Legrand LMLS-MB1/MB2 DLM Photosensor Mounting Brackets Installation guide

Legrand
Brand
Legrand
Model
LMLS-MB1/MB2 DLM Photosensor Mounting Brackets
Type
Installation guide
SPECIFICATIONS
Material: ....................................... ABS, UL 94 5V
..................................Flame Retardent Material
..........................................Indoor Use Only
Mounting Options:
LMLS-MB1 ....................................4-Square J-Box
............................................2-Gang J-Box
LMLS-MB2 ......................................Screw to Wall
..........................Tape to wall with double sided tape
Installation Instructions
LMLS-MB1/MB2
Digital Lighting Management (DLM)
Photosensor Mounting Brackets
LMLS-MB1
LMLS-MB2
Call 800.879.8585 for Technical Support
DESCRIPTION
The LMLS-MB1 and LMLS-MB2 mounting brackets provide the flexibility to
mount the LMLS-400 and LMLS-500 Photosensors to walls, skylight wells or
J-Boxes. They are specifically designed to be used in conjunction with these
Photosensors.
LMLS-MB1
J-Box mounted
LMLS-MB2
Skylight wall
mounted
Mounting bracket
Cabling
Or
Remove
tab
Skylight light well
Surface Mount using
Mounting Bracket
Ceiling Mounting bracket
Ceiling or Ceiling Tile
Surface Mount
using LMLS-MB2
Mounting Bracket
www.wattstopper.com
Mounting plate
back view
2-gang
Hole for
4"Square
J-box
2-gang
2-gang 2-gang
Hole for
2-gang
wall box
Hole for
2-gang
wall box
Hole for
4"Square
J-box
Hole for
2-gang
wall box
Hole for
2-gang
wall box
Using a small screwdriver, punch out the holes for the corresponding junction
box. Holes are clearly marked on the rear side of mounting plate.
LMLSMB1 MOUNTING OPTIONS
The LMLS-MB1 is designed to be able to mount to a standard 4" square
junction box as well as a 2-gang junction box.
Call 800.879.8585 for Technical Support
Mounting to a
4” square Jbox
Mounting to a
2 gang wall box
LMLS-MB1 MOUNTING INSTRUCTIONS
CONNECTING THE RJ-45 CABLE
Connect RJ-45 cable and photosensor as shown.
Run RJ-45 cable
through J-box.
After punching out the holes, use the provided screws to mount the
LMLS-MB1 to the corresponding junction box as shown.
4 square J-box
2 screws
2-gang
4 screws
Slide sensor into
the LMLS-MB1
to finish.
www.wattstopper.com
LMLSMB2 MOUNTING OPTIONS
The LMLS-MB2 can be mounted to a wall with the provided screws or by
using the double-sided tape. Using the provided template, marking the wall
with appropriate hole spacings is made easy. The
LMLS-MB2 has a small break-away tab at the
bottom of the bracket for use when running the
RJ-45 cable on the wall surface if desired.
For the screw holes, use a #40 drill gauge bit size
to drill a 0.098"pilot hole. If drilling through a wall
the recommended hole size diameter to drill for
the cable is 0.875".
MOUNTING WITH SCREWS
1. Use template to mark
wall with appropriate hole
spacings.
2. Drill screw pilot holes using #40 drill bit.
Break-away
tab
Hole size diameter to drill
for cable is 0.875"
0.098"pilot
holes
3. Use provided screws to
mount the LMLS-MB2 to
the wall.
Align screw holes on
mounting bracket to
markings on wall.
Call 800.879.8585 for Technical Support
LMLSMB2 PLACEMENT EXAMPLE
Cable goes
through wall
Cable goes
on wall surface
Or
Mounting when running the
RJ-45 cable through wall.
Mounting when running the RJ-45
cable on the wall surface.
0.098"pilot
holes
0.098"pilot
holes
RJ-45 Cable Going
Through Wall
Run On the Wall Surface
Or
Remove tab
when running RJ-45 cable
on the wall surface
Slide sensor into the
LMLS-MB2 wall mount
bracket to finish.
WIRING DETAIL
Connect RJ-45 cable and photosensor as shown.
Template hole size diameter
to drill for cable is 0.875".
Plug
RJ-45
cable
into the
RJ45
socket on
the end of
the unit.
Run RJ-45 cable
through wall.
www.wattstopper.com
Break-away
tab
MOUNTING WITH DOUBLE-SIDED TAPE
The LMLS-MB2 can be mounted to a wall using the double-sided tape. Using
the provided template, mark the wall with the appropriate hole spacings . The
LMLS-MB2 has a small break-away tab at the bottom of the bracket for use when
running the RJ-45 cable on the wall surface if desired.
LMLSMB2 MOUNTING OPTIONS
PLACEMENT EXAMPLE
Cable goes
through wall
Cable goes
on wall surface
Or
Mounting when running the
RJ-45 cable through wall.
Mounting when running the RJ-45
cable on the wall surface.
0.098"pilot
holes
0.098"pilot
holes
Template hole size diameter
to drill for cable is 0.875".
Use template to mark
wall with appropriate
hole spacings.
2800 De La Cruz Boulevard, Santa Clara, CA 95050
800.879.8585 • www.wattstopper.com
14677 r1 06/11
Visually align to markers on
wall, then press on wall.
Apply tape to rear recess
as shown.
MOUNTING INSTRUCTIONS
Tape
WIRING DETAIL
Or
Remove tab
when running RJ-45 cable
on the wall surface
Connect RJ-45 cable and
photosensor as shown.
RJ-45 Cable Going
Through Wall
Run On the Wall
Surface
Slide sensor into
the LMLS-MB2 wall
mount bracket to
finish.
Drawn by: ROBERTSON:
PLM: DT
Tech Writing: CR
Eng: AF
QA
TITLE BOX PG. Scale: 1 : 1
REV ECO # INT REV DATE APPROVED
1 C04592 CR 6/30/2011 CG
Title: LMLS-MB1 and LMLS-MB2 Installation
Instructions
Drawing #: Original Drwg. Date: 09 JUN 11 Rev #:
14677
Rev. Date: 30 JUN 11 1
• Material: White 80g/m sq. uncoated
(prefer recycled stock)
• Final trim size: 16" (Wide) x 6" (High).
• Four (4) fold. 2 sided.
• Final folded size: 4" (Wide) x 6" (High).
• Ink Color: CYMK
IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE
ADDITIONAL FILE FORMATTING, PLEASE CONTACT Engineering.
All information in this drawing is the property of WattStopper and cannot be
copied or used without the written approval of WattStopper.
TITLE BOX PAGE ONLY.
DO NOT MAKE FILM • DO NOT PRINT
REV ECO # INT REV DATE APPROVED
1 C04592 CR 6/30/2011 CG
Title: LMLS-MB1 and LMLS-MB2 Installation
Instructions
Drawing #: Original Drwg. Date: 09 JUN 11 Rev #:
14677
Rev. Date: 30 JUN 11 1
• Material: White 80g/m sq. uncoated
(prefer recycled stock)
• Final trim size: 16" (Wide) x 6" (High).
• Four (4) fold. 2 sided.
• Final folded size: 4" (Wide) x 6" (High).
• Ink Color: CYMK
IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE
ADDITIONAL FILE FORMATTING, PLEASE CONTACT Engineering.
All information in this drawing is the property of WattStopper and cannot be
copied or used without the written approval of WattStopper.
TITLE BOX PAGE ONLY.
DO NOT MAKE FILM • DO NOT PRINT
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Legrand LMLS-MB1/MB2 DLM Photosensor Mounting Brackets Installation guide

Legrand
Brand
Legrand
Model
LMLS-MB1/MB2 DLM Photosensor Mounting Brackets
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents