American Pro Decor 5APD10761 Installation guide

American Pro Decor

Brand: American Pro Decor

Model: 5APD10761

Type: Installation guide

American Pro Decor 5APD10761 is a hardware kit designed for sliding single wood doors. It is made of 304 Grade Stainless Steel and includes all the necessary components for installation, such as a 96" rail, door roller hardware, end brackets, center brackets, bolts, screws, floor anchors, a routed floor guide, and door stops.

The kit is designed to be easy to install, with adjustable mounting brackets that allow for standard 16" U.S. stud spacing or any variation. The brackets must be secured into wall blocking for maximum weight capacity.

To install, find the centerline of the track and mark a horizontal line twice the door width long. Mark the bracket screw locations into the wall blocking and attach the wall portion of the brackets. Then, attach the rail to the wall.

American Pro Decor 5APD10761 is a hardware kit designed for sliding single wood doors. It is made of 304 Grade Stainless Steel and includes all the necessary components for installation, such as a 96" rail, door roller hardware, end brackets, center brackets, bolts, screws, floor anchors, a routed floor guide, and door stops.

The kit is designed to be easy to install, with adjustable mounting brackets that allow for standard 16" U.S. stud spacing or any variation. The brackets must be secured into wall blocking for maximum weight capacity.

To install, find the centerline of the track and mark a horizontal line twice the door width long. Mark the bracket screw locations into the wall blocking and attach the wall portion of the brackets. Then, attach the rail to the wall.

TOOLS REQUIRED

INCLUDED IN KIT

• Plumb Line

• Pencil

• Phillips Head Screwdriver

• 10mm Drill Bit

• 5.5mm Drill Bit

• Level

• Tape Measure

• Power Drill

A

B

C D E

F G H I

J

A

96" Rail x1

B

Door Roller Hardware x2

C

End Bracket x2

D

Center Bracket x3

E

ST4.8x50 Bolt x5

F

ST5.5x32 Screw x3

G

Floor Anchor x3

H

Routed Floor Guide x1

I

Door Stops x2

J

4mm/6mm Allen Keys x1

304 Grade Stainless Steel

MODEL No.

5APD10761

INSTALLATION MANUAL

HARDWARE KIT

FOR SLIDING SINGLE WOOD DOORS

American Pro Decor assumes no liability for improper installation.

Wall Blocking

1. To obtain maximum weight capacity, all fasteners

must be mounted into solid wood studs or wall

blocking or mounted to a header board.

2. Adjustable mounting brackets allow for standard

16" U.S. stud spacing, or any variation.

Suggested wall bracket spacing.

Brackets must be secured into wall blocking.

Attach rail to wall as shown.

NOTES

Find the centerline of the track. Using a level, mark

a horizontal line twice the door width long. Mark the

bracket screw locations into the wall blocking.

Attach the wall portion of the brackets as shown.

Consult a structural engineer if you have questions

about what type of wall blocking is required.

American Pro Decor assumes no liability for improper installation.

Remove the anti-rise pin using the provide Allen key.

Plumb the door and mark the positions of the oor guides.

Mount the oor guides to the oor.

Position the doors on the rail.

1-3/16" (30mm)

Drill holes in the top of the door from the edge

as pictured to accommodate the door rollers.

The bottom of the doors should be routed at

this time in order to accept the oor guide.

American Pro Decor assumes no liability for improper installation.

Adjust the door stops accordingly. Tighten the set screw with sufcient

force to drive the set screw into the bar after making the nal adjustment.

Reattach the anti-rise pin to the door rollers

American Pro Decor assumes no liability for improper installation.

1
2
3
4

American Pro Decor 5APD10761 Installation guide

American Pro Decor

Brand: American Pro Decor

Model: 5APD10761

Type: Installation guide

American Pro Decor 5APD10761 is a hardware kit designed for sliding single wood doors. It is made of 304 Grade Stainless Steel and includes all the necessary components for installation, such as a 96" rail, door roller hardware, end brackets, center brackets, bolts, screws, floor anchors, a routed floor guide, and door stops.

The kit is designed to be easy to install, with adjustable mounting brackets that allow for standard 16" U.S. stud spacing or any variation. The brackets must be secured into wall blocking for maximum weight capacity.

To install, find the centerline of the track and mark a horizontal line twice the door width long. Mark the bracket screw locations into the wall blocking and attach the wall portion of the brackets. Then, attach the rail to the wall.

Download PDF

Related papers

Other documents