Panduit 1m, Cat 6 STP Installation guide
- Category
- Networking cables
- Type
- Installation guide
This manual is also suitable for
INSTALLATION INSTRUCTIONS PN346
© Panduit Corp. 2004
For Technical Support: www.panduit.com/resources/install_maintain.asp
Individual Foil
Conductors
Braid
STP / PIMF
Pair Screen
.5 in
(12.7 mm)
2.0 in
(50.8 mm)
MINI-COM TX6 PLUS Shielded Jack Modules
Part Number: CJS688TP, CJS688TP26
Page 1 of 3
CABLE PREPARATION
2.0 in
(50.8 mm)
Drain wire
Drain wire
Overall Foil
Conductors
Drain wire
FTP / ScTP
Screen
.5 in
(12.7 mm)
2.0 in
(50.8 mm)
Conductors
Braid
S-FTP
Overall Foil
Screen
TERMINATION
1
T568A T568B
2
Note: May also use S-STP / PIMF cable type (conductors, individual foil pair screen, overall foil screen, and braid).
INSTALLATION INSTRUCTIONS PN346
For Technical Support: www.panduit.com/resources/install_maintain.asp
Page 2 of 3
4 2
3 1
2
3 1
4
3
T568A T568B
8
6
5
7
8
6
5
7
4
T568A T568B
10
9
9
10
5
T568A T568B
6
CWST
7
SHIELD INSTALLATION
1 2 3 4
8
CGJT
(OR)
INSTALLATION INSTRUCTIONS PN346
E-mail:
cs@panduit.com
Fax:
(708) 444-6993
For Instructions in Local Languages
and Technical Support:
www.panduit.com/resources/install_maintain.asp
www.panduit.com
2
TIA/EIA
TX6 PLUS Wiring Sequences
Notes:
1. For specified performance, follow TIA/EIA 568-B installation guidelines.
2. CJS688TP Jack Modules can terminate PVC or Plenum rated 22-24
AWG solid or stranded IWC cable with 0.048 inch (1.2 mm) maximum
insulated conductor outside diameter.
3. CJS688TP26 Jack Modules can terminate PVC or Plenum rated 26
AWG stranded IWC cable with 0.048 inch (1.2 mm) maximum insulated
conductor outside diameter.
4. When terminating CJS688TP26 Jack Modules onto STPCTG**BBL
Zone Cords that have been cut in half, wire to T568A wiring scheme.
4. Jack Modules may be re-terminated a minimum of 10 times.
5. For technical and performance information, consult PANDUIT
Technical Support.
As with all Wiring Accessories, the following statements apply:
1. Never install communications wiring during a lightning storm.
2. Never install communications wiring in wet locations unless the jack is
specifically designed for use in wet locations.
3. Never touch uninsulated communications wiring or terminals unless the
communication line has been disconnected at the network interface.
4. Use caution when installing or modifying communication wiring.
18
Pin #’s
8
7
6
5
4
3
2
1
78
46
53
2 1
BOTTOM
TOP
568-A 568-B
IEC 60708-1
8
7
6
5
4
3
2
1
78
46
53
2 1
BOTTOM
TOP
"A" wire "B" wire
TELECOMMUNICATION ROOM SHIELDING CONTINUITY
Page 3 of 3
TERMINATION CAP REMOVAL
1
3
2
3
1
Drain wire
FTP / ScTP
All Metal Patch
Panel Shielding
(OR)
CJSGK-X Kit
2
3
1
S-FTP, STP / PIMF,
S-STP / PIMF
All Metal Patch
Panel Shielding
(OR)
CJSGK-X Kit
-
1
-
2
-
3
Panduit 1m, Cat 6 STP Installation guide
- Category
- Networking cables
- Type
- Installation guide
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Panduit CJS5E88T User manual
-
-
-
Panduit CJ5E88TBU Installation guide
-
-
-
-
-
Panduit CJ5E88TGBU Datasheet
-