
This product can mount either to a 4” square electrical box with a
round plaster ring or an octagon electrical box.
This product can be dimmed with a standard incandescent dimmer.
This instruction shows a typical instruction.
With the Allen wrench provided, back out (do not fully
remove) the set screws at the base of the fixture.
Remove the mounting plate from the back of the
fixture.
1
1.0
WALL
1A
2
HW623_2G
ALLEN WRENCH
SET SCREW
MOUNTING
PLATE
1
1B
Attach the mounting plate to the electrical box using
the two #8-32 screws provided. Make sure the notched
end of the mounting plate is at the top.
NOTCHED END
#8-32 SCREW
MOUNTING
PLATE
3
3
3
2
1C
4
5
6
1E
6
67
69
610
Verify that the mounting plate is level before continuing.
Line up an anchor tip with the center of the mounting
plate hole and push the anchor into the wall up to the
threads.
Screw the anchors in the rest of the way.
Repeat steps 4-6 for the other anchor.
ANCHOR
ANCHOR
Slide a #8 screw through a washer and screw it into an
anchor. Repeat for the other anchor to secure the
mounting plate to the wall.
SCREW
WASHER
SCREW
WASHER
1D
68
SCONCE
Connect the mounting plate ground wire to a suitable
ground in accordance to local electrical codes.
Connect the white fixture wire to the neutral power line
wire with a wire nut.
Connect the black fixture wire to the hot power line
wire with a wire nut.
611
Hook the top of the sconce to the top of the mounting
plate and swing the bottom of the sconce toward the
plate until it is flush with the wall.
Tighten the set screw at the bottom of the sconce to
secure it to the mounting plate.
1F
9
12
10
11
13
612
613
3
Install the Lamp and Shades
Push the lamp base completely into the socket.
CAUTION: To reduce the risk of a burn or electric
shock during relamping, disconnect the power to
the fixture.
LAMP
SOCKET
NOTE: Use only your fingers and a soft cloth to
replace the lamp.
Use Volt, type T4, G9 base
bi-pin halogen lamp in each socket.
MAX 60120 Watt
1
2A
2B
Gently push the inner glass shade into the center of the
socket assembly base until it is firmly in place.
2
2C
Carefully screw the outer glass shade onto the socket
assembly base until it is firmly in place.
3
SOCKET
ASSEMBLY
BASE
INNER
GLASS
SHADE
SOCKET
ASSEMBLY
BASE
OUTER
GLASS
SHADE
NOTE: To re-lamp, reverse the section 2 instructions.
4
SAVE THESE INSTRUCTIONS!
7400 Linder Ave, Skokie, IL 60077
800.323.3226 - 847.626.6300
www.lbllighting.com
© 2012 LBL Lighting.All rights reserved.The "LBL Lighting" graphic is a
registered trademark of LBL Lighting. LBL Lighting reserves the right to
change specifications for product improvements without notification.
A Generation Brands Company
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

LBL Lighting HW623SMSC2G Installation guide

LBL Lighting
Brand
LBL Lighting
Model
HW623SMSC2G
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents