Fytech POS790 User manual

USER MANUAL

Point-of-Sale

Hardware

System

VERSION V1.4 DECEMBER 2010

ii

Manual Version 1.4

Part Number: 3LMPP7900214

The information contained in this document is subject to change without notice.

We make no warranty of any kind with regard to this material, including, but not

limited to, the implied warranties of merchantability and fitness for a particular

purpose. We shall not be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing, performance, or use of

this material.

This document contains proprietary information that is protected by copyright. All

rights are reserved. No part of this document may be photocopied, reproduced

or translated to another language without the prior written consent of the

manufacturer.

TRADEMARK

Intel®, Pentium® and MMX are registered trademarks of Intel® Corporation.

Microsoft® and Windows® are registered trademarks of Microsoft Corporation.

Other trademarks mentioned herein are the property of their respective owners.

Safety

IMPORTANT SAFETY INSTRUCTIONS

To disconnect the machine from the electrical power supply, turn off the power 1.

switch and remove the power cord plug from the wall socket. The wall socket must

be easily accessible and in close proximity to the machine.

Read these instructions carefully. Save these instructions for future reference.2.

Follow all warnings and instructions marked on the product.3.

Do not use this product near water.4.

Do not place this product on an unstable cart, stand, or table. The product may fall, 5.

causing serious damage to the product.

Slots and openings in the cabinet and the back or bottom are provided for 6.

ventilation to ensure reliable operation of the product and to protect it from

overheating. These openings must not be blocked or covered. The openings

should never be blocked by placing the product on a bed, sofa, rug, or other

similar surface. This product should never be placed near or over a radiator or heat

register or in a built-in installation unless proper ventilation is provided.

This product should be operated from the type of power indicated on the marking 7.

label. If you are not sure of the type of power available, consult your dealer or local

power company.

Do not allow anything to rest on the power cord. Do not locate this product where 8.

persons will walk on the cord.

Never push objects of any kind into this product through cabinet slots as they 9.

may touch dangerous voltage points or short out parts that could result in a re or

electric shock. Never spill liquid of any kind on the product.

iii

CE MARK

This device complies with the requirements of the EEC directive 2004/108/EC

with regard to “Electromagnetic compatibility” and 2006/95/EC “Low Voltage

Directive”.

FCC

This device complies with part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that

may cause undesired operation.

CAUTION ON LITHIUM BATTERIES

There is a danger of explosion if the battery is replaced incorrectly. Replace only

with the same or equivalent type recommended by the manufacturer. Discard

used batteries according to the manufacturer’s instructions.

Battery Caution

Risk of explosion if battery is replaced by an incorrectly type.

Dispose of used battery according to the local disposal instructions.

Safety Caution

Note: To comply with IEC60950-1 Clause 2.5 (limited power sources, L.P.S)

related legislation, peripherals shall be 4.7.3.2 “Materials for fire enclosure”

compliant

4.7.3.2 Materials for  re enclosures

For MOVABLE EQUIPMENT having a total mass not exceeding 18kg.the material

of a FIRE ENCLOSURE, in the thinnest signi cant wall thickness used, shall be

of V-1 CLASS MATERIAL or shall pass the test of Clause A.2.

For MOVABLE EQUIPMENT having a total mass exceeding 18kg and for all

STATIONARY EQUIPMENT, the material of a FIRE ENCLOSURE, in the thinnest

signi cant wall thickness used, shall be of 5VB CLASS MATERIAL or shall pass

the test of Clause A.1

iv

LEGISLATION AND WEEE SYMBOL

2002/96/EC Waste Electrical and Electronic Equipment Directive on the treatment,

collection, recycling and disposal of electric and electronic devices and their

components.

The crossed dust bin symbol on the device means that it should not be disposed

of with other household wastes at the end of its working life. Instead, the device

should be taken to the waste collection centers for activation of the treatment,

collection, recycling and disposal procedure.

To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate this from other types of wastes and recycle it

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this

product, or their local government office, for details of where and how they can

take this item for environmentally safe recycling.

Business users should contact their supplier and check the terms and conditions of

the purchase contract.

This product should not be mixed with other commercial wastes for disposal.

v

Revision History

Changes to the original user manual are listed below:

Revision Description Date

1.0 Initial release• 2007 August

1.1

Cover page update•

System View update•

System Installation update•

System Disassembly update•

Specication update •

2007 December

1.2 Performance model info. added• 2008 January

1.3

B68 motherboard Added•

B78 motherboard updated to v2.2•

B98 motherboard Added•

Format Change•

Jumper Setting updated•

2009 December

1.4

SSD Card Replacement Added•

C48 motherboard Added•

2010 December

vi

Table of Contents

1. Packing List .............................. 1

1-1. Standard Accessories ..............................................1

1-2. Optional Accessories ...............................................2

2. System View ............................. 3

2-1. Front View ...............................................................3

2-2. Side View .................................................................3

2-3. Rear View with stand ...............................................4

2-4. Rear View without wall mount bracket .....................4

2-5. I/O Ports View ..........................................................5

2-6. System Dimension ...................................................6

3. System Assembly .................... 7

3-1. HDD replacement for fan system ............................7

3-2. HDD replacement for fanless system ......................7

3-3. RAM Replacement ..................................................8

3-4. Power Adapter Replacement ...................................9

4. Peripheral Installation ............ 10

4-1. MSR Installation .....................................................10

4-2. VFD Installation ......................................................10

4-3. Wall Mount Kit Assembly ........................................ 11

4-4. Desktop Stand Assembly ........................................12

4-5. Wireless LAN Installation ........................................13

4-5-1. On a Fan System .................................................... 13

4-5-2. On a Fanless System .............................................. 14

vii

4-6. SSD Card Replacement .........................................15

4-6-1. On a Fan System .................................................... 15

4-6-2. On a Fanless System .............................................. 16

4-7. Cash Drawer Installation .......................................17

4-7-1. For B78 motherboard .............................................. 17

4-7-2. For B68/B98/C48 motherboard ............................... 19

5. Specication ........................... 21

6. Jumper Setting ........................ 23

6-1. For B68 Motherboard .............................................23

6-1-1. Motherboard Layout ................................................ 23

6-1-2. Connectors & Functions .......................................... 24

6-1-3. Jumper Setting ........................................................ 26

6-2. For B78 Motherboard .............................................29

6-2-1. Motherboard Layout ................................................ 29

6-2-2. Connectors & Functions .......................................... 30

6-2-3. Jumper Setting ........................................................ 31

6-3. For B98 Motherboard .............................................34

6-3-1. Motherboard Layout ................................................ 34

6-3-2. Connectors & Functions .......................................... 35

6-3-3. Jumper Setting ........................................................ 36

6-4. For C48 Motherboard .............................................39

6-4-1. Motherboard Layout ................................................ 39

6-4-2. Connectors & Functions .......................................... 40

6-4-3. Jumper Setting ........................................................ 41

Appendix: Drivers Installation .... 46

1

Packing List1.

Standard Accessories

1-1.

a.

b.

c.

d.

e.

f.

System (with stand)a.

Driver bankb.

User guidec.

Power adapterd.

Power corde.

RJ45-DB9 cable (x2)f.

2

Optional Accessories

1-2.

a.

b.

c.

d.

e.

Metal MSRa.

Metal VFDb.

Wall-mount Kitc.

SSD moduled.

WLAN Card (with internal antenna)e.

a

b

c

3

2

System View2.

Front View

2-1.

Side View

2-2.

3

4

5

Fanless System Fan System

Item No. Description

1 Touch Screen

2 MSR Module (Optional)

3 External Antenna (Optional)

4 Hinge Cover for stand installation

5 Stand

1

4

Rear View with stand

2-3.

6

7

8

9

Fan System

Fanless System

Rear View without wall mount bracket

2-4.

11

10

Fan System

Fanless System

Item No. Description

6 VFD (Optional)

7 HDD Door for fan system

8 Ventilation for fan system

9 Cable management outlet

10 VESA hinge bracket

11 I/O ports cover

5

I/O Ports View

2-5.

a b

c

d e f g

h ij

Fanless System

a b

c

d e f g

h i

j

Fan System

Item No. Description

a Parallel

b USB x 4

c COM 1, 2, 3, 4 (from right to left)

d Line-out

e MIC-in

f Cash Drawer (12V or 19V, can support 24V)

g LAN

h Power Switch

i DC-In

j PS/2

Note: The I/O ports location may slightly different depending to the fan or

fanless system installed.

6

System Dimension

2-6.

386 mm

308 mm

220 mm

370 mm

62 mm

250 mm

80 °

411 mm

390 mm

220 mm

407 mm

63 mm

250 mm

80 °

15" System 17" System

7

System Assembly3.

Turn to the rear side of the system.1.

Unscrew the screw (x1) securing 2.

the HDD door and the rear cover

of the system.

Disconnect the SATA cable from 3.

the drive.

HDD replacement for fan system

3-1.

HDD replacement for fanless system

3-2.

To remove and replace the HDD, please follow below steps. The procedures may

be different depending on the fan or fanless system being installed.

Turn to the rear side of the system 1.

and unfasten the screws (x17) to

separate the rear cover from the

system. The HDD is installed on the

motherboard. If your system install

with a stand or a wall mount bracket,

please remove them beforehand.

(Refer to Chapter 4-3 or 4-4)

Disconnect the HDD cable and 2.

replace the HDD.

8

Removing a RAM module

Please Open the rear cover by 1.

unfasten the screws (x17) to

access the motherboard.

Use both fingers to pull the ejector 2.

clips out of the sides of the module.

Slide out to take out the memory 3.

module from the memory slot.

Installing a RAM module

Slide the memory module into the 4.

memory slot and press down until

it fix with the ejector clips.

RAM Replacement

3-3.

Please open the rear cover (see Chapter 3-1 or 3-2) rst then remove and

replace the RAM module. You can refer to the motherboard layout to nd the

memory compartment. (See chapter 6 for different motherboard)

9

Power Adapter Replacement

3-4.

Disconnect the power cable from 1.

the adapter pre-installed in the

power bracket attached in the

stand.

Unscrew the screws (x2) and 2.

separate the power bracket from

the stand.

Disconnect the other end of the 3.

power adapter from the connector

on the I/O panel.

Draw out the power adapter gently 4.

through the cable management

hole on the stand.

Replace the power adapter by 5.

reversing the procedure of above

steps.

10

Peripheral Installation4.

MSR Installation

4-1.

Unfasten the thumb screws (x2) to 1.

remove the I/O cover.

Connect the MSR module into the 2.

system and fasten the screws (x2).

Connect the PS/2 Connector into 3.

the PS/2 port on the I/O panel.

Note: the PS/2 port locates in different

places on the I/O panel according

to the fan or fanless system being

installed.

Connect the VFD metal bracket 1.

into the system with screws (x2)

Fasten the VFD module to the 2.

metal bracket by fastening the

thumb screws (x2).

Connect the VFD cable to the 3.

RJ45 connector on the I/O panel.

VFD Installation

4-2.

a

b

c

VFD Accessories

VFD modulea.

VFD metal bracket b.

(with RJ45 cable)

Screws (x2)c.

11

Wall Mount Kit Assembly

4-3.

Fix the metal bracket (a) to the 1.

VESA bracket and the display with

the screw (b) (x1).

Align the tear drop holes of the 2.

wall mount bracket (c) into the 4

VESA bracket screws.

Fasten the thumb screw of the 3.

wall mount bracket (a) to fix the

wall mount bracket (c) to the VESA

bracket.

Accessories items

a. Metal bracket with thumb screw

b. Screw x 1

c. Wall mount bracket

c

a

b

c

12

a

f

b

d

e

c

Desktop Stand Assembly

4-4.

VESA bracket assembly

Align the standard VESA mounting 1.

holes of the VESA bracket (a) and

the display and fix them with the

screws provided (f) (x4).

Stand bracket assembly

Align the guide slot of the stand 2.

bracket (b) into the hinge shaft of

the stand (c).

Fasten the screws (e) (x3) on each 3.

sides to fix the stand bracket (b) to

the stand (c).

Align the hinge cover (d) (x2) into 4.

the right position of the stand

bracket (b) and fix it until you hear

a click sound.

Align the screws (f) (x4) on the 5.

VESA bracket (a) pre-installed on

the display to the four tear drop

holes of the stand bracket (b) pre-

installed with the stand.

Accessories items

a. VESA bracket

b. Stand bracket

c. Stand

d. Hinge cover x2

e. Screws for both sides of stand x6

f. Screws for VESA bracket x 4

a b c d e f

13

Wireless LAN Installation

4-5.

Disconnect the HDD cable from the 1.

system first (see Chapter 3-1).

Unscrew the screws (x17) to 2.

remove the rear cover (a).

Assemble the antenna cable (b) 3.

by fasten the nut, washer

and the coaxial cable as

picture instructs.

Insert the WLAN card 4.

(c) to the WLAN socket

on the motherboard and

press it downward until the

ejector clips lock it in place.

Connect the antenna cable to the 5.

“main connector” on the WLAN

card.

Cover the rear cover by reversing 6.

the step 2.

The pre-drilled hole for the external 7.

antenna installation is built in

the side of the rear cover on a

fan system. Rotate the external

antenna clockwise and fasten

to the connector of the internal

antenna cable.

On a Fan System4-5-1.

c

b

a

Page is loading ...

Fytech POS790 User manual

This manual is also suitable for

Fytech POS790 User manual

Other documents